1996 Mercury Sable instrument panel

111 [IP30700(ALL)11/94]
To dim the instrument panel lights, rotate the
thumbwheel down. To turn on the interior
lights, turn the thumbwheel all the way up. The
interior lights also come on when any side door
or the liftgate is opened.
[IP30925(ALL)03/95]
Dome Lamps
[IP30950(ALL)03/95]
The front dome lamp is located overhead
between the driver and front passenger seats.
However, if your vehicle is equipped with a
power moon roof, the dome lamp is located
behind the moon roof.
[IP30975(ALL)11/94]
In the wagon, the rear dome lamp is located
overhead near the rear seating positions.
[IP31025(ALL)02/95]
one third page art:0001410-A
The dome/map lamp
[IP31050(ALL)03/95]
Turn the map lamps on and off with the
switches on the lamp. The dome lamp
illuminates when any door is opened. If either
the driver's or passenger's front door is opened
using the outside door handle, the light will
remain on for 25 seconds after the door has been
shut. If any other door is opened or if either of
the front doors is opened using the inside
handle, the lamp will immediately turn off when
the door is closed.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

73
Warning Lights and
Gauges
%*
[LG00500(ALL)05/92]
In your vehicle, the warning lights and gauges
are grouped together on the instrument panel.
We call this grouping a cluster. Your vehicle has
one of the following clusters:
[LG00800(ALL)02/95]
q
Standard cluster
[LG00900(ALL)02/95]
q
Optional cluster
*
[LG01100(ALL)05/94]
If you are not sure which cluster your vehicle
has, check the diagrams on the following pages.
[LG02050(ALL)03/95]The Standard Cluster
[LG02075(ALL)02/95]
The following warning lights and gauges are on
the standard cluster. All of the warning lights
and gauges alert you to possible problems with
your vehicle. Some of the lights listed are
optional. The following sections detail what each
of these indicators means.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

91
Instrument Panel Controls
%*
[IP00400(ALL)04/95]
The main controls for the climate control system,
clock, and radio are in the oval Integrated
Control Panel on the instrument panel.
[IP00410(ALL)04/95]
The controls for the lights and climate control air
registers are also on the instrument panel.
*
[IP00420(ALL)03/95]
Clean the instrument panel lens and woodtone
trim with a soft cloth and a glass cleaner. Do
not use paper towel or any abrasive cleaner to
clean either the lens or the woodtone trim as
these may cause scratches.
%*
[IP00430(ALL)04/95]
NOTE: Any cleaner or polish that increases the
gloss (shine) of the upper part of the
instrument panel should be avoided.
The dull finish in this area is to help
protect the driver from undesirable
windshield reflection.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

92 [IP00470(ALL)04/95]
full page art:0000661-JInstrument panel
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

94 [IP03300(ALL)03/95]Function selector knob
[IP03351(ALL)04/95]
The function selector knob controls airflow to
the inside of the vehicle.
[IP03401(ALL)03/95]
MAX A/C
[IP03450(ALL)03/95]
MAX A/C uses recirculated air to cool the
vehicle. It allows for faster cooling but is noisier
than A/C. The airflow will be from the
instrument panel registers.
[IP03501(ALL)03/95]
A/C
[IP03550(ALL)04/95]
A/C uses outside air to cool the vehicle. It is
quieter that MAX A/C, but not as economical.
The airflow will be from the instrument panel
registers.
[IP03601(ALL)03/95]
VENT
[IP03650(ALL)03/95]
VENT brings in outside air through the
instrument panel registers. It can be used for
heating or ventilating.
[IP03701(ALL)03/95]
OFF
[IP03750(ALL)03/95]
In OFF, outside air is shut out and the fan will
not operate.
[IP03801(ALL)04/95]
S(Panel and floor)
[IP03850(ALL)04/95]
This brings in outside air through the instrument
panel registers and the front and rear floor
ducts. It can be used for heating or ventilating.
[IP03901(ALL)04/95]
R(Floor)
[IP03950(ALL)04/95]
This allows for maximum heating. The airflow is
from the front and rear floor ducts.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

95 [IP04001(ALL)04/95]
P(Floor and defrost)
[IP04050(ALL)04/95]
This brings in outside air through the floor ducts
and the windshield defroster ducts. It can be
used for heating or ventilation.
[IP04100(ALL)04/95]
V(Defrost)
[IP04150(ALL)04/95]
This brings in outside air through the
windshield defroster ducts. It can be used to
clear ice or fog from the windshield.
[IP04200(ALL)03/95]
Temperature control knob
[IP04250(ALL)03/95]
The temperature control knob may be adjusted
from cool (blue range) to warm (red range).
%*
[IP04700(ALL)04/95]
Electronic Automatic Temperature Control
System
*
[IP04725(ALL)02/95]
The control for your Electronic Automatic
Temperature Control (EATC) is located at the
center of the instrument panel in the Integrated
Control Panel and will operate only when the
ignition is turned on to the ON position.
*
[IP04825(ALL)02/95]
The EATC feature will maintain the temperature
you select and automatically control the airflow
for your comfort. It also allows you to override
the automatic operation with manual override
buttons.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

101
*
[IP07225(ALL)01/95]
Manual override buttons
[IP07325(ALL)04/95]
Your EATC has six buttons which allow you to
make special selections. The buttons are located
along the bottom edge of the EATC and allow
you to determine where the air will be
discharged. Pressing any override button
changes the air discharge location only. It does
not affect the ability of the system to control
temperature or the fan speed. Return to fully
automatic operation by pushing the AUTO
button.
*
[IP07425(ALL)01/95]
MAX A/C button
[IP07525(ALL)04/95]
The MAX A/C feature allows for faster cooling
because air is drawn from inside the vehicle.
Using inside air causes the fan to sound louder
which is normal for this selection. The display
window will change to indicate MAX A/C and
the airflow will be from the instrument panel
registers. To exit, push AUTO or any of the
other five manual override buttons.
%*
[IP07625(ALL)01/95]
VENT button
[IP07725(ALL)03/95]
Press this button to select outside air through
the instrument panel registers. The display
window will show the set temperature and
VENT to the lower right of the temperature.
Your EATC will heat the air if the temperature
you have selected is warmer than the outside air
coming into the vehicle. However, the air will
NOT be cooled regardless of the temperature
setting. Airflow will be from the instrument
panel registers.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

102 [IP07825(ALL)04/95]S(Panel and floor) button
[IP07925(ALL)02/95]
Push this button to get air from the floor and
instrument panel registers at the same time. The
display will show the set temperature andS.
Depending on the selected temperature, the air
will be automatically heated or cooled.
[IP08025(ALL)04/95]
R(Floor)
[IP08125(ALL)03/95]
Airflow will be to the floor when theR(floor)
button is pressed. The display window will
show the set temperature andR(floor) to the
right of the temperature. Fan speed will be
automatic unless manually controlled. If you
override the fan speed and wish to return to
automatic fan control, press AUTO. Then, again
selectR(floor) for airflow to the floor.
[IP08225(ALL)04/95]
P(Floor and defrost)
[IP08325(ALL)02/95]
Press this button to get air to the floor and
windshield defrosters at the same time. The
display will show the set temperature andP.If
the outside temperature is about50ÊF (10ÊC) and
above, the air will be dehumidified to remove
moisture. This will help to prevent fogging in
humid weather.
[IP08425(ALL)04/95]
VF-DEF (Front defrost)
[IP08525(ALL)02/95]
Press theVF-DEF (front defrost) button to
obtain maximum airflow to the windshield.
Adjust the temperature setting as required for
defrosting. The Display window will show the
temperature setting withVto the right of the
temperature. When the outside temperature is
about50ÊF (10ÊC) andabove, the air will be
dehumidified to remove moisture. This will help
prevent fogging in humid weather.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995