1996 FORD EXPLORER brake light

Driving Your Explorer
267
*
[DR24950(ALL)03/95]
RWARNING
When parking, do not use the gearshift in place of the
parking brake. Turn the key to LOCK whenever you
leave your vehicle. Always set the parking brake fully
and make sure that the gearshift is securely latched in P
(Park) (automatic transmission) or in 1 (First) (manual
transmission). Never leave your vehicle unattended while
it is running. If you do not take these precautions, your
vehicle may move unexpectedly and injure someone.
[DR25015(ALL)03/93]
To release the parking brake, press the service brake pedal with
your right foot and hold the parking brake pedal down with
your left foot while you pull the parking brake release lever.
Lift your foot from the parking brake pedal after it is released.
*
[DR25050(ALL)01/93]
RWARNING
If the parking brake is fully released, but the Brake
System light remains on, have the brakes checked
immediately. They may not be working properly.
*
[DR25100(ALL)06/95]
The parking brake is not designed to stop a moving vehicle, but
you can use the parking brake to stop your vehicle in an
emergency if the normal brakes fail. However, since the parking
brake applies only the rear brakes, the stopping distance will
increase greatly and the handling of your vehicle will be
adversely affected.
%*
[DR25200(ALL)01/95]
Driving Under Special Conditions
%*
[DR25250(ALL)01/95]
Tips for Safe Driving
*
[DR25301(ALL)07/95]
As with any new vehicle, yours may drive and handle
differently from your previous vehicle. Use care until you
become accustomed to its various features and driving
characteristics.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

270
*
[DR27601(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
%*
[DR27651(ALL)01/95]
High water
*
[DR27675(ALL)06/92]
Never attempt to cross water that is fast flowing or of unknown
depth.
*
[DR27701(ALL)05/90]
Do not drive through flooded areas unless you are sure that the
water is below the bottom of the wheel hubs.
*
[DR27750(ALL)04/94]
If you must drive through high water, drive slowly. You may
have limited traction or wet brakes, so allow extra stopping
distance because your vehicle will not stop as quickly as usual.
*
[DR27801(ALL)01/95]
After you drive through the standing water, apply your brakes
gently several times as your vehicle moves slowly. This helps to
dry the brakes.
*
[DR27820(ALL)06/95]
NOTE: If the transmission and transfer case is submerged in
water, their fluids should be checked and changed, if
necessary.
*
[DR27825(ALL)03/93]
NOTE: All rear axle lube quantities must be replaced every
100,000 miles (160,000 km) or if the axle has been
submerged in water. Otherwise, the lube should not
be checked or changed unless a leak is suspected or
repair required.
*
[DR27850(ALL)11/89]
Rocking the vehicle
*
[DR27901(ALL)05/90]
For 4x4 vehicles, engage 4WD LOW, when the vehicle gets
stuck and try to drive away.
*
[DR27950(ALL)05/95]
If your vehicle gets stuck (for example, in mud or snow), you
may rock it out of the spot. Shift in a steady rhythm between
forward and reverse gears. Allow the transmission to fully
engage, then press lightly on the accelerator. Do not rock the
vehicle for more than a few minutes. This may overheat the
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

290
%*
[DR37800(ALL)07/95]
Safety Chains
[DR37925( X)03/93]
Located near the step bumper hitch ball position are two holes
in the underside of the hitch plate for a Class II trailer (max).
These holes may be used for safety chain attachment when
towing with the step bumper. Always use safety chains when
towing. Safety chains are used to retain connection between the
towing and towed vehicle in the event of separation of the
trailer coupling or ball. Cross the chains under the trailer tongue
and allow slack for turning corners. Connect the chain to the
hitch plate using a positive coupling, such as ªQuick Linksº,
with a strength rating of at least that of the safety chain rating.
[DR37950( X)12/92]
When using a frame mounted trailer hitch, do not attach the
safety chains to the step bumper. Attach the safety chains to the
frame mounted hitch using the recommendations supplied by
the hitch manufacturer.
%*
[DR38000(ALL)08/95]
Trailer Brakes
*
[DR38100(ALL)03/95]
Separate trailer brakes are required on most towed vehicles
weighing over 1,500 lb (680 kg).
*
[DR38200(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake system directly
to your vehicle's brake system. Your vehicle may not
have enough braking power and your chances of having
a collision greatly increase.
%*
[DR38300(ALL)06/95]
Trailer Lamps
*
[DR38400(ALL)11/89]
Make sure your trailer lamps conform to Federal and local
regulations.
*
[DR38425(ALL)03/91]
Class I and Class II Trailer Tow electrical wiring provides two
circuits (right hand and left hand) to operate trailer stop/turn
tail lamps. Each stop/turn circuit will operate one combination
stop/turn light bulb (# 1157, 3157, 2357, or 3357) on the trailer.
Never add more than one trailer light bulb to one circuit.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

292
*
[DR38925(ALL)08/95]
Servicing Your Vehicle If You Tow
*
[DR38950(ALL)08/93]
If you tow a trailer for a long distance, your vehicle will need
to be serviced more frequently than usual. Refer to the
Maintenance Schedule and Recordbooklet for additional
information.
[DR39000(ALL)08/95]
Trailer towing tips
*
[DR39100(ALL)11/89]
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
*
[DR39200(ALL)05/90]
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at the
bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
*
[DR39300(ALL)11/89]
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or
automatically controlled, when approaching a stop.
*
[DR39400(ALL)11/89]
For a good handling truck-trailer combination, the trailer tongue
load should be approximately 10-15% of the loaded trailer
weight.
*
[DR39500(ALL)05/95]
Make a thorough check of your equipment before starting out
on the road. After you have traveled about 50 miles (80 km)
stop in a protected area and double-check your hitch and
electrical connections. Also check trailer wheel lug nuts for
tightness.
*
[DR39600(ALL)11/89]
When turning, drive slightly beyond the normal turning point
so the trailer wheels will clear curbs or other obstructions.
[DR39750(ALL)01/95]
When stopped in traffic for long periods of time in hot weather,
place the gearshift selector lever in P (Park) to increase the
engine idle speed. This aids in engine cooling and air
conditioner efficiency. If the engine overheats, rotate the
function selector control knob to panel position to stop the
compressor and increase the engine speed for a short time.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

296
*
[RE00950(ALL)06/95]
RWARNING
Do not push-start your vehicle. You could damage the
catalytic converter. For further information, seeJumper
Cablesin the Index.
*
[RE01000(ALL)05/95]
RWARNING
To avoid damage or injury, follow these directions in the
order they are given. If in doubt, call for road service.
*
[RE01100(ALL)03/95]
Preparing Your Vehicle
*
[RE01200(ALL)03/95]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[RE01300(ALL)03/95]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[RE01400(ALL)04/95]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01500(ALL)03/95]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE01600(ALL)02/95]5.
Turn on the heater fan in both vehicles. Turning on the fan
helps protect the electrical system from voltage surges. Turn
off all other switches and lights in both vehicles to prevent
possible damage to either vehicle's electrical systems.
File:12unrex.ex
Update:Thu Feb 29 09:14:34 1996

Roadside Emergencies
299
*
[RE03400(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
*
[RE03500(ALL)1/96]
After the vehicle is started, let it idle for a while to let the
engine ªrelearnº its idle conditions. Drive it around for a while
with all electrical accessories turned off to let the battery
recharge. Driveability may be deteriorated slightly until all drive
modes are ªrelearned.ºYou may need to use a battery charger
to fully recharge the battery.
*
[RE03525( X)01/95]
If you need to replace your battery, seeBatteryin theServicing
Your Explorerchapter.
%*
[RE03600(ALL)03/95]
Changing a Tire
*
[RE03700(ALL)01/95]
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off the ignition, set
the parking brake, and turn on the hazard flashers.
%*
[RE03800(ALL)03/95]
The Conventional Spare Tire
[RE03915( X)10/94]
Your vehicle may be equipped with a conventional spare tire,
which you can use as a spare or as a regular tire. This spare tire
is identical to the other tires that come with your vehicle,
although the wheel may not match.
*
[RE03930(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
%*
[RE04000(ALL)03/95]
The Temporary Spare Tire
*
[RE04100(ALL)03/95]
You may have a high pressure temporary spare tire. This spare
tire is smaller than a regular tire and is designed for emergency
use only. Use it only when you get a flat tire and replace it as
soon as you can. This spare tire is marked with the words
ªTEMPORARY USE ONLYº so that you can easily identify it.
File:12unrex.ex
Update:Thu Feb 29 09:14:34 1996

314
[RE28400(ALL)05/91]
n
Disconnect the driveshaft at the rear differential and properly
support it under the vehicle.
[RE28500(ALL)01/95]
n
Mark the driveshaft and axle flanges to ensure proper
position when reconnecting the driveshaft. Refer to service
manual for proper driveshaft fastener torque specification.
(See theAccessorieschapter for information on ordering
service manuals.)
[RE28600(ALL)05/95]
RWARNING
When disconnecting/installing the driveshaft, the parking
brake must be set and the wheels blocked to ensure the
vehicle does not roll.
[RE28700(ALL)06/94]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[RE28720(ALL)12/91]
4x2ÐManualtransmission
*
[RE28740(ALL)03/95]
n
Release the parking brake.
[RE28750(ALL)01/95]
n
Place the transmission gearshift in the neutral position.
[RE28770(ALL)12/91]
n
Maximum speed is limited by towing equipment
manufacturer's recommendation, unlimited distance.
[RE29450( X)10/94]
CONTROL TRAC transfer case
*
[RE29500(ALL)03/95]
n
Release the parking brake.
[RE29600(ALL)01/95]
n
Place the transmission gearshift in the neutral position.
[RE29750( X)10/94]
n
Ensure the transfer case is in 2WD.
[RE29800(ALL)10/94]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument panel will be off when the 4WD switch is
in 2WD.
[RE29850(ALL)10/92]
For automatic transmissions:
[RE29900(ALL)10/94]
n
Maximum speed is 35 mph (56 km/h).
[RE30000(ALL)10/94]
n
Maximum distance is 50 miles (80 km).
File:12unrex.ex
Update:Thu Feb 29 09:14:34 1996

Servicing Your Explorer
349
%*
[SV13775(ALL)01/95]
Checking and Adding Engine Oil
*
[SV13800(ALL)03/95]
Since the proper amount of engine oil is important for safe
engine operation, check the oil using the dipstick each time you
put fuel in your vehicle. Remember the engine must be off, the
oil must be warm and the vehicle must be parked on level
ground.
%*
[SV13900(ALL)04/95]
Checking the engine oil level:
*
[SV14000(ALL)02/95]1.
Turn the engine off after it has warmed up and allow a few
minutes for the engine oil to drain back into the oil pan.
*
[SV14050(ALL)06/95]2.
Set the parking brake, making sure the gearshift is securely
latched in P (Park) or 1 (manual transmission).
*
[SV14100(ALL)02/95]3.
Open the hood. Protect yourself from engine heat.
*
[SV14200(ALL)03/95]4.
Locate the engine oil dipstick (highlighted in yellow) and
carefully pull it out of the engine.
*
[SV14300(ALL)01/95]5.
Wipe the dipstick clean and put it back into position, making
sure it is fully seated.
[SV14400(ALL)10/94]
7-1/2 pica art:0021256-B
Engine oil dipstick
File:15unsvx.ex
Update:Thu Feb 29 09:20:34 1996