1996 LAND ROVER DEFENDER lock

STEERING
1
ADJUSTMENT POWER STEERING BOX - ADJUST
Service repair no - 57.35.01
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake brake, chock wheels and Jack
up front of vehicle until wheels are clear of
ground.
2.Support chassis front on axle stands.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn
See Fault diagnosis,
Stiff Steering Checklist
.
5.Centralise steering box
See Centralise
Steering Box
.
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned
See Repair,
Steering Wheel
.
6.Adjustment is obtained by rocking the drop arm
about centre whilst an assistant slowly tightens
the steering box adjuster screw.
7.Tighten locknut when all backlash has been
removed.8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link and tighten to
40 Nm (30
lbf/ft).
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle
See Fault diagnosis, Road
Test Procedure
.
Drag link adjust
1.RH drive vehicles - if steering wheel is to right,
drag link is too long. If steering wheel is to left
drag link is too short.
LH drive vehicles - if steering wheel is to right,
drag link is too short. If steering wheel is to left
drag link is too long.
2.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
Service repair no - 57.35.05
LH drive vehicle
1.Disconnect drag link from drop arm
See Repair,
Drag link and drag link ends
.
2.Turn steering wheel on full RH lock.
3.Turn steering wheel back exactly two turns.
4.Fit drag link
See Repair, Drag link and drag
link ends
.
RH drive vehicle
1.Repeat operation for LH drive vehicle but turn
steering wheel on full LH lock.

57STEERING
2
ADJUSTMENT STEERING LOCK STOPS
Service repair no - 57.65.03
Check
1.Measure clearance between tyre wall and radius
arm at full lock. This must be not less than 20
mm.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check clearance between tyre wall and radius
arm on each lock.
NOTE: Alternatively lock stop adjustment
may be carried out using following
procedure.
Check
1.Measure stop bolt protrusion 'A'. Refer to table
for correct setting.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check wheel position at full lock.LOCK STOP SETTINGS
Tyre & wheel size - alloys
Make Size Setting
BF Goodrich Mud Terrain 265 59,7 mm
Goodyear GT+4 235 55,7 mm
Michelin M+S 4x4 235 54,2 mm
Tyre & wheel size - steel
Make Size Setting
Goodyear 205 52,2 mm
Michelin 205 52,2 mm
Avon 7.50 56 mm
Michelin 7.50 56 mm
Goodyear 7.50 56 mm

STEERING
3
REPAIR REV: 05/99
NOTE: The steering column is a non
serviceable component and can only be
serviced as a complete assembly.
25.Fit main support bracket and padding to steering
column and manoeuvre column into position in
vehicle.
26.Loosely secure main support bracket and
harness bracket to bulkhead.
27.Loosely fit clamp and rubber packing strip to
column.
28.Loosely secure lower end of column to lower
support bracket.
29.Loosely secure clamp bracket to main support
bracket.
30.Working inside vehicle cab, fit tie-bar to column
bracket and secure with single bolt to
22 Nm (16
lbf/ft).
31.Finally, tighten main support bracket, clamp
bracket, upper clamp, and lower support bracket
nuts and bolts. (M6 bolts
9 Nm (6 lbf/ft),M8
bolts
22 Nm (16 lbf/ft).
32.Fit brake pedal boxSee BRAKES, Repair,
Brake pedal
.
33.Fit steering lock/switch in position and rotate
steering column inner shaft to line up slot with
switch plunger.
34.Secure lock to column with clamp and shear
bolts. Evenly tighten bolts but do not shear them.
35.Temporarily fit steering wheel and operate
switch and lock mechanism several times to
ensure it functions correctly.
36.Fully tighten switch retaining bolts until heads
shear.
37.Connect electrical leads to rear of switch. Fit
alarm system passive coil, if applicable.
See
ELECTRICAL, Repair, Vehicle immobilisation
and alarm system
.
38.Fit switch assembly on steering column and
tighten clamping screw.
39.Connect switch assembly multi-plugs and
electrical leads to main harness.
40.Offer up instrument panel, connect speedometer
cable, multi-plugs and electrical leads to main
harness. If applicable, fit vehicle alarm system
connections.
See ELECTRICAL, Repair,
Vehicle immobilisation and alarm system
.
41.Secure panel with 4 screws.
42.Locate top half of nacelle in position and fit to
switch gaiters/grommets.43.Fit lower half of nacelle and loosely tighten fixing
screws.
44.Ensure switch gaiters/grommets are correctly
located and fully tighten fixings.
45.Turn indicator cancelling ring so that slots are
vertical and lug with arrow points to the left, in
direction of indicator switch.
46.Fit steering wheel with finisher attachment lug at
bottom, ensuring that indicator cancelling forks
locate in cancelling ring slots.
47.Secure wheel with nut and new shake-proof
washer. Tighten to
43 Nm (32 lbf/ft).
48.Fit steering wheel decal.
49.If necessary, fit new universal joints to support.
Note that long joint is fitted to short length of
shaft and short joint to long end. Joints can only
be fitted one way to shaft.
50.With steering lock engaged and road wheels in
straight ahead position, align reassembly marks,
and fit collapsible shaft assembly with long leg of
shaft to steering box. Fit pinch bolts and tighten
to
25 Nm (18 lbf/ft).

57STEERING
4
REPAIR POWER STEERING BOX
Service repair no - 57.10.01
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
General precautions
·Whenever any part of system, is removed or
disconnected, utmost cleanliness must be
observed.
·Disconnected ports and hoses must be
plugged to prevent ingress of dirt. If metal
sediment is found in system, establish cause,
rectify and flush system.
·Do not start engine until reservoir is full as
pump will be damaged.
·Metric pipe fittings are used with 'O' ring pipe
ends on fittings to steering box.
·Follow normal 'O' ring replacement procedure
whenever pipes are disconnected.
·Ensure compatible metric components when
fitting replacement pipes.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition.
NOTE: When drag link is disconnected
from steering box, travel available at
steering wheel to each full lock is not
equal.
Remove
1.Site vehicle on level surface.
2.Apply park brake, chock rear wheels, raise
vehicle and locate axle stands. Alternatively,
raise vehicle on a hoist.
3.Remove road wheel.
4.Remove panhard rod
See FRONT
SUSPENSION, Repair, Panhard rod
.
5.Disconnect steering damper from drag link.
6.Disconnect drag link from drop arm, see J6305
on opposite page, using a suitable extractor.
7.Slacken, but do not remove nut securing tie bar
to mounting arm.8.Remove 2 bolts securing tie bar to steering box
and move aside.
9.Remove filler cap from power steering fluid
reservoir.
10.Position suitable container under steering box.
11.Disconnect feed and return pipes from steering
box and drain fluid.
12.Plug open pipes and steering box ports to
prevent ingress of dirt. Refit fluid reservoir filler
cap.
13.Centralise steering
See Centralise steering
box
.
14.Remove pinch bolt securing lower shaft
universal joint to power steering box.
15.Remove 4 bolts and 2 tab washers securing
steering box to chassis side member.
16.Withdraw steering box.
17.Clean all mounting faces, unions etc. prior to
refitting.
Refit
18.Position steering box to chassis side member,
ensuring locating peg is engaged. Fit tab
washers and tighten bolts to
81 Nm (60 lbf/ft).
19.Fit pinch bolt and nut securing universal joint to
power steering box spline. Tighten to
25 Nm (18
lbf/ft).
20.Secure tie bar to mounting arm and steering box.
Tighten fixings to
81 Nm (60 lbf/ft),starting with
tie bar to mounting nut, then loosen fixings by
one complete turn.
21.Check steering box and adjust if necessary
See
Adjustment, Power steering box - adjust
.
22.Refit drag link to drop arm and tighten nut to
40
Nm (30 lbf/ft).
Fit new split pin to retaining nut.

STEERING
5
REPAIR REV: 05/99
23.Fit panhard rodSee FRONT SUSPENSION,
Repair, Panhard rod
.
24.Fit road wheels. Lower vehicle to ground and
tighten wheel nuts to correct torque:
Alloy wheels - 130 Nm (96 lbf/ft)
Steel wheels - 100 Nm (80 lbf/ft)
Heavy duty wheels - 170 Nm (125 lbf/ft)
25.Remove plugs and refit feed and return pipes to
steering box. Tighten 16mm thread to
20 Nm (15
lbf/ft),
14mm thread to15 Nm (11 lbf/ft).
26.Remove filler cap. Fill reservoir to oil level mark
on dipstick, using recommended fluid
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
.
27.Bleed power steering system
See Power
steering system - bleed
.
28.Recheck fluid level and replace cap.
29.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
30.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over uneven ground and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
31.Drive vehicle in a straight line on level ground
and stop.
32.Tighten tie bar to mounting nut to
110 Nm (81
lbf/ft).
33.Tighten tie bar to steering box fixings to81 Nm
(60 lbf/ft).
34.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
35.If necessary, reposition steering wheel
See
Steering wheel
.
36.Road test vehicle.

57STEERING
6
REPAIR POWER STEERING SYSTEM - BLEED
Service repair no - 57.15.02
1.Check that fluid level is at maximum level
See
MAINTENANCE , Under bonnet maintenance.
2.Run engine to normal operating temperature.
3.Recheck reservoir fluid level, top up if necessary
NOTE: During operations 4 to 6, maintain
maximum fluid level in reservoir. Do not
increase engine speed or move steering
wheel.
4.With engine at idle speed, slacken bleed screw.
When fluid seeps past bleed screw retighten
screw.
5.Check fluid level.
6.Clean away fluid around bleed screw.
7.Check hose connections, pump and steering box
for fluid leaks by holding steering on full lock in
both directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute to avoid overheating fluid and
possibly damaging seals.
8.Carry out road test.POWER STEERING FLUID RESERVOIR
Service repair no - 57.15.08
Remove
1.Position drain tin beneath reservoir.
2.Slacken mounting bracket clamp bolt and raise
reservoir to gain access to feed and return hose
retaining clips.
3.Slacken clips, disconnect hoses from reservoir,
allow fluid to drain.
4.Remove reservoir.
CAUTION: Plug connections to prevent
ingress of dirt.
CAUTION: Discard fluid drained from
system. Do not allow fluid to contact
paintwork, if spilled, remove fluid and
clean area with warm water.
Refit
5.Position reservoir, connect feed and return
hoses and tighten clips to
3 Nm (2 lbf/ft).
6.Fit reservoir in clamp, tighten clamp bolt.
7.Fill reservoir between upper mark and end of
dipstick with power steering fluid
See
MAINTENANCE , Under bonnet maintenance
.
8.Bleed power steering system
See Power
steering system - bleed
.

57STEERING
8
REPAIRREV: 05/99 LOWER STEERING SHAFT AND UNIVERSAL
JOINTS
Service repair no - 57.40.16
Remove
1.Remove vehicle bonnet.
2.Set road wheels and steering wheel in straight
ahead position.
3.Mark relationship of steering column inner shaft
to top universal joint.
4.Remove 2 bolts from top universal joint.
5.Remove lower bolt from bottom universal joint.
6.Slacken upper bolt of lower universal joint and
withdraw shaft.
7.Inspect upper and lower universal joints for wear
and excessive play, renew if necessary.
8.Inspect universal joints for stiffness, lubricate if
necessary.Refit
9.Fit universal joints so pinch bolt holes line up
with flat on shaft. Note that the long joint is fitted
to short length of shaft and short joint to long
end.
10.With steering lock engaged and road wheels in
straight ahead position, line up assembly marks.
11.Position shaft assembly onto steering column.
Move assembly up spline to enable lower
universal joint to fit onto steering box splines.
12.Align bolt holes with grooves in splines. Fit pinch
bolts and tighten to
25 Nm (18 lbf/ft).
STEERING WHEEL
Service repair no - 57.60.01
Remove
1.Set road wheels and steering wheel in straight
ahead position.
2.Prise decal from steering wheel pad.
3.Remove retaining nut and shakeproof washer.
Make alignment marks on column and wheel
pad.
4.Withdraw steering wheel from column spline.
Refit
5.Turn indicator cancelling ring so that slots are
vertical and lug with arrow points to the left, in
direction of indicator switch.
6.Ensure front road wheels are in straight ahead
position.
7.Fit steering wheel with finisher attachment lug at
the bottom, ensuring indicator cancelling forks
locate in cancelling ring slots. Align assembly
marks.
8.Secure wheel with retaining nut and new
shakeproof washer. Tighten to
43 Nm (32 lbf/ft).

STEERING
9
REPAIR REV: 05/99 STEERING COLUMN LOCK
Service repair no - 57.40.28
Remove
1.Disconnect battery.
2.Set road wheels in straight ahead position.
3.Remove steering wheel
See Steering wheel.
4.Remove instrument panel
See INSTRUMENTS,
Repair, Instrument panel
.
5.Remove steering column nacelle
See Steering
column nacelle
.
6.Note position of harness leads on back of starter
switch and disconnect lucars. If fitted, remove
alarm system passive coil from switch
See
ELECTRICAL, Repair, Vehicle immobilisation
and alarm system
.
7.Using a punch or stud extractor remove 2 shear
bolts securing steering lock/starter switch to
column.
8.Remove steering lock and collect 2 washers
between lock and clamp.
Refit
9.Fit steering lock/switch in position and line up
with switch plunger.
10.Secure lock to column with clamp and new shear
bolts. Evenly tighten bolts but do not shear them.
11.Temporarily fit steering wheel and operate lock
and switch mechanism to ensure it functions
correctly.
12.Fully tighten retaining bolts until heads shear.
13.Connect harness leads to rear of starter switch.
If applicable, fit alarm system passive coil
See
ELECTRICAL, Repair, Vehicle immobilisation
and alarm system
.14.Fit steering column nacelle
See Steering
column nacelle
.
15.Fit instrument panel
See INSTRUMENTS,
Repair, Instrument panel
.
16.Fit steering wheel
See Steering wheel.
17.Reconnect battery.