1996 FORD F SERIES MOTORHOME AND COMMERCIAL CHASSIS wheel

87 %
*
[RE22450( FM)03/94]
quarter page art:0020319-C
Lug nut tightening sequence
[RE23450( M)06/90]
q
Lower the vehicle until the tire touches the
ground, and tighten lug nuts in the same
sequence to the specifications shown in the
chart below.
[RE23550( M)06/90]
q
Finish lowering the vehicle and replace any
wheel covers, ornaments, or hub caps that
your vehicle has. Make sure that they are
snapped into place.
[RE23650( M)06/90]
q
Put the tire, jack, and wrench away. (Make
sure jack is securely fastened so it doesn't
rattle when you drive.)
*
[RE23675( M)05/95]
RWARNING
Make sure spare tires and jacking
equipment are stowed and secured in the
proper storage location.
[RE23750( M)06/90]
q
Unblock the wheels.
File:ltrem.ex
Update:Tue Jun 20 16:45:33 1995

88
*
[RE24100( EFM)06/93]
Retighten the wheel lug nuts to the specified
torque at 100 miles (160 km), and again at 500
miles (800 km) of new vehicle operation and at
the intervals specified in theMaintenance Schedule
and Recordbooklet.
*
[RE24200( ALL)10/89]
Also retighten to the specified torque at 500
miles (800 km) of operation after any wheel
change or any time the lug nuts are loosened.
*
[RE24301( ALL)05/95]
RWARNING
Failure to retighten wheel lug nuts at
mileages specified could allow wheels to
come off while the vehicle is in motion.
% [RE24395( M)08/90]
eight pica chart:0020726-AFile:ltrem.ex
Update:Tue Jun 20 16:45:33 1995

89
*
[RE24700( ALL)05/95]
Towing Your Vehicle
*
[RE24875( ALL)]
If you need to have your vehicle towed, contact
a professional towing service or, if you are a
member, your roadside assistance center.
Recommended towing options include wheel lift
towing or flat bed towing.
[RE24925( ALL)02/95]
half page art:0001463-AFile:ltrem.ex
Update:Tue Jun 20 16:45:33 1995

110
*
[SV02100( ALL)01/95]
q
Never get under a vehicle while it is
supported by a jack only. If you must work
under a vehicle, use safety stands.
*
[SV02200( ALL)01/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02500( ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02600( ALL)03/95]
Working with the engine off:
*
[SV02650( E M)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02700( ALL)03/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV02725( ALL)03/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02750( ALL)03/95]
Working with the engine on:
*
[SV02785( E M)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02795( E M)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02900( ALL)02/95]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
File:ltsvm.ex
Update:Tue Jun 20 16:44:35 1995

130
*
[SV26150( ALL)05/95]
RWARNING
Improperly inflated tires can affect vehicle
handling and can fail suddenly, possibly
resulting in loss of vehicle control.
%*
[SV26200( ALL)02/95]
Tire Inspection and Maintenance
*
[SV26300( ALL)02/95]
Inspect the tire treads, and remove stones, nails,
glass or other objects that may be wedged in the
tread grooves. Check for holes or cuts that may
permit air to leak from the tire, and make the
necessary repairs.
*
[SV26400( ALL)10/89]
Inspect the tire side walls for cuts, bruises and
other damage. If you suspect internal damage to
the tire, have it demounted and checked. You
may need to repair or replace it.
*
[SV26410( ALL)11/89]
Wheel Inspection and Maintenance
*
[SV26420( ALL)11/89]
Check for damage that would affect the runout
of the wheels. Wobble or shimmy will eventually
damage the wheel bearings.
*
[SV26430( ALL)06/93]
Front wheel bearings require periodic repacking
and adjustment as specified in theMaintenance
Schedule and Recordbooklet. Loose or worn front
wheel bearings tend to let the vehicle wander or
shimmy, and can eventually cause excessive tire
wear.
*
[SV26435( ALL)06/95]
Whenever a wheel is removed and then
re-installed, always remove any corrosion that
may be present on the mounting surface of the
wheel and/or the surface of the hub, drum or
rotor that contacts the wheel.
File:ltsvm.ex
Update:Tue Jun 20 16:44:35 1995

131
*
[SV26440( ALL)05/95]
RWARNING
Installing wheels without good
metal-to-metal contact at the wheel
mounting surface can cause the wheel lug
nuts to loosen and could allow the wheel
to come off while the vehicle is in motion.
*
[SV26445( EFM)05/90]
RWARNING
Also retighten at 500 miles (800 km) after
any wheel change or any time the lug
nuts are loosened.
%*
[SV26500( ALL)02/95]
Tire Rotation
*
[SV26600( ALL)03/95]
Because your vehicle's front and rear tires
perform different jobs, they often wear
differently. To make sure your tires wear evenly
and last longer, rotate them at the mileage
shown in theMaintenance Schedule and Record
booklet which came with your vehicle.
[SV26615( M)05/91]
Your front tires should be rotated from side to
side. If the spare tire is used in the rotation, the
pattern should be: left front to right front; right
front to the spare and the spare to left front.
[SV26665( M)05/91]
NOTE: Do not rotate the dual rear tires.
File:ltsvm.ex
Update:Tue Jun 20 16:44:35 1995

132 %
*
[SV27300( ALL)04/95]
Replacing the Tires
*
[SV27400( ALL)05/95]
Replace any tires that show wear bands. When
your tire shows a wear band, it has only 1/16
inch (2 mm) of tread left.
*
[SV27500( ALL)10/89]
quarter page art:0060006-A
Wear band
*
[SV27600( ALL)01/95]
Because your vehicle's tires may wear unevenly,
you may need to replace them before a wear
band appears across the entire tread. Some spots
wear more heavily than others.
*
[SV27700( ALL)03/90]
Your wheels and tires are match-mounted for
improved ride. Before you begin to repair a tire,
mark the wheel and tire so that they are
properly aligned when remounted. This will
ensure that the tires will continue to give you
the same ride level.
*
[SV27851( ALL)01/95]
RWARNING
When replacing full size tires, never mix
radial, bias-belted, or bias-type tires. Use
only the tire sizes that are listed on the
tire pressure decal. Make sure that all tires
are the same size, speed rating, and
load-carrying capacity. Use only the tire
combinations recommended on the decal.
If you do not follow these precautions,
your vehicle may not drive properly and
safely.
File:ltsvm.ex
Update:Tue Jun 20 16:44:35 1995

135 [SV28725( M)05/95]
RWARNING
Aftermarket wheel assemblies may not be
compatible with your vehicle and should
not be used. Use of incompatible wheel
assemblies may result in equipment
failure and possible injury.
[SV28730( M)05/95]
A wheel or tire of the wrong size or type may
adversely affect such things as load carrying
capacity, wheel and bearing life, brake cooling,
speedometer/odometer calibration, stopping
ability, headlight aim, bumper height, vehicle
ground clearance, and tire or tire chain clearance
to the body and chassis. Replacement with used
wheels is not advised: they may have been
treated harshly or have high mileage, and they
could fail without warning.
[SV28732( M)05/95]
The use of wheels with load carrying limits
higher than the limits of the wheels originally
installed on your vehicle does not in itself
increase the GAWR or GVWR of the vehicle.
[SV28735( M)05/95]
RWARNING
Only wheel assemblies approved and
released by Ford Motor Company for your
vehicle model should be used.
[SV28745( M)05/95]
RWARNING
Alterations to the vehicle suspension or
steering by raising the chassis (i.e., use of
aftermarket ªlift kitsº) may adversely
affect vehicle handling and braking
performance.
File:ltsvm.ex
Update:Tue Jun 20 16:44:35 1995