1996 FORD CONTOUR engine

Servicing Your Contour
215
[SV18600(ALL)05/95]2.
When the engine is cool, wrap a thick cloth around the cap
and turn it slowly counterclockwise to relieve the pressure.
*
[SV18700(ALL)03/95]3.
Step back while the pressure releases.
[SV18800(ALL)05/95]4.
When you are sure that all the pressure has been released,
use the cloth to turn and remove cap.
*
[SV18900(ALL)02/95]5.
Stand away from the reservoir opening. Hot steam may blow
out or hot engine coolant may even splash out.
*
[SV19000(ALL)01/95]
RWARNING
Failure to follow these instructions could result in serious
personal injury from hot engine coolant or steam
blowout and/or damage to the engine cooling system or
engine.
*
[SV19025(ALL)03/95]
To find out how much engine coolant mixture your vehicle's
coolant system can hold, seeRefill capacities for fluidsin the
Index.
*
[SV19100(ALL)01/95]
Have your dealer check the engine cooling system for leaks if
you have to add a quart (liter) of engine coolant more than
once a month.
*
[SV19102(ALL)06/95]
Add engine coolant only to the recovery reservoir.If the
coolant level is low, add to the reservoir a 50/50 mixture of
water and the type of engine coolant that Ford specifies. You
may add water by itself only in an emergency, but you should
replace it with a 50/50 mixture as soon as possible. Check the
engine coolant again the next few times you drive your vehicle.
*
[SV19104(ALL)02/95]
Ford Premium Cooling System Fluid is an optimized formula
that will protect all metals and rubber elastomers used in Ford
engines for four years or 50,000 miles (80,000 km). It is not
necessary and not recommended to use supplemental coolant
additives in your vehicle. These additives may harm your
engine cooling system. Follow the recommended service interval
for changing your engine coolant.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

216
*
[SV19106(ALL)04/94]
NOTE: When you change or add engine coolant, it is
important to maintain your engine coolant
concentration between 40%(-11ÊF [-24ÊC]) and 60%
(-62ÊF [-52ÊC]),depending on your local climate
conditions. Below 40% you will lose freeze protection
and above 60% your engine may overheat on a warm
day.
*
[SV19108(ALL)03/95]
NOTE: The use of an improper coolant may void your
warranty for the engine cooling system. Use only a
premium, nationally recognized brand name engine
coolant. Do not use alcohol, methanol antifreeze or
engine coolant mixed with alcohol or methanol
antifreeze. If you do not use the proper coolant, the
aluminum engine on your vehicle will corrode.
*
[SV19110(ALL)05/95]
Ford Motor Company expressly authorizes the Ford Rotunda
engine coolant recycling process and chemicals. Use only Ford
Rotunda recycled engine coolant or an equivalent recycled
engine coolant that is certified by the supplier to meet Ford
specification ESE-M97B44-A.
%*
[SV19112(ALL)04/95]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
[SV19115(ALL)02/95]
Use Ford Premium Cooling System Fluid or an equivalent
engine coolant that meets Ford Specification ESE-M97B44-A.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

Servicing Your Contour
219
[SV20660(ALL)06/95]
Disconnecting the Battery
[SV20675(ALL)02/95]
Because your vehicle engine is electronically controlled by a
computer, some control conditions are maintained by power
from the battery. If you ever disconnect the battery or install a
new battery, you must allow the computer to ªrelearnº its idle
conditions before your vehicle will drive properly. To begin this
process, put the gearshift in P (Park) (automatic transaxle) or
Neutral (manual transaxle), set the emergency brake, turn off all
the accessories, and start the vehicle. Bring the engine to normal
operating temperature. Allow the manual transaxle to idle for
one minute in Neutral. Allow the automatic transaxle engine to
idle for one minute in N (Neutral) and one minute in D (Drive).
Perform the previous procedure with the air conditioning (if
equipped) on and off (conditions permitting). The relearning
process will complete automatically as you drive the vehicle.
*
[SV20700(ALL)03/95]
If you do not let the engine relearn its idle, the idle quality of
your vehicle may be adversely affected until the idle is
relearned. Your vehicle will eventually relearn its idle while you
drive it, but it takes much longer than if you use the previous
procedure.
*
[SV21700(ALL)03/95]
Windshield Washer Fluid and Wipers
*
[SV21800(ALL)03/95]
Washer Fluid
*
[SV22100(ALL)01/95]
Check the level of the windshield washer fluid every time you
stop for fuel. The reservoir for washer fluid is located on the
passenger's side of the engine compartment. Visual inspection
can determine if the washer fluid is adequate. Do not operate
the washer when the reservoir is empty.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

220
[SV22200(ALL)02/94]
10-1/2 pica
art:0001222-A
The windshield washer fluid reservoir
*
[SV22300(ALL)03/95]
Adding washer fluid
*
[SV22400(ALL)05/95]
RWARNING
Do not put windshield washer fluid in the container for
the engine coolant.
[SV22450(ALL)05/95]
If sprayed to clean the glass, engine coolant or antifreeze could
make it difficult to see through the windshield.
%*
[SV22500(ALL)01/95]
Use specially formulated windshield washer fluid rather than
plain water, because specially formulated washer fluids contain
additives that dissolve road grime. For safety reasons, washer
fluids containing an appropriate antifreeze such as methanol
should be used in freezing weather (temperatures below32ÊF
[0ÊC]). State or local regulations on Volatile Organic Compounds
(VOC's) may restrict use of the most common antifreeze,
methanol. Washer fluids containing non-methanol antifreeze
agents should be used only if they provide cold weather
protection without damaging the vehicle's paint finish, wiper
blades, and windshield washer system.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

222
[SV23730(ALL)07/94]
7-1/2 pica art:0001242-A
The screws on the grille
[SV23736(ALL)02/95]2.
Remove the plastic caps from the screws on the grille.
Remove the screws.
[SV23741(ALL)02/95]3.
Open the hood. Pull off the rubber weatherstrip at the back
of the engine compartment. Remove the screws that hold the
grille, separate the two halves and remove the grille.
[SV23746(ALL)11/93]
13-1/2 pica
art:0001243-A
Removing the grille
[SV23751(ALL)07/94]4.
The filter is in a housing at the back of the engine
compartment, on the left side. Pull off the two clips on the
sides of the housing. Slide out the housing and filter.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

Servicing Your Contour
229
*
[SV29151(ALL)05/94]
n
Remove tire chains at the first opportunity after using them
on snow and ice. Do not use the chains on dry roads.
%*
[SV29200(ALL)04/95]
Cleaning the Wheels
*
[SV29225(ALL)05/95]
Wash the wheels with the same detergent you use to wash your
vehicle's body. Do not use acid-based wheel cleaners, steel wool,
abrasives, fuel, or strong detergents. These substances will
damage protective coatings. Use tar and road oil remover to
remove grease and tar.
*
[SV29250(ALL)04/95]
NOTE: Before going to a car wash, find out if the brushes are
abrasive.
*
[SV29300(ALL)03/01]
Automatic Transaxle Fluid
*
[SV29310(ALL)03/95]
Under normal circumstances, you do not need to check the fluid
level of the transaxle, since your vehicle does not use up
transaxle fluid. Refer to theMaintenance Schedule and Record
booklet for replacement intervals. However, if the transaxle is
not working properly Ð for instance, the transaxle may slip or
shift slowly, or you may notice some sign of fluid leakage Ð
the fluid level should be checked.
%*
[SV29340(ALL)02/93]
Checking the Automatic Transaxle Fluid
*
[SV29350(ALL)01/95]
With the vehicle on a level surface and the brake fully applied,
start the engine and move the gear shift selector through all of
the gears allowing sufficient time for each position to engage.
Securely latch the gear shift selector in the P (Park) position.
Fully set the parking brake and leave the engine running.
*
[SV29370(ALL)01/95]
Wipe off the dipstick cap and pull the dipstick out. Wipe the
indicator end clean. Put the dipstick back into the filler tube and
make sure it is fully seated. Pull the dipstick out and read the
fluid level.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

232
*
[SV30200(ALL)03/95]
Brake Fluid
*
[SV30300(ALL)04/95]
Under normal circumstances, your vehicle should not use up
brake fluid rapidly. However, expect the level of the brake fluid
to slowly fall as you put more mileage on your vehicle and the
brake lining wears.
[SV30401(ALL)02/94]
You should check the brake fluid at every scheduled engine oil
change, but be sure to check it at least once a year. You can do
this by looking at the fluid level in the plastic reservoir on the
master cylinder. (SeeThe Engine Typesin this chapter to locate
the brake fluid reservoir.) The fluid level should be at or near
the MAX mark.
*
[SV30450(ALL)05/95]
RWARNING
Brake fluid is toxic.
*
[SV30475(ALL)06/95]
If brake fluid contacts eyes, flush eyes with running water for
15 minutes. Get medical attention if irritation persists. If taken
internally, drink water and induce vomiting. Get medical
attention immediately.
*
[SV30500(ALL)03/95]
If the fluid is low, carefully clean and remove the cap from the
reservoir. Fill the reservoir to the MAX line with Ford High
Performance DOT 3 Brake Fluid C6AZ-19542-AA or equivalent
DOT 3 fluid meeting Ford specification ESA-M6C25-A.
*
[SV30800(ALL)01/95]
RWARNING
If you use a brake fluid that is not DOT 3, you will
cause permanent damage to your brakes.
*
[SV30900(ALL)01/95]
Do not fill the reservoir above the MAX line.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

234
*
[SV31200(ALL)03/95]
Power Steering Fluid
*
[SV31225(ALL)03/95]
Checking and Adding Power Steering Fluid
[SV31250(ALL)05/94]
With the power steering system at operating temperature,
switch off the engine. The fluid level should be up to the MAX
marking on the transparent reservoir.
[SV31275(ALL)05/94]
If it drops to or below the MIN mark, top off with the specified
fluid.
[SV31350(ALL)05/94]
10-1/2 pica
art:0001260-A
The power steering fluid reservoir
[SV32000(ALL)05/95]
Use only power steering fluid that meets Ford's Specification
ESW-M2C33-F or is an equivalent Type F Automatic
Transmission Fluid with a Ford registration number (an 8-digit
number beginning with ª2Pº printed on the fluid container).
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996