1996 FORD CONTOUR battery

58
*
[LG03800(ALL)01/95]
Charging System Light
*
[LG03900(ALL)03/95]
This light indicates that your battery is not being charged and
that you need to have the electrical system checked.
[LG04100(ALL)01/95]
6 pica art:0000293-C*
[LG04300(ALL)05/95]
This light comes on every time you turn the ignition to the ON
or START position (engine off). The light should go off when
the engine starts and the alternator begins to charge.
*
[LG04400(ALL)01/95]
If the light stays on or comes on when the engine is running,
have the electrical system checked as soon as possible.
%*
[LG04800(ALL)02/95]
Engine Oil Pressure Warning Light
*
[LG04900(ALL)01/95]
This light indicates the engine's oil pressure, not the oil level.
However, if your engine's oil level is low, it could affect the oil
pressure. The light will come on briefly when you turn your
key to the START and ON position. The light should stay off
when the engine is running with normal oil pressure. If the
light comes on while the engine is running, you have lost oil
pressure and continued operation will cause severe engine
damage.
[LG05010(ALL)01/95]
6 pica art:0000294-BFile:cdlgo.ex
Update:Thu Jan 25 12:16:21 1996

86
%*
[SC05520(ALL)03/95]
Hazard Flasher
*
[SC05530(ALL)03/95]
The hazard flasher serves as a warning to other drivers to be
careful when approaching or passing your vehicle.
[SC05540(ALL)05/94]
10-1/2 pica
art:0001193-A
Using the hazard flasher switch
*
[SC05590(ALL)03/95]
The flashers work whether your vehicle is running or not. The
flashers work for up to two hours when the battery is fully
charged and in good condition without draining the battery
excessively. If the flashers run for longer than two hours or if
the battery is not fully charged, the battery can be drained.
*
[SC05600(ALL)01/95]
Horn
*
[SC05800(ALL)03/94]
To sound the horn, push the pad in the center of the steering
wheel. Check the horn regularly to be sure it operates properly.
File:cdsco.ex
Update:Thu Jan 25 12:10:03 1996

118
*
[AS02800(ALL)04/95]
n
Using the ªSCAN/TUNEº button to scan radio stations
*
[AS02900(ALL)04/95]
Pressing the ªSCAN/TUNEº button once enters the scan
mode (display will indicate ªSCNº). Pushing the top
ahalf
of the ªSEEKº button will begin the scan mode up the
frequency band, stopping on each listenable station for
approximately five seconds. Pushing the bottom
bhalf of
the ªSEEKº button will begin the scan mode down the
frequency band, again stopping on each listenable station for
approximately five seconds.
*
[AS03000(ALL)04/95]
To stop the scan mode on the presently sampled station
press the ªSCAN/TUNEº button again.
*
[AS03200(ALL)04/95]
n
Setting the Station Memory Preset buttons
*
[AS03300(ALL)02/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS03400(ALL)04/95]1.
Select a band, then select a frequency.
*
[AS03600(ALL)04/95]2.
Press one of the memory buttons and hold the button until
the sound returns. That station is now held in memory on
that button.
*
[AS03700(ALL)04/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS03850(ALL)04/95]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons (if programmed in auto
mode) will need to be reset.
[AS04150(ALL)02/95]
n
Using the Automatic Memory Store feature
*
[AS04250(ALL)05/95]
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your
existing memory presets, which is especially handy while
traveling. Your radio will automatically set your memory
buttons to the strong local stations so you don't have to
continually manually tune to existing stations.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

132
*
[AS22800(ALL)04/95]
n
Using the ªSEEKº function
*
[AS22900(ALL)04/95]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right
aside of the ªSEEKº button to select the next
listenable station up the frequency band. Press the left
b
side of the button to select the next listenable station down
the frequency band. By holding the button down, listenable
stations can be passed over to reach the desired station.
*
[AS23160(ALL)02/95]
n
Using the ªSCANº function (Stereo Cassette Radio)
*
[AS23170(ALL)07/94]
Press the ªSCANº button to enter the scan mode. The radio
will begin scanning up the frequency band, stopping on each
listenable station for approximately a five-second sampling.
This continues until you press the ªSCANº button a second
time. The display flashes ªAMº or ªFM.º
*
[AS23200(ALL)04/95]
n
Setting the Station Memory Preset buttons
*
[AS23325(ALL)02/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS23400(ALL)02/95]
Follow the easy steps below to set these buttons to the desired
frequencies:
*
[AS23525(ALL)04/95]1.
Select a band, then select a frequency.
*
[AS23700(ALL)04/95]2.
Press one of the memory buttons and hold the button until
the sound returns. That station is now held in memory on
that button.
*
[AS23800(ALL)04/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS23900(ALL)04/95]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons (if programmed in auto
mode) will need to be reset.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

163
Roadside Emergencies
*
[RE00310(ALL)03/95]
Jump-Starting Your Vehicle
*
[RE00320(ALL)01/95]
Your vehicle's battery may die if you leave the lights on or any
electrical equipment on after you turn the engine off. If this
happens, you may be able to jump-start from a booster battery
to start your vehicle.
*
[RE00400(ALL)02/95]
RWARNING
The gases around the battery can explode if exposed to
flames, sparks, or lit cigarettes. An explosion could result
in injury or vehicle damage.
*
[RE00500(ALL)02/95]
RWARNING
To protect yourself when charging a battery, always
shield your face and eyes. Make sure that you can
breathe fresh air.
%*
[RE00700(ALL)05/95]
RWARNING
Applying too much pressure on the ends when lifting a
battery could cause acid to spill. Lift the battery with a
carrier or with your hands on the opposite corners.
%*
[RE00800(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE00850(ALL)06/95]
If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15 minutes. If
someone swallows the acid, have him or her drink lots of milk
or water first, then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

164
*
[RE00900(ALL)03/95]
To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your
vehicle to jump-start and connecting the jumper cables in the
order they are given. If in doubt, call for road service.
*
[RE01000(ALL)03/95]
Preparing Your Vehicle
*
[RE01100(ALL)03/95]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[RE01200(ALL)03/95]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[RE01300(ALL)04/95]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01400(ALL)03/95]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE01600(ALL)03/95]5.
Turn on the heater fan in both vehicles. Press the DEFROST
button. Turn off all other switches and gauges.
%*
[RE01700(ALL)05/95]
Connecting the jumper cables
*
[RE02500(ALL)03/95]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[RE02600(ALL)04/95]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

Roadside Emergencies
165
*
[RE02700(ALL)05/95]3.
Connect one end of the second cable to the negative (±)
terminal of the booster battery Ð NOT to the discharged
battery.
*
[RE02800(ALL)04/95]4.
Connect the other end of the second cable to a good metallic
surface on the engine or frame of the disabled vehicle.
*
[RE02900(ALL)05/95]
RWARNING
Do not connect the end of the second cable to the
negative (±) terminal of the battery to be jumped. A
spark may cause an explosion of the gases that surround
the battery.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

Roadside Emergencies
167
*
[RE03400(ALL)03/95]
Jump-Starting
*
[RE03600(ALL)03/95]1.
Make sure that the jumper cables are not in the way of
moving engine parts, then start the booster vehicle. Run the
engine at a moderate speed.
*
[RE03700(ALL)03/95]2.
Let the discharged battery charge for a few minutes and then
start the disabled vehicle. It may take a couple of tries before
the vehicle starts. If the vehicle does not start after several
attempts, there may be a different problem.
*
[RE03800(ALL)03/95]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
*
[RE03900(ALL)03/95]
Removing jumper cables
*
[RE04000(ALL)03/95]1.
Always remove the jumper cables in the reverse order.
Remove the negative (±) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[RE04100(ALL)05/95]2.
Remove the negative (±) cable from the booster battery.
*
[RE04200(ALL)03/95]3.
Remove the positive (+) cable from the booster battery.
*
[RE04300(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
*
[RE04400(ALL)04/95]
After the vehicle is started, let it idle for a while to let the
engine ªrelearnº its idle conditions. Drive it around for a while
with all electrical accessories turned off to let the battery
recharge.You may need to use a battery charger to fully
recharge the battery.
*
[RE04450(ALL)03/95]
If you need to replace your battery, seeBatteryin theServicing
Your Vehiclechapter.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996