1996 FORD E SERIES tow

102
*
[SC04700( ALL)05/95]
Variable Interval Wipers
*
[SC04800( ALL)03/95]
In addition to two speed wipers, your vehicle is
equipped with wipers that you can set to
operate at varying intervals. For example, you
can set the interval so they wipe less often when
it drizzles or more often in heavier rain.
*
[SC04950( ALL)05/95]
one third page art:0020831-A
Interval wiper on turn signal lever
*
[SC05000( ALL)02/95]
To set the interval wipers, rotate the knob at the
end of the turn signal lever toward or away
from the instrument panel to the interval
operation you desire.
*
[SC05100( ALL)05/95]
Windshield Washer
*
[SC05200( ALL)05/95]
To clean the windshield, push in the end of the
wiper knob. For a constant spray, keep the knob
pushed in. After you release the knob, the
wipers operate for two to three cycles before
turning off (if wipers were off) or returning to
the interval selected.
*
[SC05300( ALL)01/95]
Do not try to clean the windshield when the
washer fluid container is empty or activate the
washers at any time for more than 15 seconds
continuously. This could damage the washer
pump system.
File:07ltsce.ex
Update:Wed Apr 17 08:47:45 1996

105
*
[SC06200(BEF )05/95]
Tilt Steering (If equipped)
*
[SC06300( ALL)06/95]
RWARNING
Never adjust the steering wheel when the
vehicle is moving.
*
[SC06500(BEF )01/94]
one third page art:0020089-C
Turn signal and tilt release wheel lever
*
[SC06700( ALL)04/95]
To change the position of the steering
column/wheel, pull the release lever on the
column toward you. Tip the steering wheel to
the desired position. Release the lever to lock the
steering wheel in place.
*
[SC07250( ALL)12/89]
Be sure the steering wheel locks in a notch. It is
not infinitely adjustable. Do not adjust the
steering wheel while the vehicle is in motion.
File:07ltsce.ex
Update:Wed Apr 17 08:47:45 1996

113
Features
*
[FV00401(BEF )02/95]
Your vehicle has a variety of features designed
for your comfort, convenience and safety. Read
this chapter to find out about standard and
optional features.
*
[FV00501( EF )05/90]
NOTE: For Stripped Chassis vehicles, see your
Body Builders manual for location and
operation of all items defined in this
section.
*
[FV00601(BEF )01/95]
Doors
%*
[FV01801(BEF )03/95]
Anti-theft front door lock knobs
*
[FV01901(BEF )10/89]
Anti-theft lock knobs are designed to preclude
unlocking the door by pulling up on the bullet
type lock knob. To unlock and open the front
door from the inside of the vehicle, pull on the
inside door handle.
[FV03401( E )04/95]
Side Double Doors (If equipped)
[FV03500( E )05/91]
To open the forward door of the side double
door from the inside, first unlock the door with
the lock plunger or the power lock switch. Now
reach into the depression in the door and pull
the release handle inward. Open the forward
side door from the outside by pulling the door
handle towards you.
[FV03600( E )03/91]
The rear side door cannot be opened until the
forward side door is open. With the forward
side door open, pull the release handle (from the
middle of the rear door pillar) to open the rear
side door.
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

119
*
[FV17701(BEF )02/95]
NOTE: The operating range of the remote
entry system can also be affected by
weather conditions (such as very cold
temperatures) or structures around the
vehicle (buildings, other vehicles, radio
and TV towers, etc.). Typical operating
range will allow you to be up to 33
feet (10 meters) away from your
vehicle.
*
[FV17801(BEF )03/93]
quarter page art:0020789-A
Opening the remote transmitter
*
[FV17901(BEF )02/95]
The transmitter can be snapped apart to replace
the batteries by twisting a thin coin between the
two halves of the transmitter. DO NOT TAKE
THE FRONT PART OF THE TRANSMITTER
APART. When installing the new batteries, be
sure to place the positive (+) side down as
marked. Snap the two halves back together.
*
[FV18001(BEF )02/95]
quarter page art:0020790-A
Replacing the batteries
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

126 [FV27901( E )12/91]
one third page art:0020224-CReclining bucket seat
%*
[FV31201( E )12/91]
Quick Release Rear Captain Chairs
[FV31301( E )12/91]
Second row
*
[FV31400( E )12/91]
To remove:
[FV31700( E )12/91]
1. Disengage the lap/shoulder safety belt from
the seat by inserting a key or similar device
into the slot in the detachable anchor and
lifting upward. Stow the tongue end of the
detachable anchor as shown.
[FV31901( E )02/92]
2. Pull the seat latch handle, located on the
right hand side of the seat base, and pull
seat toward the right hand side of vehicle to
disengage four pins from the floor mount.
[FV32001( E )12/91]
one third page art:0020915-A
Removing the quick release rear captains chair
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

127 [FV32101( E )12/91]
3. Remove the seat from the vehicle.
*
[FV32200( E )12/91]
To install the rear bucket seat:
[FV32400( E )12/91]
1. Lift the seat assembly into the vehicle and
position the seat to the floor mount.
[FV32600( E )02/92]
2. Engage the four seat pins into their
respective floor mount holes and push the
seat toward the left hand side of the vehicle
to fully engage.
[FV32700( E )02/92]
one third page art:0020916-B
Installing the quick release rear captains chair
[FV33001( E )12/91]
3. Push the seat latch handle downward to a
full stop. This locks the seat in position.
[FV33101( E )12/91]
4. Before you engage the safety belt, be sure it
is not twisted. Remove any twist, then insert
the tongue end of the detachable anchor into
the detachable anchor until you hear a
ªsnapº and feel the latch engage.
*
[FV33201( E )05/95]
RWARNING
Check to see that the seat is latched
securely in position. Keep floor area free
of objects that would prevent proper seat
engagement. Never attempt to adjust the
seat latch while the vehicle is in motion.
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

129 [FV33501( E )05/95]
two third page art:0020856-C
Rear seat shoulder safety belt Ð stowage (with seat
removed)
% [FV36101( E )02/92]
Quick Release Rear Passenger Seat
Assembly
% [FV36201( E )02/95]
Three Passenger and Four Passenger Bench
and Bed Seats
[FV36300( E )01/89]
To remove the seat assembly:
*
[FV36400( E )06/92]
1. Disengage the lap/shoulder safety belt from
the seat by inserting a key or screwdriver
into the slot in the detachable anchor and
lifting upward. Stow the tongue end of the
detachable anchor as shown in the
illustration.
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

131 [FV36600( E )05/95]
two third page art:0020856-C
Rear seat shoulder safety belt Ð stowage (with seat
removed)
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996