1996 FORD CONTOUR reset

Electronic Sound Systems
119
*
[AS04350(ALL)02/95]
Activate Auto Memory Store by pushing the ªAUTO
PRESETº button once. Your radio will set the first five
strong stations of the band you are in (AM, FM1 or FM2)
into the memory buttons. The display will show ªAUTOº,
then run through the frequencies, stopping momentarily on
the stations being set into the memory buttons. The radio is
now in the ªAUTOº mode and this display will show
ªAUTOº each time a preset is activated.
*
[AS04450(ALL)05/95]
NOTE: If there are fewer than five strong stations in the
frequency band, the remaining unfilled buttons will
store the last strong station detected on the band.
*
[AS04550(ALL)05/95]
After all stations have been filled, the radio will begin
playing the station stored on memory button 1.
*
[AS04560(ALL)04/95]
To deactivate the Auto Memory Store mode and return to
the manually-set memory button stations (or those stations
set using Auto Memory Load), simply push the ªAUTO
PRESETº button. Display will show ªAUTOº then ªOFFº.
The next time Auto Memory Store is activated on that band,
the radio will store the next set of five strong stations.
*
[AS04600(ALL)02/95]
Adjusting the tone balance and speaker output of your
radio
*
[AS04700(ALL)04/95]
n
Increasing or decreasing bass response
[AS04750(ALL)07/94]
Push the ªAUDIOº button repeatedly until the display reads
ªBASSº. Push the top (+) of the ªVOLUMEº button to
increase bass (more ªlowsº), and push the button (s)to
decrease bass (less ªlowsº).
*
[AS04800(ALL)04/95]
n
Increasing or decreasing treble response
[AS04900(ALL)07/94]
Push the ªAUDIOº button repeatedly until the display reads
ªTREBº. Push the top (+) of the ªVOLUMEº button to
increase treble (more ªhighsº), and push the bottom (s)to
decrease treble (less ªhighsº).
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

132
*
[AS22800(ALL)04/95]
n
Using the ªSEEKº function
*
[AS22900(ALL)04/95]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right
aside of the ªSEEKº button to select the next
listenable station up the frequency band. Press the left
b
side of the button to select the next listenable station down
the frequency band. By holding the button down, listenable
stations can be passed over to reach the desired station.
*
[AS23160(ALL)02/95]
n
Using the ªSCANº function (Stereo Cassette Radio)
*
[AS23170(ALL)07/94]
Press the ªSCANº button to enter the scan mode. The radio
will begin scanning up the frequency band, stopping on each
listenable station for approximately a five-second sampling.
This continues until you press the ªSCANº button a second
time. The display flashes ªAMº or ªFM.º
*
[AS23200(ALL)04/95]
n
Setting the Station Memory Preset buttons
*
[AS23325(ALL)02/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS23400(ALL)02/95]
Follow the easy steps below to set these buttons to the desired
frequencies:
*
[AS23525(ALL)04/95]1.
Select a band, then select a frequency.
*
[AS23700(ALL)04/95]2.
Press one of the memory buttons and hold the button until
the sound returns. That station is now held in memory on
that button.
*
[AS23800(ALL)04/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS23900(ALL)04/95]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons (if programmed in auto
mode) will need to be reset.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

Roadside Emergencies
175
*
[RE14800(ALL)03/95]
Replacing the anti-theft lug nut
*
[RE14900(ALL)03/95]
Insert the key over the locking lug nut. Place the lug nut
wrench over the lug nut key and, while applying pressure on
the key, install the lug nut.
*
[RE15050(ALL)02/95]
If the Engine Cranks But Does Not Start or
Does Not Start After a Collision
*
[RE15100(ALL)04/95]
The Fuel Pump Shut-off Switch
*
[RE15200(ALL)03/95]
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device that stops the fuel
pump when your vehicle has been involved in a substantial jolt.
*
[RE15250(ALL)01/95]
For information on how to check and reset the fuel pump
shut-off switch, seeFuel pump shut-off switchin the Index.
*
[RE16400(ALL)05/95]
Towing Your Vehicle
*
[RE16500(ALL)04/95]
If you need to have your vehicle towed, contact a professional
towing service or, if you are a member, your roadside assistance
center. Recommended towing options include wheel lift towing
or flat bed towing.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

Servicing Your Contour
243
[SV36000(ALL)05/94]
7-1/2 pica art:0001319-A
The side view of a typical fuse
[SV36200(ALL)04/94]
eight pica
chart:0001255-B*
[SV36300(ALL)05/95]
RWARNING
Always replace a fuse with one that has the specified
amperage rating. Using a fuse with a higher amperage
rating can cause severe wire damage and could start a
fire.
%*
[SV36700(ALL)03/95]
Circuit Breakers
[SV36900(ALL)02/94]
If you need to check a circuit breaker that is on the instrument
panel fuse panel, seeChecking and replacing fusesto find out how
to locate the fuse panel and pull it down.
*
[SV37000(ALL)02/95]
Diagnostic equipment is needed to check circuit breakers. Refer
to the manufacturer's instructions.
[SV37100(ALL)02/95]
Circuit breakers will reset themselves and allow the electrical
parts to work again once the overload on the circuit is gone. If
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

250
%*
[SV42425(ALL)06/95]
Readiness for Inspection/Maintenance Testing
*
[SV42450(ALL)06/95]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If the vehicle's powertrain system or its battery
has just been serviced, the OBD II system is reset to a not ready
for I/M testing condition. To prepare for I/M testing, the law
specifies a ªneed for additional mixed city and highway driving
to complete the checkº of the OBD II system. As soon as all of
the OBD II system checks are successfully completed, the OBD
II system is set to the ready condition. The amount of driving
required to reach the ready condition varies with individual
driving patterns. To complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle defined below.
If the vehicle owner cannot or does not want to do the
additional driving required by law, a service center can perform
this drive cycle as it would any other type of repair work.
*
[SV42475(ALL)06/95]
OBD II Drive Cycle
*
[SV42501(ALL)06/95]
The following steps must be run in the order shown. If any
steps are interrupted, repeat the preceding step. Any safe
driving mode is acceptable between steps.
*
[SV42550(ALL)06/95]
Always drive vehicle in safe manner according to traffic
conditions and obey all traffic laws.
*
[SV42560(ALL)05/95]
The engine must be warmed up and at operating temperature
before proceeding with the drive modes of the following OBD II
Drive Cycle.
*
[SV42575(ALL)05/95]1.
Start the engine. Drive or idle (in neutral) the vehicle for
4 minutes.
[SV42601(ALL)05/95]2.
Idle the vehicle in Drive (Neutral for manual transaxle) for
40 seconds.
*
[SV42610(ALL)06/95]3.
Accelerate the vehicle to 45 mph (70 km/h) at 1/4 to 1/2
throttle for 10 seconds.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

287
Servicing your vehicle
precautions when servicing.............. 196
servicing when you tow............... 161
Shift-lock system................... 140
Shift positions (see Gearshift)............140, 145
Shoulder and lap belts (see Safety restraints)........ 9
Side mirrors, adjusting................. 107
Sliding moon roof (see Moon roof)............ 99
Snow tires and chains................. 228
Spare tire
changing the tire.................. 168
finding the spare.................. 169
removing the spare tire............... 169
temporary spare................... 168
Spark plugs, specifications............... 253
Special driving conditions............... 153
Specification chart, lubricants.............. 254
Speed control
accelerating...................... 90
canceling a set speed................. 91
resetting....................... 90
resuming a set speed................. 91
tap up/tap down................... 90
turning off...................... 91
when towing a trailer................ 161
Speedometer...................... 65
Starting your vehicle
preparing to start your vehicle............. 44
starting a cold engine................. 46
starting after a collision................ 50
starting a warm engine................ 47
starting your vehicle if the battery is disabled..... 163
Steering, power.................... 149
Steering wheel
horn......................... 86
locking........................ 41
speed controls.................... 88
File:cdixo.ex
Update:Thu Jan 25 12:10:47 1996