1996 LAND ROVER DEFENDER wheel

86ELECTRICAL
10
REPAIR Refit
12.Fit alarm indicator light into fascia panel and
reconnect plug lead.
13.Reconnect speedometer cable and fit instrument
panel to fascia cowl.
14.Fit steering wheel
See STEERING, Repair,
Steering wheel.
15.Reconnect battery negative lead.
16.Fit battery access cover.
17.Fit LH seat cushion.ALARM SYSTEM FUSE
Service repair no - 86.77.04
Remove
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery negative lead.
NOTE: Operation 6 needs to be carried out
within 15 seconds to avoid activating
battery backed-up alarm sounder, if fitted.
NOTE: If an alarm sounder without battery
back-up is fitted, it is not necessary to
disconnect battery.
7.Remove steering wheel
See STEERING,
Repair, Steering wheel.
8.Remove 4 screws securing instrument panel to
fascia cowl
See INSTRUMENTS, Repair,
Instrument panel.
9.Pull instrument panel away from fascia and
disconnect speedometer cable, main harness
multi-plugs, alarm LED plug lead, heated rear
screen leads, gearbox oil temperature lead and
immobiliser warning light lead.
10.Remove instrument panel.
11.Remove alarm system 15 amp (blue) fuse from
holder located behind starter switch.

ELECTRICAL
11
REPAIR REV: 05/99 Refit
12.Fit new fuse.
13.Position instrument panel to fascia cowl area
and reconnect immobiliser warning light leads,
gearbox oil temperature lead, heated rear screen
leads, alarm LED plug lead, main harness
multi-plugs and speedometer cable,
14.Secure instrument panel to fascia cowl with 4
screws
See INSTRUMENTS, Repair,
Instrument panel.
15.Fit steering wheelSee STEERING, Repair,
Steering wheel.
16.Reconnect battery negative lead.
17.Fit battery access cover.
18.Fit LH front seat cushion.GENERATOR
Service repair no - 86.10.02
Remove
1.Disconnect battery.
2.Remove drive belt
See Auxiliary drive belt.
3.Unscrew 3 fixings, remove heat shield from rear
of generator, and disconnect electrical leads
from generator.
4.Remove generator bottom fixing bolt.
5.Remove long through bolt from top fixing and lift
generator from engine.
Refit
6.Fit generator to engine mounting bracket and
secure with top and bottom fixing bolts.
7.Connect electrical leads.
8.Fit heat shield.
9.Fit drive belt
See Auxiliary drive belt; Refit.
10.Reconnect battery.

86ELECTRICAL
12
REPAIR AUXILIARY DRIVE BELT
Service repair no - 86.10.03
NOTE: If cast lines on tensioner arm and
tensioner spring case are aligned, a new
drive belt must be fitted.
Remove
1.Disconnect battery.
2.Remove fan cowl
See COOLING SYSTEM,
Repair, Fan cowl.
3.Apply ring spanner to tensioner pulley retaining
bolt.
4.Turn spanner to release pulley tension from belt.
5.Detach belt from pulley.
6.Release tensioner.
7.Complete removal of belt. Mark direction on belt
if refitting.
Refit
8.Using ring spanner, release pulley tensioner and
fit new drive belt.
9.Remove ring spanner, drive belt will
automatically tension.
10.Fit fan cowl
See COOLING SYSTEM, Repair,
Fan cowl.
STARTER MOTOR
Service repair no - 86.60.01
Remove
1.Disconnect battery.
2.Disconnect electrical leads from starter solenoid.
3.Remove 3 fixings securing starter motor to
flywheel housing.
4.Withdraw starter motor.
Refit
5.Locate starter motor and secure to flywheel
housing.
6.Reconnect electrical leads to starter solenoid.
7.Reconnect battery.