1996 Mercury Sable brake

107 [IP25250(ALL)02/89]
To change your headlamps from low to high
beam, push the turn signal lever away from you.
To change them back to low beam, pull the
lever toward you.
*
[IP25300(ALL)03/93]
For more information about how the high beam
headlamps work, seeSteering column controlsin
the Index.
%*
[IP25605(ALL)01/95]
Daytime Running Light System
[IP25610(ALL)03/95]
(Canadian and fleet vehicles only)
*
[IP25615(ALL)03/95]
The Daytime Running Light (DRL) system is
designed to turn the high beam headlamps on,
with a reduced light output and without
illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates
when all of the following conditions are met:
*
[IP25620(ALL)03/95]
q
The vehicle is ªrunning.º
*
[IP25625(ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP25630(ALL)03/95]
q
The headlamp system is in the OFF position.
*
[IP25635(ALL)01/95]
NOTE: If you have a vehicle with an
automatic lighting system, the DRL
system is active until the automatic
system turns on the headlamps.
*
[IP25636(ALL)10/94]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
[IP25637(ALL)01/95]
You may notice that the lights flicker when the
vehicle is turned on or off. This is a normal
condition.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

75
*
[LG02400(ALL)01/95]
Indicator Lights and Chimes
%*
[LG02500(ALL)04/95]
Safety Belt Warning Light and Chime
*
[LG02510(ALL)01/95]
This warning light and chime remind you to
fasten your safety belt. The following conditions
will take place:
[LG02550(ALL)02/95]
q
If the driver's safety belt is not buckled when
the key is turned to the ON position, the
light will activate for 1 minute and the chime
will sound for 4 to 8 seconds.
*
[LG02600(ALL)03/95]
q
If the driver's safety belt is buckled while the
light is on or the chime is sounding, both the
light and the chime will turn off.
[LG02650(ALL)02/95]
q
If the driver's safety belt is buckled before the
key is turned to the ON position, the light
will turn on for a short period, but the chime
will not activate.
[LG02700(ALL)02/95]
one inch art:0000107-B
Safety belt warning light
%*
[LG02900(ALL)03/95]
Brake System Warning Light
*
[LG03000(ALL)03/95]
The warning light for the brakes can show two
things Ð that the parking brake is not fully
released, or that the brake fluid level is low in
the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by
your dealer or a qualified service technician.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

76 [LG03300(ALL)02/95]
one inch art:0000108-DBrake system warning light
*
[LG03500(ALL)01/95]
This light comes on when the parking brake is
set, or if it is not set, it comes on briefly when
you turn the ignition to the START position. It
normally goes off shortly after the engine starts
and you release the parking brake. If the light
stays on after you have fully released the
parking brake, have the hydraulic brake system
serviced by your dealer or a qualified service
technician.
*
[LG03700(ALL)01/95]
RWARNING
The BRAKE light indicates that the
brakes may not be working properly.
Have the brakes checked
immediately. Brake failure may result
in serious personal injury or vehicle
damage.
%*
[LG03800(ALL)01/95]
Charging System Light
*
[LG03900(ALL)03/95]
This light, shown as a battery symbol on your
cluster, indicates that your battery is not being
charged and that you need to have the electrical
system checked.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

83 [LG08251(ALL)11/94]
Speed Control Indicator Light
(If equipped)
[LG08301(ALL)02/95]
This light comes on when the speed control ON
switch is pressed. It turns off when the speed
control OFF switch is pressed or when the
ignition is turned to the OFF position.
[LG08351(ALL)02/95]
one inch art:0001376-A
Speed control indicator light
%*
[LG08391(ALL)02/95]
Anti-lock Brake System Warning Light
(If equipped)
*
[LG08392(ALL)01/95]
This light comes on for a few seconds when you
turn the ignition key to the START position. It
should go off shortly after the engine starts. If it
stays on longer than five (5) seconds, it indicates
that your anti-lock brake system may not be
working properly. Normal braking is not
affected unless the BRAKE system warning light
also remains on for longer than six (6) seconds.
You should have your vehicle serviced
immediately by your dealer or qualified service
technician to restore the benefits of the anti-lock
feature. SeeAnti-lock brakesin the Index for more
information.
[LG08394(ALL)03/95]
one inch art:0000674-D
Anti-lock brake system warning light
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

89 [LG15800(ALL)04/95]
Low Fuel Light (If equipped)
[LG15900(ALL)03/95]
This light comes on when your fuel gauge
indicates approximately 1/16 of a tank. The
ignition must be turned to the ON position for
this light to come on. This light will glow
steadily.
[LG16000(ALL)04/95]
one inch art:0000116-C
Low fuel light
[LG16100(ALL)02/95]
Rear Lamp Out Indicator (If equipped)
[LG16200(ALL)02/95]
This light indicates that a rear tail lamp or
brakelamp is not functioning. It comes on
momentarily when the ignition is turned to the
START position, then goes out.
[LG16220(ALL)02/95]
This light will come on to show a rear tail lamp
burnout when the light switch is turned to the
parking lamp or headlamp position.
[LG16260(ALL)04/95]
This light will come on to show a brakelamp
burnout only when the brake pedal is pressed.
[LG16280(ALL)02/95]
The light will stay on until the ignition is turned
to the OFF position.
[LG16300(ALL)02/95]
one inch art:0000117-B
Rear lamp out light
[LG16400(ALL)12/91]
NOTE: The warning light may not work or
you may get a false reading if you use
trailer lights or use improper
replacement bulbs.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

107 [IP25250(ALL)02/89]
To change your headlamps from low to high
beam, push the turn signal lever away from you.
To change them back to low beam, pull the
lever toward you.
*
[IP25300(ALL)03/93]
For more information about how the high beam
headlamps work, seeSteering column controlsin
the Index.
%*
[IP25605(ALL)01/95]
Daytime Running Light System
[IP25610(ALL)03/95]
(Canadian and fleet vehicles only)
*
[IP25615(ALL)03/95]
The Daytime Running Light (DRL) system is
designed to turn the high beam headlamps on,
with a reduced light output and without
illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates
when all of the following conditions are met:
*
[IP25620(ALL)03/95]
q
The vehicle is ªrunning.º
*
[IP25625(ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP25630(ALL)03/95]
q
The headlamp system is in the OFF position.
*
[IP25635(ALL)01/95]
NOTE: If you have a vehicle with an
automatic lighting system, the DRL
system is active until the automatic
system turns on the headlamps.
*
[IP25636(ALL)10/94]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
[IP25637(ALL)01/95]
You may notice that the lights flicker when the
vehicle is turned on or off. This is a normal
condition.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

123 [SC09350(ALL)03/95]
NOTE: When driving uphill, especially with a
heavy load, you may notice your speed
decreasing even if you have the speed
control set. If the speed drops more
than 8 to 14 mph (13-23 km/h) it is
normal for the automatic speed control
feature to be cancelled. You may need
to use the accelerator pedal to help
your vehicle maintain the selected
speed when driving up steep grades.
%*
[SC09400(ALL)01/95]
Resetting the Speed Control
*
[SC09410(ALL)03/95]
To reset the speed control to alower speed, use
one of the following procedures:
*
[SC09415(ALL)03/95]
q
COASTÐ Press and hold the COAST switch.
Release the switch when the vehicle slows
down to the desired speed.
*
[SC09420(ALL)03/95]
q
Lightly tap the brake pedal. When the vehicle
attains the desired speed, press the SET
ACCEL switch and release it immediately.
[SC09425(ALL)11/94]
q
TAP-DOWNÐ Press and then quickly
release the COAST switch. Each time you
ªtapº the switch, the set speed will decrease
by 1 mph (1.6 km/h). Multiple taps will
cause the set speed to decrease in increments
of 1 mph (1.6 km/h). For example, if the
current set speed is 60 mph (96 km/h) 5 taps
of the COAST switch will decrease the
vehicle speed and SET it at 55 mph
(88 km/h).
*
[SC09430(ALL)04/95]
If vehicle speed is reduced below 30 mph
(50 km/h) by any of the above methods, then
you must manually accelerate to a speed over
30 mph (50 km/h) and reset the system.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

124 [SC09435(ALL)02/95]To reset the speed control to ahigher speed,use
one of the following procedures:
*
[SC09440(ALL)03/95]
q
ACCELÐ Press and hold the SET ACCEL
switch. Release the switch when the vehicle
has accelerated to the desired speed.
*
[SC09445(ALL)03/95]
q
Depress the accelerator pedal. When the
vehicle attains the desired speed, press the
SET ACCEL switch and release it
immediately.
[SC09450(ALL)11/94]
q
TAP-UPÐ Press and then quickly release the
SET ACCEL switch. Each time you ªtapº the
switch, the set speed will increase by 1 mph
(1.6 km/h). Multiple taps will cause the set
speed to increase in increments of 1 mph
(1.6 km/h). For example, if the current set
speed is 55 mph (88 km/h) 5 taps of the SET
ACCEL switch will increase the vehicle speed
and SET it at 60 mph (96 km/h).
%*
[SC10900(ALL)03/95]
Cancelling and Resuming a Set Speed
[SC11000(ALL)04/95]
If you press the brake pedal, speed control is
cancelled. You can return to the set speed by
pressing the RESUME switch, as long as you did
not press the OFF switch. You must be driving
at least 30 mph (50 km/h).
*
[SC11300(ALL)03/95]
Your vehicle will gradually return to the
previously set speed and then maintain it.
%*
[SC11315(ALL)03/95]
To Turn Off the Speed Control System
*
[SC11325(ALL)04/95]
Press the OFF switch.
*
[SC11400(ALL)04/95]
In addition, the speed control is turned off each
time you turn the vehicle off.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995