1996 Lexus LS400 oil temperature

ENGINE
193
Gasolines containing alcohol
Gasohol is a mixture of gasoline and ethanol. If you use
gasohol in your Lexus, be sure that it is unleaded, has
an octane rating no lower than 87 and does not contain
more than 10% ethanol. Lexus does not recommend the
use of gasolines containing methanol.
If you use gasoline containing methanol, use only gasoline
meeting the requirements above and also containing less
than 5% methanol with cosolvents and corrosion inhibitors
for methanol.
NOTICE
Do not use gasohol other than stated above. It will
cause fuel system damage or vehicle performance
problems.
If driveability problems are encountered (poor hot
starting, vaporizing, engine knock, etc.),
discontinue its use.
Take care not to spill gasohol during refueling.
Gasohol may cause paint damage.
Fuel tank capacity
85 L (22.5 gal., 18.7 Imp. gal.)
FACTS ABOUT ENGINE OIL
CONSUMPTION
Functions of engine oil
Engine oil has the primary function of lubricating and cooling
the inside of the engine, and plays a major role in maintaining
the engine in proper working order.
Engine oil consumption
It is normal that an engine should consume some
engine oil during normal engine operation. The causes
of oil consumption in a normal engine are as follows.
Oil is used to lubricate pistons, piston rings and cylinders.
A thin film of oil is left on the cylinder wall when a piston
moves downwards in the cylinder. High negative pressure
generated when the vehicle is decelerating sucks some of
this oil into the combustion chamber. This oil as well as
some part of the oil film left on the cylinder wall is burned
by the high temperature combustion gases during the
combustion process.
Oil is also used to lubricate the stems of the intake valves.
Some of this oil is sucked into the combustion chamber
together with the intake air and is burned along with the
fuel. High temperature exhaust gases also burn the oil
used to lubricate the exhaust valve stems.

ENGINE
195
CHECKING THE ENGINE OIL LEVEL
With the engine at operating temperature and turned
off, check the oil level on the dipstick.
1. To get a true reading, the vehicle should be on a level
spot. After turning off the engine, wait a few minutes for the
oil to drain back into the bottom of the engine.
2. Pull out the dipstick, and wipe it clean with a rag.
3. Reinsert the dipstick and push it in as far as it will go, or
the reading will not be correct.

Add oilO.K.Too full
4. Pull the dipstick out and look at the oil level on the end.
If it is between the full line () and the low line (), it is O.K.
If the oil level is below or only slightly above the low
line, add engine oil of the same type as already in the
engine.

ENGINE
196Remove the oil filler cap and add engine oil a little at a time,
checking the dipstick. The approximate quantity of oil
needed to fill between the low line and the full line on the
dipstick is indicated below for reference.
When the level reaches within the correct range, return the
filler cap and turn the cap clockwise until you hear a click.
Oil quantity. L (qt., Imp. qt.) 1.5 (1.6, 1.3)
NOTICE
Avoid overfilling, or the engine could be damaged.
Check the oil level on the dipstick once again after
adding the oil.
Engine oil selection
Use API SH, Energy±Conserving II multigrade engine oil or
ILSAC multigrade engine oil.
Recommended viscosity (SAE):
SAE 5W±30 is the best choice for your vehicle, for good
fuel economy, and good starting in cold weather.
If you use SAE 10W±30 engine oil in extremely low
temperatures, the engine may become difficult to start,
so SAE 5W±30 engine oil is recommended.

ENGINE
197
Oil identification marks
API Service SymbolILSAC Certification Mark
Either or both API registered marks are added to some oil
containers to help you select the oil you should use.
The API Service Symbol is located anywhere on the
outside of the container.
The top portion of the label shows the oil quality by API
(American Petroleum Institute) designation such as SH.
The center portion of the label shows the SAE viscosity
grade such as SAE 5W±30. ªEnergy±Conserving IIº,
shown in the lower portion, indicates that the oil has
fuel±saving capabilities. Oils marked ªEnergy±Conserving
IIº will have higher fuel±saving capabilities than oils
marked ªEnergy±Conservingº.
The ILSAC (International Lubricant Standardization and
Approval Committee) Certification Mark is displayed on the
front of the container.
CHECKING THE ENGINE
COOLANT LEVEL

Reservoir capUpper lineLower line
Park the vehicle at a level spot and look at the
see±through coolant reservoir when the engine is cool.
The coolant level is satisfactory if it is between the
upper and lower lines on the tank. If the level is low, add
ethylene±glycol type coolant.
The coolant level in the reservoir will vary with engine coolant
temperature. However, if the level is on or below the lower
line, add coolant to bring the level up to the upper line.
Use only ethylene±glycol type coolant. It will prevent
freezing and corrosion. Neither supplemental inhibitors nor
additives are needed nor recommended. (For information on
ethylene±glycol coolant, see also ªEngine coolant selectionº
described below.)