1996 FORD CONTOUR wheel

83
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side of the steering
column to:
*
[SC00700(ALL)03/95]
n
operate the turn signals and cornering lamps
*
[SC00800(ALL)01/95]
n
turn the high beams on/off
*
[SC00900(ALL)05/95]
n
flash the lamps
*
[SC01100(ALL)01/95]
Turn Signals
[SC01200(ALL)01/95]
10-1/2 pica
art:0001186-D
The turn signal lever
*
[SC01300(ALL)03/95]
Move the lever up to signal a right turn. Move it down to
signal a left turn. The corresponding indicator light in the
instrument cluster will flash.
*
[SC01400(ALL)03/95]
If the turn signal stays on after you turn, move the lever back
to the center (off) position.
*
[SC01500(ALL)03/95]
For lane changes, move the lever far enough to signal but not to
latch. The lever will return to the off position when you release
it.
File:cdsco.ex
Update:Thu Jan 25 12:10:03 1996

86
%*
[SC05520(ALL)03/95]
Hazard Flasher
*
[SC05530(ALL)03/95]
The hazard flasher serves as a warning to other drivers to be
careful when approaching or passing your vehicle.
[SC05540(ALL)05/94]
10-1/2 pica
art:0001193-A
Using the hazard flasher switch
*
[SC05590(ALL)03/95]
The flashers work whether your vehicle is running or not. The
flashers work for up to two hours when the battery is fully
charged and in good condition without draining the battery
excessively. If the flashers run for longer than two hours or if
the battery is not fully charged, the battery can be drained.
*
[SC05600(ALL)01/95]
Horn
*
[SC05800(ALL)03/94]
To sound the horn, push the pad in the center of the steering
wheel. Check the horn regularly to be sure it operates properly.
File:cdsco.ex
Update:Thu Jan 25 12:10:03 1996

88
[SC07700(ALL)05/94]
10-1/2 pica
art:0000262-D
The speed control switches on the steering wheel
[SC08200(ALL)04/95]
Setting the speed control
*
[SC08400(ALL)06/95]1.
Press and release the ON switch.
*
[SC08500(ALL)06/95]2.
Accelerate to the desired speed above 30 mph (50 km/h)
using the accelerator pedal.
[SC08800(ALL)05/95]3.
Press the SET ACC switch and release it immediately to set
your speed. If you keep this switch depressed, your speed
will continue to increase.
[SC08900(ALL)05/95]4.
Take your foot off the accelerator pedal. Your vehicle will
maintain the speed you set.
File:cdsco.ex
Update:Thu Jan 25 12:10:03 1996

Features
103
*
[FV11600(ALL)05/95]
RWARNING
To reduce the risk of serious injury in a collision, always
drive and ride with your seatback upright and the lap
belt snug and low across the hips.
*
[FV11700(ALL)05/95]
RWARNING
Do not pile cargo higher than the seatbacks to avoid
injuring people in a collision or sudden stop.
[FV11801(ALL)02/94]
Manual lumbar support (If equipped)
[FV11901(ALL)02/94]
The handwheel on the side of the seatback inflates and deflates
the lumbar support pads. To inflate the pads, turn the wheel
counter-clockwise. To deflate the pads, turn the wheel clockwise.
[FV12001(ALL)02/94]
10-1/2 pica
art:0001261-A
Manual lumbar support adjustment
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

Features
107
*
[FV14000(ALL)01/95]
Mirrors
*
[FV14600(ALL)01/93]
Side View Mirrors
[FV14700(ALL)04/94]
The standard side view mirrors are manually adjusted by using
the remote knobs. The knob on each door adjusts the mirror on
that side of the vehicle. Move the control knob in the direction
you want to move the mirror.
[FV14800(ALL)02/94]
10-1/2 pica
art:0000463-B
The left side mirror control (right side similar)
[FV14850(ALL)05/94]
Dual electric remote control mirrors (if equipped)
[FV14900(ALL)05/94]
The control for adjusting the electric side view mirrors is on the
instrument panel, to the left of the steering wheel.
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

139
Driving Your Contour
*
[DR00200(ALL)09/93]
Procedures for driving your vehicle will vary depending on
which type oftransaxleyour vehicle has. You may be familiar
with the term ªtransmission.º We usetransaxlebecause it is a
more accurate term for vehicles that have front-wheel drive.
*
[DR00300(ALL)11/94]
Your vehicle will have one of the following types of transaxles:
[DR00410(ALL)02/94]
n
an automatic overdrive transaxle with transaxle control
switch, or
*
[DR00600(ALL)11/94]
n
a manual transaxle.
*
[DR00700(ALL)11/94]
If you are not sure which transaxle your vehicle has, talk to
your dealer.
*
[DR00750(ALL)04/95]
Your vehicle is equipped with an Electronic Powertrain Control
Module that limits engine and/or vehicle speeds with a cut-out
mode to promote durability.
*
[DR00800(ALL)01/95]
Driving with an Automatic Overdrive
Transaxle
[DR00850(ALL)05/95]
Your automatic overdrive transaxle provides fully automatic
operation in either D (Overdrive) or with the transaxle control
switch depressed. Driving with the shift selector in D
(Overdrive) gives the best fuel economy for normal driving
conditions. For manual control, start in 1 (First) and then shift
manually.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

142
[DR01100(ALL)05/94]
13-1/2 pica
art:0000492-D
Console-mounted automatic transaxle shift control lever
%*
[DR01600(ALL)01/95]
R (Reverse)
*
[DR01700(ALL)02/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR01725(ALL)01/95]
N (Neutral)
[DR01750(ALL)11/94]
In N (Neutral), the wheels of the transaxle are not locked. Your
vehicle will roll freely, even on the slightest incline, unless the
parking brake or brakes are on.
*
[DR01800(ALL)01/95]
Driving
[DR01825(ALL)02/94]
Your vehicle's gearshift is console-mounted on the floor. The
Transaxle Control Switch (TCS) is located on the gearshift
handle. The transaxle control indicator light (OD OFF) is located
on the instrument panel. You can put the gearshift lever in any
of the several positions.
[DR01850(ALL)05/94]
The OD OFF light is off (not illuminated) during normal vehicle
operation. This allows the transaxle to upshift and downshift
from first through fourth gears. When the TCS is pressed, the
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

144
*
[DR02100(ALL)01/95]
When to use 2 (Second)
[DR02200(ALL)05/94]
When your vehicle is in 2 (Second), it automatically starts off in
second gear. Use 2 (Second) to help drive up moderately steep
hills or restart from a standstill on slippery roads. It prevents
the transaxle from frequently shifting up and down. It also
gives more engine braking than D (Drive) (with Transaxle
Control Switch activated) when going down hills.
[DR02300(ALL)05/95]
Do not go faster than 55 mph (90 km/h) in this gear. You can
upshift from 2 (Second) into D (Overdrive) at any speed.
*
[DR02500(ALL)04/95]
When to use 1 (First)
[DR02700(ALL)05/94]
This position limits the transaxle to first gear. It helps brake the
vehicle when going down hills where 2 (Second) is not
sufficient.
[DR02800(ALL)05/95]
Do not go faster than 38 mph (60 km/h) in this gear. You can
upshift from 1 (First) to 2 (Second) or from 1 (First) to
D (Overdrive) at any speed.
*
[DR02900(ALL)01/95]
P (Park)
*
[DR03000(ALL)11/94]
Always come to a complete stop before you shift into P (Park).
Make sure that the gearshift is securely latched in P (Park). This
locks the transaxle and prevents the front wheels from rotating.
*
[DR03100(ALL)05/95]
RWARNING
Always set the parking brake fully and make sure that
the gearshift is securely latched in P (Park).
*
[DR03200(ALL)06/95]
RWARNING
Never leave your vehicle unattended while it is running.
[DR03400(ALL)01/89]
You can tell the gearshift is securely latched when the push
button has popped out. In this position the gear shift selector
lever cannot be moved unless the button is pushed in.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996