1996 FORD E SERIES clock

205
*
[DR10500( ALL)01/95]
P (Park)
*
[DR10600( ALL)03/94]
Always come to a complete stop before you shift
into P (Park). This position locks the
transmission and prevents the rear wheels from
turning. To securely latch the gearshift in the P
(Park) position, pull it toward you, push it
completely counterclockwise against the stop,
and then push it toward the instrument panel.
*
[DR10650( ALL)03/94]
The gearshift is securely latched in P (Park) if
you cannot rotate it in a clockwise direction
without lifting it toward you.
*
[DR10700( ALL)06/95]
RWARNING
Always set the parking brake fully and
make sure the gearshift is securely latched
in P (Park).
*
[DR10800( ALL)06/95]
RWARNING
Never leave your vehicle unattended
while it is running.
*
[DR11100( ALL)06/94]
Forced Downshifts
*
[DR11200( ALL)04/95]
To gain extra acceleration injOverdrive or
Drive (O/D OFF), push the accelerator to the
floor. The transmission will automatically
downshift to the appropriate gear: third, second
or first.
*
[DR11235( ALL)03/94]
Power Braking
*
[DR11275( ALL)03/94]
Increasing the engine speed above idle without
vehicle movement (such as holding the brake) in
a forward or reverse gear causes transmission
stall.
*
[DR11285( ALL)03/94]
NOTE: Continued operation in the stall
condition can result in transmission
overheat, malfunction or fluid
expulsion.
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996

248
*
[RE04275(BEF )05/95]
RWARNING
To avoid injury, never run the engine
with one wheel off the ground, such as
when changing a tire.
*
[RE04280(BEF )10/94]
Extended use of other than matching size spare
tires on a Traction-Lok axle could result in a
permanent reduction in effectiveness. This loss of
effectiveness does not affect normal driving and
should not be noticeable to the driver.
*
[RE05100(BEF )03/95]
Spare Tire Location
*
[RE05250( E )06/94]
The spare tire for your vehicle is stowed at the
rear under the frame (except cutaway and
stripped chassis models).
*
[RE05550( E )03/91]
To remove the spare tire:
[RE05625( E )03/93]
1. Open both of the rear doors. Remove the
access cover from the rubber strip found
behind the left door. Insert tapered end of
lug wrench or tip of jack handle through the
access hole. Turn counterclockwise until the
cable extends enough to allow the spare tire
to be pulled rearward from under the
vehicle.
*
[RE05700( E )10/94]
2. Slide the spare tire to the rear and remove
the retainer from the wheel.
*
[RE05850( E )10/94]
3. To stow the cable/retainer with spare
removed, turn jack handle wrench clockwise
until slack is removed.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

249 [RE05975( E )02/95]
three fourths page art:0020839-C
The spare tire location and assembly
*
[RE06050( E )03/91]
To stow spare tire:
*
[RE06150( E )10/94]
1. Insert the jack handle or lug nut wrench into
the actuator hole and turn counterclockwise
until the cable/retainer is extended for
insertion into the wheel.
*
[RE06200( E )10/94]
2. Install the retainer through wheel center
with valve stem facing up.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

250
*
[RE06250( E )12/91]
NOTE: Stow aluminum wheel and tire with
valve stem down.
*
[RE06350( E )10/94]
3. Rotate the handle clockwise to secure tire.
Continue until the lift mechanism ªslipsº.
*
[RE06400( E )03/91]
4. Check for proper seating against underbody
supports and retighten if necessary.
*
[RE15100(BEF )05/95]
RWARNING
Make sure the spare tire and jacking
equipment are stowed and secured in the
proper storage location.
*
[RE15200( ALL)03/95]
Preparing to Change the Tire
*
[RE15250( ALL)12/91]
NOTE: To lift your vehicle by other than the
front or rear jacking points, be sure to
use only hoist adapters with a wide
contact surface.
*
[RE15325( E M)03/95]
1. Make sure that your vehicle will not move
or roll. Put the gearshift in P (Park). Set the
parking brake and block the wheel that is
diagonally opposite the tire that you are
changing.
*
[RE15377( E )06/95]
When one of the back wheels is off the ground,
the transmission alone will not prevent the
vehicle from moving or slipping off the jack,
even if the vehicle is in P (Park). To prevent the
vehicle from moving when you change a tire, be
sure the parking brake is set, then block the
wheel (both directions) that is diagonally
opposite (other side and end of the vehicle) to
the tire being changed.
[RE15430(E )10/95]
RWARNING
If the vehicle slips off the jack, you or
someone else coule be seriously injured.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

252
*
[RE16900(BEF )10/89]
4. Loosen the wheel nuts by pulling up on the
handle of the lug nut wrench about one-half
turn (counterclockwise). Do not remove the
wheel lug nuts until you raise the tire off the
ground.
*
[RE16950(BEF )05/95]
Removing and Replacing the Tire
[RE17000( E )02/95]
1. Unfold the jack handle and lock into the
jack. Use the jack handle to slide the jack
under the vehicle.
*
[RE17175(BEF )05/95]
RWARNING
To avoid injury, never run the engine
with one wheel off the ground, such as
when changing a tire.
*
[RE17200(BEF )05/95]
RWARNING
To lessen the risk of personal injury, do
not put any part of your body under the
vehicle while changing a tire. Do not start
the engine when your vehicle is on the
jack. The jack is only meant for changing
the tire.
[RE17300(BEF )06/95]
2. Positioning the jack
[RE18501( E )01/89]
a. To raise a front or rear wheel, place the
jack as shown in the following
illustrations.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

254
*
[RE19100( E )08/91]
b. Turn the jack handle clockwise until the
wheel is completely off the ground.
*
[RE21151(BEF )10/92]
one third page art:0020939-B
[RE21400(BEF )06/95]
3. Remove the lug nuts with the lug nut
wrench.
[RE21500(BEF )06/95]
4. Replace the flat tire with the spare tire.
*
[RE21600( EF )06/95]
If your vehicle has dual rear wheels, there are
locating pins on the hubs and wheels with
corresponding holes. When you put the wheel
back on, make sure the pins are lined up with
the proper holes.
[RE21800( EF )06/95]
If your vehicle has single rear wheels, thread the
lug nuts on the wheel studs with the beveled
face toward the wheel. Use the lug nut wrench
to screw the lug nut snugly against the wheel
but do not tighten.
*
[RE21900( EF )01/89]
If your vehicle has dual rear wheels, thread the
two-element swiveling lug nut on the wheel
studs with the flange face toward the wheel. Use
the lug nut wrench to screw the lug nut snugly
against the wheel but do not tighten.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

255
*
[RE22000( EF )05/90]
quarter page art:0020310-A
Single rear wheel nut
*
[RE22100( EFM)05/90]
quarter page art:0020311-A
Dual rear wheel nut
*
[RE22200(BEF )01/95]
5. Lower the vehicle by turning the jack handle
counterclockwise.
[RE22300(BEF )06/95]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration.
%*
[RE22425( EF )05/90]
quarter page art:0020317-A
Lug nut tightening sequence
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

288 %
*
[SV06550(BEF )02/91]
Opening the Fuel Filler Door
*
[SV06600(BEF )10/94]
To open the fuel filler door of your vehicle, just
insert your finger in the divot and pull the door
open all the way.
[SV06675( E )03/91]
NOTE: For Stripped Chassis vehicles, see your
Body Builders manual for the proper
location of the fuel filler door.
%*
[SV06700( ALL)01/95]
Removing the fuel cap
*
[SV06750( ALL)01/95]
The proper instructions for removing the fuel
cap are as follows:
*
[SV06800( ALL)03/90]
q
Unscrew the fuel cap by exerting pressure on
the plastic lock bar and rotating the fuel cap
counterclockwise.
*
[SV06850( ALL)12/91]
q
Turn the fuel cap 1/2 to 3/4 of a turn until a
hissing sound is heard. Wait until the hissing
sound stops and then continue rotating
counterclockwise to remove the fuel cap.
*
[SV06900( ALL)03/93]
q
Make sure that you follow the above fuel cap
removal instructions and use caution. Such
caution will minimize the possibility of fuel
spraying during removal of the fuel cap.
*
[SV06950( ALL)03/91]
To replace and secure the fuel cap; place it in
position and rotate it clockwise until it clicks
(ratchets). Doing so will not damage or break
the fuel cap. The ratcheting mechanism allows
the fuel cap to be sealed without overtightening.
*
[SV06975( ALL)06/95]
If you lose the fuel cap, replace it with an
authorized Motorcraft or equivalent part.
%*
[SV07000( ALL)05/95]
RWARNING
If you do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly
in a collision.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996