1996 LAND ROVER DEFENDER ABS

STEERING
5
FAULT DIAGNOSIS REV: 05/99 Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box.
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes. Check condition of ball joints and the
lower steering column shaft universal joints for
wear
See Repair, Lower Steering Shaft and
Universal Joints
.
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
,See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing .
2.Check the steering hydraulic damper function
See Steering Damper.
3.Check steering column universal joints for wear
and correct alignment
See Repair, Lower
Steering Shaft and Universal Joints
.4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod
See Steering Linkage Inspect
.
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll bar
See
FRONT SUSPENSION, Repair, Panhard Rod
,
See FRONT SUSPENSION, Repair, Radius
Arm
,See FRONT SUSPENSION, Repair,
Anti-Roll Bar
,See FRONT SUSPENSION,
Repair, Front Shock Absorber
.
6.Fit new radius arm bushes using NTC 6781. Fit
new nuts, bolts and washers.
7.If problem persists fit damper kit STC 288 - 90,
STC 290 - 110/130 (2 off front) and STC 289 -
90, STC 291 - 110 levelled, STC 292 - 110
unlevelled, STC 293 - 130 (2 off rear). Road test
vehicle.
8.Check the power steering box adjustments and
operation
See Overhaul, Power Steering Box.
9.Check the hub bearing end floats and determine
the condition of the hub bearings as applicable
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
.
10.Check the resistance and condition of the
swivels
See FRONT AXLE AND FINAL DRIVE,
Description and operation, Description
.
If problem is not diagnosed: Repeat checks
starting at 1.
11.Carry out a full steering geometry check
See
GENERAL SPECIFICATION DATA,
Information, Steering
.

57STEERING
8
FAULT DIAGNOSIS 4. DIRECTIONAL STABILITY
From 1. GENERAL STEERING:
1.Is directional stability concern when vehicle is
towing?
YES - Check towing/vehicle loading parameters
in Owner's Handbook.
NO - go to 3.
2.Is problem resolved?
YES - end
NO - continue.
3.Check condition of rear trailing link/chassis
bushes.
4.Is problem resolved?
YES - end
NO - continue.
5.Check condition of front and rear shock
absorbers. If necessary, change units in pairs,
side to side.
6.Is problem resolved?
YES - end
NO - continue.
7.Check steering damper
See Steering Damper
.
8.Is problem resolved?
YES - end
NO - continue.
9.Check wheel balance
10.Is problem resolved?
YES - end
NO - contact local technical office.POWER STEERING FLUID LEAKS
1.Is fluid level correct?
YES - go to 3.
NO - Refill or drain to correct level. Bleed
system, check for leaks
See Repair, Power
Steering System - Bleed.
2.Is problem resolved?
YES - end
NO - continue.
3.Are hoses or joints leaking? Check on full lock
with engine at 2000 rev/min.
YES - loosen and retorque joints.
NO - go to 6.
4.Does leak remain?
YES - change PAS pipe.
NO - end.
5.Does leak remain?
YES - suspect seal in component. Check and
replace as necessary.
NO - end.
6.Is oil escaping from filler cap?
YES - bleed system
See Repair, Power
Steering System - Bleed.
NO - go to 8.
7.Is oil still escaping from filler cap?
YES - go back to 1.
NO - end.
8.Is oil leaking from PAS pump?
YES - go to 10.
NO - continue.
9.Is oil leaking from PAS box?
YES - go to 10.
NO - end.
10.Clean unit, add tracer dye to system. Retest
11.Is oil still leaking?
YES - establish leak point. Repair or replace unit
as necessary.
NO - end.

57STEERING
10
REPAIR STEERING COLUMN NACELLE
Service repair no - 57.40.29
Remove
1.Disconnect battery.
2.Remove steering wheel
See Steering wheel.
3.Remove 5 screws and 2 self tapping screws and
lift top half of nacelle from steeering column
switch assembly.
4.Ease bottom half of nacelle from switch
gaiters/grommets. Remove lower nacelle.
Refit
5.Locate top half of nacelle in position and fit to
switch assembly gaiters/grommets.
6.Locate lower half of nacelle and loosely fit
retaining screws.
7.Ensure switch gaiters/grommets are correctly
located and nacelle is aligned with switch
assembly brackets.
8.Fully tighten screws.
9.Fit steering wheel
See Steering wheel.
10.Reconnect battery.DROP ARM
Service repair no - 57.50.14
Remove
1.Park vehicle on level surface and chock rear
wheels.
2.Raise vehicle and locate axle stands or use a
ramp.
3.Disconnect steering damper from drag link
See
Steering damper
.
4.Disconnect drag link ball joint from drop arm
using extractorLRT-57-018.
5.Mark drop arm and steering box for reassembly.
6.Bend back tabs on locking washer, slacken
retaining nut, but do not remove.
7.Fit extractorLRT-57-012and release drop arm
from steering box spline.

STEERING
1
OVERHAUL POWER STEERING BOX - ADWEST
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicleSee Repair,
Power Steering Box
. Mark drop arm and
steering box for realignment on assembly.
Remove drop arm using extractorLRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster.
11.Slide out sector shaft.

STEERING
5
OVERHAUL
Rack thrust pad and adjuster
43.Examine thrust pad for scores.
44.Examine adjuster for wear in pad seat.
45.Fit new sealing ring to rack adjuster.
Rack and piston
46.Examine for excessive wear on rack teeth.
47.Ensure thrust pad bearing surface is free from
scores and wear.
48.Ensure piston outer diameters are free from
burrs and damage.
49.Examine seal and ring groove for scores and
damage.
50.Fit new ring to piston. Warm nylon seal and fit to
piston.
51.Slide piston assembly into cylinder with rack
tube outwards.
Reassemble
NOTE: When fitting replacement oil seals
lubricate with recommended fluid and
ensure absolute cleanliness.
Sector shaft oil seal
52.Fit oil seal, lip side first.
53.Fit extrusion washer.
54.Fit dust seal, lipped side last.
55.Fit circlip.
Fitting valve and worm assembly
56.Refit original shims and inner bearing cup. Use
Petroleum Jelly to aid assembly.
NOTE: If original shims are not used, fit
shims of 0.76 mm thickness.
57.Fit inner cage and bearings assembly.
58.Fit valve and worm assembly.
59.Fit outer cage and bearings assembly.
60.Fit outer bearing cup.

FRONT SUSPENSION
1
DESCRIPTION AND OPERATION DESCRIPTION
The front suspension design allows maximum wheel
travel and axle articulation providing good ground
clearance without loss of traction or directional
stability.
Long radius arms are fitted to the front axle and
provide maximum axle articulation which is vital for off
road performance. The radius arms are secured to
fabricated mounting brackets welded to the front axle.
Flexible rubber bushes are used on a stem end joint
to secure the rear of the radius arms to mountings on
the chassis cross member.
A panhard rod, which ensures that the front axle
remains centrally located, is fitted transversely and
also uses ferrule rubber bush mountings at both axle
and chassis locations.Two rubber bearing bushes, with retaining straps,
secure the rear of the anti-roll bar to the chassis
mountings, while bushed links support the front of the
bar to the front axle.
Conventional long travel coil springs and hydraulic
shock absorbers are used to control body movement
in all conditions. The shock absorbers are secured to
fabricated towers which are bolted to the chassis. The
upper and lower fixings use a single location stud with
flexible rubber bushes, support washers and securing
nuts. Retaining plates are used to secure the coil
springs to the fabricated towers and axle mountings.
Rubber bump stops are fitted underneath the chassis,
adjacent to the front road springs, and prevent
possible damage that could occur should there be
excessive axle to chassis movement.
Front suspension
1.Panhard rod
2.Radius arms
3.Coil springs
4.Shock absorber
5.Anti-roll bar

60FRONT SUSPENSION
2
REPAIRREV: 05/99
6.Remove fixings, radius arm to axle.
7.Lower radius arm front end to clear axle and
remove from vehicle.
8.Using suitable length of steel tubing, press out
flexible bushes.
Refit
9.Press in replacement bushes.
CAUTION: When pressing in new bushes
press on outer edge of bush and not
rubber inner.
10.Fit radius arm to axle mounting.
11.Fit track rod at ball joint.
12.Fit radius arm to chassis. Tighten bolts to
176
Nm (130 lbf/ft).
13.Fully tighten radius arm to axle fixings to197 Nm
(145 lbf/ft).
14.Fit road wheel, remove chassis stands and jack.
Tighten wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
FRONT SHOCK ABSORBER
Service repair no - 60.30.02.
Remove
1.Loosen road wheel retaining nuts.
2.Support chassis on stands and remove road
wheel.
3.Support axle weight with jack.
4.Remove shock absorber lower fixing and
withdraw cupwasher, rubber bush and seating
washer.
5.Remove four shock absorber bracket fixings.
6.Withdraw shock absorber and bracket assembly.
7.Withdraw lower seating washer, rubber bush and
cupwasher.
8.Remove fixings, shock absorber to mounting
bracket.
9.Withdraw mounting bracket.
10.Lift off top seating washer, rubber bush and
cupwasher.

FRONT SUSPENSION
3
REPAIR REV: 05/99 Refit
11.Assemble shock absorber components.
12.Position shock absorber, complete with bracket
and secure with 4 fixings.
13.Secure shock absorber lower fixing.
14.Fit road wheel, remove chassis stands and jack.
Tighten wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
FRONT ROAD SPRING
Service repair no - 60.20.11.
Remove
1.Remove front shock absorber
See Front
shock absorber
.
CAUTION: Avoid over stretching brake
hoses. If necessary, loosen hose
connector locknuts to allow hoses to
follow axle.
2.Lower axle sufficient to free road spring.
3.Withdraw road spring.
4.Withdraw shock absorber bracket securing ring.
Refit
5.Fit shock absorber bracket retaining ring. Retain
in position with a nut.
6.Position road spring and raise axle.
7.Remove nut retaining securing ring.
8.Fit front shock absorber
See Front shock
absorber
.