1996 Mercury Mystique brake

56
*
[LG02900(ALL)03/95]
Brake System Warning Light
*
[LG03000(ALL)03/95]
The warning light for the brakes can show two things Ð that
the parking brake is not fully released, or that the brake fluid
level is low in the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by a qualified service
technician.
[LG03400(ALL)01/95]
6 pica art:0000971-D*
[LG03500(ALL)01/95]
This light comes on when the parking brake is set, or if it is not
set, it comes on briefly when you turn the ignition to the
START position. It normally goes off shortly after the engine
starts and you release the parking brake. If the light stays on
after you have fully released the parking brake, have the
hydraulic brake system serviced by your dealer or a qualified
service technician.
*
[LG03700(ALL)05/95]
RWARNING
The BRAKE light indicates that the brakes may not be
working properly. Have the brakes checked immediately.
File:cdlgz.ex
Update:Fri Feb 23 11:08:00 1996

Warning Lights and Gauges
65
%*
[LG22400(ALL)02/95]
Anti-lock Brake System Warning Light (If equipped)
[LG22500(ALL)05/94]
Your vehicle may have an Anti-lock Brake System feature. If it
does, check the Anti-lock Brake System light each time you start
the engine. If it stays on longer than three (3) seconds, shut off
the engine and restart. If it stays on, that means the Anti-lock
Brake feature is not working and should be serviced
immediately to restore the benefits of the Anti-lock feature.
Normal braking is not affected unless the brake warning light is
also lit.
[LG22600(ALL)04/95]
The Anti-Lock Brake System has self-check capabilities. As
described above, the system turns on the anti-lock light each
time you start your engine. After the engine is started and the
anti-lock light turns off, the system performs another test the
first time the vehicle reaches 5 mph (8 km/h) (between 12 and
25 mph [20 and 40 km/h] for vehicles equipped with the
traction control system). The system turns on the ABS pump
motor for approximately 1/2 second. At this time, a mechanical
noise may be heard and felt. This is a normal part of the
self-check feature. If a malfunction is found during this check
the anti-lock light will come on.
[LG22700(ALL)01/95]
6 pica art:0001210-AFile:cdlgz.ex
Update:Fri Feb 23 11:08:00 1996

88
%*
[SC09200(ALL)06/95]
Accelerating With the Speed Control Operating
*
[SC09300(ALL)05/95]
You can use the accelerator pedal to speed up momentarily.
When you take your foot off the accelerator, the vehicle will
return to the set speed.
*
[SC09400(ALL)01/95]
Resetting the Speed Control
*
[SC09410(ALL)03/95]
To reset the speed control to alower speed, use one of the
following procedures:
*
[SC09415(ALL)03/95]
n
COASTÐ Press and hold the COAST switch. Release the
switch when the vehicle slows down to the desired speed.
[SC09420(ALL)05/94]
n
Tap the brake pedal. When the vehicle attains the desired
speed, press the SET ACC switch and release it immediately.
[SC09427(ALL)05/94]
n
TAP-DOWNÐ Press and then quickly release the COAST
switch. Each time you ªtapº the switch, the set speed will
decrease by 1 mph (1.6 km/h).
*
[SC09430(ALL)05/95]
If vehicle speed is reduced below 30 mph (50 km/h) by any of
the above methods, then you must manually accelerate to a
speed over 30 mph (50 km/h) and reset the system.
*
[SC09435(ALL)03/95]
To reset the speed control toa higher speed, follow one of
these procedures:
[SC09440(ALL)05/94]
n
ACCÐ Press and hold the SET ACC switch. Release the
switch when the vehicle has accelerated to the desired speed.
[SC09445(ALL)03/95]
n
Depress the accelerator pedal. When the vehicle attains the
desired speed, press and release the SET ACC switch.
[SC09452(ALL)05/94]
n
TAP-UPÐ Press and then quickly release the SET ACC
switch. Each time you ªtapº the switch, the set speed will
increase by 1 mph (1.6 km/h).
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

Steering Column Controls
89
[SC09500(ALL)05/95]
To Cancel Speed Control
[SC09600(ALL)05/95]
Speed control can be cancelled at any time by pressing the
brake pedal slightly. After cancelling, you can return to the
speed you set by pressing the RES switch, or set a new speed
by pressing the SET ACC or COAST switch.
%*
[SC10900(ALL)06/95]
Cancelling and Resuming a Set Speed
[SC11000(ALL)05/95]
If you press the brake pedal, the speed control is suspended.
You can return to the set speed by pressing the RES switch, as
long as you did not press the OFF switch. You must be driving
at least 30 mph (50 km/h).
*
[SC11300(ALL)05/95]
Your vehicle will gradually return to the previously set speed
and then maintain it.
%*
[SC11360(ALL)05/95]
To Turn Off the Speed Control System
*
[SC11370(ALL)05/95]
Press the OFF switch.
*
[SC11380(ALL)05/95]
In addition, the speed control is turned off each time you turn
the vehicle off.
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

Features
111
*
[FV19000(ALL)01/93]
Floor Mats
[FV19100(ALL)01/95]
Positive retention floor mat (If equipped)
(Standard in Canada)
*
[FV19200(ALL)01/95]
Position the floor mat in the footwell. Place the mat eyelet over
the pointed end of the retention post from the rear and rotate
forward to install. Adjust the floor mat position to allow proper
operation of accelerator pedal, brake pedal and clutch pedal.
[FV19300(ALL)01/95]
17-1/2 pica
art:0001344-A
The positive retention floor mat
[FV19400(ALL)01/95]
To remove, lift the floor mat just forward of the retention post
and rotate it rearward to disengage it from the retention post.
File:cdfvz.ex
Update:Fri Feb 23 11:06:10 1996

138
*
[DR00900(ALL)01/95]
Putting Your Vehicle in Gear
[DR00915(ALL)05/95]
You must push in the thumb button to move the gearshift to
the position you choose.
*
[DR00917(ALL)05/95]
RWARNING
Hold the brake pedal down while you move the gearshift
lever from position to position. If you do not hold the
brake pedal down, your vehicle may move unexpectedly
and injure someone.
*
[DR00918(ALL)03/95]
To operate:
*
[DR00919(ALL)01/95]1.
Start the engine.
*
[DR00920(ALL)01/95]2.
Depress and hold the brake pedal.
*
[DR00921(ALL)01/95]3.
Move the gearshift lever out of P (Park).
%*
[DR00923(ALL)04/95]
Your vehicle is equipped with a Brake Shift Interlock safety
feature. This feature prevents the gearshift from being moved
from the P (Park) position until the brake pedal is depressed.
This feature is active when the ignition is in the ON position. If
the gearshift lever CANNOT be moved from P (Park) with the
brake pedal depressed:
*
[DR00924(ALL)01/95]1.
Turn the engine off and remove the ignition key.
[DR00925(ALL)05/94]2.
With the parking brake applied and the brake pedal
depressed, insert a screwdriver about 2" (5 cm) into the
square opening to the right of the gearshift at the base of the
console.
[DR00926(ALL)05/94]3.
Rotate the screwdriver point rearward.
[DR00927(ALL)02/94]4.
Push and hold the thumb button and move the gearshift.
[DR00928(ALL)02/94]5.
Remove the screwdriver when the gearshift moves from the
P (Park) position.
File:cddrz.ex
Update:Fri Feb 23 11:04:09 1996

Driving Your Mystique
139
[DR00929(ALL)01/95]
13-1/2 pica
art:0001264-C
Overriding the brake shift interlock
*
[DR00931(ALL)04/95]
The console-mounted gearshift will lock when you turn the key
to the LOCK position. When the gearshift is in any position
except P (Park), the ignition key cannot be turned to LOCK or
removed from the steering column. TO REMOVE THE KEY, the
gearshift levermustbe in P (Park).
*
[DR00935(ALL)11/94]
Once the gearshift is secure in the desired position, release the
brake pedal and use the accelerator as necessary.
File:cddrz.ex
Update:Fri Feb 23 11:04:09 1996

140
[DR01100(ALL)05/94]
13-1/2 pica
art:0000492-D
Console-mounted automatic transaxle shift control lever
%*
[DR01600(ALL)01/95]
R (Reverse)
*
[DR01700(ALL)02/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR01725(ALL)01/95]
N (Neutral)
[DR01750(ALL)11/94]
In N (Neutral), the wheels of the transaxle are not locked. Your
vehicle will roll freely, even on the slightest incline, unless the
parking brake or brakes are on.
*
[DR01800(ALL)01/95]
Driving
[DR01825(ALL)02/94]
Your vehicle's gearshift is console-mounted on the floor. The
Transaxle Control Switch (TCS) is located on the gearshift
handle. The transaxle control indicator light (OD OFF) is located
on the instrument panel. You can put the gearshift lever in any
of the several positions.
[DR01850(ALL)05/94]
The OD OFF light is off (not illuminated) during normal vehicle
operation. This allows the transaxle to upshift and downshift
from first through fourth gears. When the TCS is pressed, the
File:cddrz.ex
Update:Fri Feb 23 11:04:09 1996