1996 FORD E SERIES hood release

281
*
[SV02600( ALL)03/95]
Working with the engine off:
*
[SV02650( E M)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
[SV02700( ALL)06/95]
2. Remove the key from the ignition after you
turn the engine off.
[SV02725( ALL)06/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02750( ALL)03/95]
Working with the engine on:
*
[SV02785( E M)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02795( E M)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02900( ALL)02/95]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
*
[SV02950(BEF )03/95]
Opening the Hood
[SV03025( E )05/89]
1. Pull the hood release handle, located on the
left kick panel near the parking brake release
handle.
*
[SV03050(BEF )12/91]
2. While applying downward pressure on the
hood, push the hood latch handle located
behind the grille near the center front of the
vehicle to the left.
*
[SV03100( E )08/94]
3. Disconnect the hood support from the
retaining clip on the radiator support and
place it into the slot marked PROP in the
underside of the hood.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

282
*
[SV03300(BEF )03/91]
one third page art:0020333-A
Hood release handle
[SV03500( E )02/92]
quarter page art:0020336-D
Hood and support
*
[SV03800( E )08/94]
To close the hood, raise it so that the support
rod comes away from the slotted hole in the
hood. Place the support rod in its retaining clip
and close the hood with enough force to make it
latch. Be sure to oil the hood latch every six
months to maintain smooth operation.
*
[SV03900(BEF )05/90]
Always attempt to lift the hood after closing to
be sure it is securely latched.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

342
*
[SV46300(BEF )03/95]
Removing the headlamp bulb
*
[SV46400(BEF )01/95]
1. Make sure that the headlamp switch on the
instrument panel is in the OFF position.
[SV46550( E )04/95]
2. Lift the hood and fix in up position using
prop rod.
[SV46600( E )04/95]
3. Bend back slightly and lift up on the two
metal tabs while holding the lamp to vehicle.
This will release the lamp from the installed
position.
[SV46650( E )05/91]
one third page art:0020844-B
Removing/Installing the headlamp bulb
[SV46750( E )04/95]
4. Remove the bulb retaining ring by turning it
1/8 of a turn to free it from the socket. Then
slide the ring off the plastic base. Keep the
ring. You must use it again to hold the new
bulb in place.
[SV46850( E )04/95]
5. Carefully remove the bulb assembly from its
socket by gently pulling it rearward without
turning.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

Index 387
Heating (continued)
standard heater system......... 83
High beams
indicator light............. 77
operation............. 92,100
High-mount brakelamp
description.............. 343
replacing the bulb.......... 343
High-mount brakelamp:location...... 96
Hitch................. 237
Hood
latch location............. 281
release lever............. 281
working under the hood....... 280
Horn.................. 104
Hoses, checking............. 305
I
Identification Number, Vehicle (VIN).... 6
Idle, relearning......... 57,247, 280
Ignition
chime................. 56
positions of the ignition......... 55
removing the key............ 56
Indicator lights and chimes (see Lights) . . . 67
Infant seats (see Safety seats)...... 38,41
Instrument cluster............. 67
mechanical............... 69
Instrument panel
cleaning................ 97
lighting up panel and interior...... 94
location of components......... 81
registers................ 83
Interval wipers...........101±102
J
Jack
operation............250, 252
positioning.............. 252
File:ltixe.ex
Update:Wed Apr 17 08:36:26 1996