1996 FORD ESCORT ECU

281
*
[SV01900(ALL)06/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000(ALL)06/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[SV02100(ALL)08/95]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[SV02200(ALL)06/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
[SV02250(ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeStarting your vehicle's fuel-injected
enginein the Index.
*
[SV02525(ALL)03/95]
Working with the engine off:
[SV02550(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in Park
(automatic transaxle) or First (manual
transaxle).
*
[SV02650(ALL)06/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV02675(ALL)06/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

282
*
[SV02700(ALL)03/95]
Working with the engine on:
*
[SV02825(ALL)04/95]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[SV02850(ALL)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV03000(ALL)02/95]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
%*
[SV03100(ALL)03/95]
Opening the Hood
%*
[SV03200(ALL)01/95]
1. Inside the vehicle, pull the hood release
handle located under the bottom left corner
of the instrument panel.
%*
[SV03300(ALL)02/95]
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the hood
at the center of the vehicle.
[SV03350(ALL)09/89]
3. Lift the hood and secure it in the open
position with the prop rod.
*
[SV04100(ALL)11/90]
When you close the hood, make sure the prop
rod is in its retainer and that the hood latches
securely.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

295 %
*
[SV13710(ALL)03/95]
Engine oils with anSAE 5W-30viscosity are
PREFERREDfor your vehicle. They provide the
best engine performance, fuel economy and
engine protection for all climates down to-15ÊF
(-25ÊC).
%*
[SV13750(ALL)03/95]
Synthetic engine oils which are CERTIFIED and
of the preferred viscosity may be used in your
engine. The engine oil and oil filter must still be
changed according to the maintenance schedule.
%*
[SV13775(ALL)01/95]
Checking and Adding Engine Oil
*
[SV13800(ALL)03/95]
Since the proper amount of engine oil is
important for safe engine operation, check the oil
using the dipstick each time you put fuel in
your vehicle. Remember the engine must be off,
the oil must be warm and the vehicle must be
parked on level ground.
%*
[SV13900(ALL)04/95]
Checking the engine oil level:
*
[SV14000(ALL)02/95]
1. Turn the engine off after it has warmed up
and allow a few minutes for the engine oil
to drain back into the oil pan.
*
[SV14050(ALL)05/94]
2. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park) (automatic transaxle) or 1 (First)
(manual transaxle).
*
[SV14100(ALL)02/95]
3. Open the hood. Protect yourself from engine
heat.
*
[SV14200(ALL)03/95]
4. Locate the engine oil dipstick (highlighted in
yellow) and carefully pull it out of the
engine.
*
[SV14300(ALL)01/95]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

312
*
[SV28900(ALL)01/95]
q
Make sure the chains are the right size for
your tires. Use only SAE Class ªSº chains.
Other types may damage your vehicle.
[SV29010(ALL)06/93]
q
Put the chains on the front tires tightly with
the ends held down securely. Retighten the
chains after driving 1/2 mile (0.8 km). Follow
the chain manufacturer's instructions.
*
[SV29020(ALL)05/95]
q
Do not drive faster than 30 mph (50 km/h)
or the chain manufacturer's recommended
speed limit, whichever is lower. Avoid
bumps, holes and sharp turns. If you can
hear the chains rub or bang against your
vehicle, remove the chains to prevent damage
to your vehicle.
*
[SV29030(ALL)11/94]
q
Tire chains may affect vehicle handling. Drive
carefully and avoid hard braking.
*
[SV29040(ALL)11/94]
q
Do not use chains on temporary spare tires.
They may damage the vehicle and the tire.
%*
[SV29100(ALL)04/95]
Cleaning the Wheels
*
[SV29120(ALL)05/95]
Wash the wheels with the same detergent you
use to wash your vehicle's body. Do not use
acid-based wheel cleaners, steel wool, abrasives,
fuel, or strong detergents. These substances will
damage protective coatings. Use tar and road oil
remover to remove grease and tar.
*
[SV29140(ALL)04/95]
NOTE: Before going to a car wash, find out if
the brushes are abrasive.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

315
%*
[SV29300(ALL)05/95]
Automatic Transaxle Fluid
*
[SV29310(ALL)03/95]
Under normal circumstances, you do not need to
check the fluid level of the transaxle, since your
vehicle does not use up transaxle fluid. Refer to
theMaintenance Schedule and Recordbooklet for
replacement intervals. However, if the transaxle
is not working properly Ð for instance, the
transaxle may slip or shift slowly, or you may
notice some sign of fluid leakage Ð the fluid
level should be checked.
*
[SV29335(ALL)01/95]
NOTE: If the vehicle has been operated for an
extended period at high speeds, driven
in city traffic during hot weather, or
has been pulling a trailer, the vehicle
should be turned off for about 30
minutes to allow the fluid to cool
before checking.
%*
[SV29340(ALL)02/93]
Checking the Automatic Transaxle Fluid
[SV29345(ALL)03/95]
It is preferable to check the transaxle fluid level
at normal operating temperature after
approximately 20 miles (32 km) of driving.
*
[SV29350(ALL)02/95]
With the vehicle on a level surface and the brake
pedal fully applied, start the engine and move
the gearshift selector through all of the gears.
Allow sufficient time for each position to engage.
Securely latch the gearshift selector in the P
(Park) position. Fully set the parking brake and
leave the engine running.
*
[SV29370(ALL)01/95]
Wipe off the dipstick cap and pull the dipstick
out. Wipe the indicator end clean. Put the
dipstick back into the filler tube and make sure
it is fully seated. Pull the dipstick out and read
the fluid level.
[SV29392(ALL)12/89]
When checking fluid at the normal operating
temperature, the fluid level should be within the
normal operating temperature marks on the
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

336
*
[SV40650(ALL)01/95]
High-Mount Brakelamp Bulb
[SV40655(ALL)08/95]
Removing the brakelamp bulb
[SV40660(E )06/94]
half page art:0000832-A
Location of the high-mount brakelamp (GT hatchback
brakelamp is on spoiler)
[SV40665(ALL)09/89]
1. Push in the center of each of the three
mounting clips and pry each clip out.
[SV40670(ALL)02/94]
2. Remove the high-mount brakelamp cover.
[SV40675(ALL)09/89]
3. Remove the socket that contains the
burned-out bulb and replace the bulb.
[SV40680(ALL)03/95]
Installing the brakelamp bulb
[SV40685(ALL)09/89]
1. Push the bulb socket into the lamp assembly.
[SV40690(ALL)09/89]
2. Secure the cover with the mounting clips.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

337 [SV40700(ALL)03/95]
Replacing the brakelamp on a luggage
compartment with spoiler
[SV40710(ALL)08/93]
half page art:0070200-A
Location of the high-mount brakelamp on spoiler
[SV40725(ALL)03/91]
1. Remove the two retaining screws and the
lens.
[SV40750(ALL)03/91]
2. Detach the socket from the housing and
remove the bulb.
[SV40775(ALL)03/91]
3. Replace the bulb and ease the socket back
into the housing.
[SV40800(ALL)03/91]
4. Replace the lens and secure with the
retaining screws.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

338 [SV40820(ALL)03/95]Replacing a brakelamp mounted on the
package tray in the rear window
[SV40825(ALL)08/93]
half page art:0070201-A
Location of the high-mount brakelamp in rear window
[SV40830(ALL)08/93]
1. Remove the two fastener clips and the
brakelamp assembly cover.
[SV40840(ALL)03/91]
2. Detach the socket from the housing and
remove the bulb.
[SV40850(ALL)03/91]
3. Replace the bulb and ease the socket back
into the housing.
[SV40860(ALL)08/93]
4. Replace the brake assembly cover and secure
with the two fastener clips.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995