1996 FORD THUNDERBIRD clock

242 [SV19000(MBC )05/95]
RWARNING
Never remove the radiator cap or vent
plug while the engine is running or hot.
[SV19030( ALL)05/95]
Follow these steps to avoid personal injury that
can be caused by escaping steam or engine
coolant.
[SV19040(MBC )03/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the
radiator cap or vent plug.
[SV19145( ALL)03/95]
2. When the engine is cool, wrap a thick towel
around the cap and turn it slowly
counterclockwise to unscrew.
*
[SV19150( ALL)09/95]
3. Step back while the pressure releases.
[SV19160( ALL)12/94]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it, and remove it.
*
[SV19170(MBC )09/95]
5. Stand away from the radiator opening. Hot
steam may blow out or hot engine coolant
may even splash out.
*
[SV19190( ALL)09/95]
To find out how much engine coolant mixture
your vehicle's coolant system can hold, seeRefill
capacities for fluidsin the Index.
% [SV19200( ALL)06/95]
Add engine coolant only to the reservoir.If the
coolant level is low, add a 50/50 or appropriate
mixture of water and the type of engine coolant
that Ford specifies. You may add water by itself
only in an emergency, but you should replace it
with a 50/50 or appropriate mixture as soon as
possible.
*
[SV19300( ALL)01/95]
Have your dealer check the engine cooling
system for leaks if you have to add more than a
quart (liter) of engine coolant more than once a
month.
File:rcsvb.ex
Update:Mon Feb 19 10:46:54 1996

276
*
[SV46600( ALL)03/95]
Removing the headlamp bulb
*
[SV46700( ALL)01/95]
1. Make sure that the headlamp switch is in
the OFF position.
*
[SV46800( BC )02/95]
2. Lift the hood and find the bulb in the
headlamp socket.
*
[SV46900( BC )01/95]
3. Remove the electrical connector from the
bulb by grasping the wire with a quick pull
rearward.
*
[SV47100( BC )01/95]
4. Remove the retaining ring by turning it 1/8
of a turn to free it from the socket. Then
slide the ring off the plastic base.Keep the
ring.You must use it again to hold the new
bulb in place.
*
[SV47400( ALL)03/95]
Installing the headlamp bulb
*
[SV47600(MBC )02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV47800(MBC )08/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[SV47900( ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV48000(MBC )02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:rcsvb.ex
Update:Mon Feb 19 10:46:54 1996

278 % [SV48900( BCGV)06/94]Toremovethe high-mount brakelamp:
[SV49200( BC )01/89]
1. Slide the trim cover toward the front of the
vehicle to disengage the retaining clips.
[SV49500( BC )01/89]
2. Twist the socket counterclockwise and
remove from lamp.
[SV50015( BC )03/91]
3. Pull bulb out of socket.
[SV50100( BC )01/89]
4. Remove the retaining screw.
[SV50200( BC )01/89]
5. Lift the lamp above the carpet and slide
away from the rear window.
[SV50260( BC )05/94]
6. Replace the burned out bulbs.
*
[SV50300( BCGV)02/95]
Toinstallthe high-mount brakelamp:
[SV50400( BC )01/89]
1. Slide the lamp into slots, toward the rear
window.
[SV50700( BC )01/89]
2. Install the screw.
[SV51000( BC )01/89]
3. Push bulb into the socket.
[SV51300( BC )01/89]
4. Install the bulb and socket into the lamp and
twist socket clockwise until it locks.
[SV51500( BC )01/89]
5. Slide the trim cover toward rear of vehicle
to engage the retaining clips.
File:rcsvb.ex
Update:Mon Feb 19 10:46:54 1996

310 Index
Chime (continued)
safety belt............... 59
Circuit breakers
checking and replacing........ 273
see also fuses............. 264
Cleaning your vehicle
chrome and aluminum parts....... 6
engine compartment.......... 230
exterior................ 5
exterior lamps............. 84
fabric................ 123
headlamps............... 84
instrument panel............ 74
instrument panel lens.......... 90
interior lamps.............. 89
mirrors................ 124
plastic parts.............. 6
polishing................ 6
rustproofing.............. 6
safety belts............... 18
tail lamps............... 84
upholstery and interior trim...... 123
washing................ 5
wheels................ 256
Climate control system
air conditioning........... 74,77
heating............... 74,77
Clock................... 89
Cold engine starting............ 48
Compact disc radio (see Electronic sound
system)................ 132
Console, description........... 127
Coolant (see Engine coolant)
checking and adding......... 240
drain and flush............ 244
preparing for storage......... 290
proper solution............ 242
refill capacities............ 285
refill procedure............ 244
specifications............. 287
temperature gauge........... 66
File:rcixb.ex
Update:Thu Feb 15 12:06:08 1996