1996 FORD ASPIRE lock

33 [SR17275(ALL)07/95]
half page art:0032271-A
Setting the retractor to automatic locking mode
*
[SR17280(ALL)07/95]
5. Allow the belt to retract. Pull up on the
shoulder webbing. A clicking sound will be
heard as the belt retracts. This indicates the
retractor is in the automatic locking mode.
Push down on the child seat while you pull
up on the belt to remove any slack in the
belt. See Figures 5 and 6.
File:03icsrf.ex
Update:Wed Jan 24 14:30:01 1996

35 [SR17284(ALL)07/95]
half page art:0032246-C
Removing slack from the belt
*
[SR17286(ALL)07/95]
6. Before placing the child in the child seat,
forcibly tilt the seat from side to side, and
tug it forward to make sure that the seat is
securely held in place. See Figure 7.
[SR17300(ALL)05/95]
7. Double-check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode. See
Figure 8.
File:03icsrf.ex
Update:Wed Jan 24 14:30:01 1996

36 [SR17310(ALL)07/95]
half page art:0032275-AChecking that retractor is in automatic locking mode
[SR17325(ALL)05/95]
8. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
[SR17350(ALL)05/95]
NOTE: To remove the retractor from the
automatic lock mode, allow the seat belt to
retract fully to its stowed position and the
retractor will automatically switch back to the
vehicle sensitive locking mode for normal adult
usage.
File:03icsrf.ex
Update:Wed Jan 24 14:30:01 1996

37
*
[SR20200(ALL)06/95]
Attaching Safety Seats With Tether Straps
*
[SR20300(ALL)06/95]
Some manufacturers make safety seats that
include a tether strap that goes over the back of
the vehicle seat and attaches to an anchoring
point. Other manufacturers offer the tether strap
as an accessory. Contact the manufacturer of
your child safety seat for information about
ordering a tether strap.
*
[SR20350(ALL)07/95]
Front Seats
*
[SR20400(ALL)07/95]
To install a tether from a child safety seat in the
front seat:
[SR20425(ALL)07/95]
1. Buckle the lap/shoulder belt in the right rear
seat.
*
[SR20450(ALL)07/95]
2. Pull all the stored belt out of the rear seat
retractor to switch the retractor to automatic
locking mode.
*
[SR20500(ALL)07/95]
3. Let the retractor wind up the slack from the
lap/shoulder belt.
*
[SR20525(ALL)07/95]
4. Install the child safety seat in the front seat.
Refer to the previous section onInstalling
Safety Seats. Hook the tether strap hook
around the webbing near the center of the
shoulder portion of the locked lap/shoulder
belt.
*
[SR20550(ALL)07/95]
5. Tighten the tether strap.
*
[SR20575(ALL)07/95]
Rear Seats
*
[SR20600(ALL)07/95]
If you use a tethered safety seat on one of the
rear seats, you can anchor the strap to the
appropriate tether anchor directly behind that
seat position.
File:03icsrf.ex
Update:Wed Jan 24 14:30:01 1996

41
Starting Your Aspire
*
[ST01700(ALL)03/95]
Ignition
*
[ST01800(ALL)01/95]
Understanding the Positions of the Ignition
[ST01900(ALL)01/95]
The ignition has four positions. They are: LOCK,
ACC, ON, and START.
[ST02000(ALL)05/93]
one third page art:0032158-A
Ignition lock cylinder (manual transaxle)
[ST02050(ALL)05/93]
one third page art:0032159-A
Ignition lock cylinder (automatic transaxle)
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

42
*
[ST02100(ALL)09/93]
LOCK locks the steering wheel. It also locks the
gearshift lever in P (Park) (automatic transaxle).
*
[ST02200(ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[ST02300(ALL)05/95]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
[ST02325(ALL)09/93]
If your vehicle has a manual transaxle, you must
push the key toward the steering column to
rotate the switch to the LOCK position.
%*
[ST02350(ALL)03/95]
ACC (accessory) allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[ST02400(ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST02500(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

43
*
[ST02505(ALL)09/93]
Shift-lock System
*
[ST02510(ALL)07/95]
For your safety, the optional automatic transaxle
has a shift-lock system, which prevents shifting
the transaxle out of the P (Park) position without
depressing the brake pedal when the ignition
key is in the ON position.
*
[ST02515(ALL)07/89]
To shift the transaxle out of the P (Park)
position:
*
[ST02521(ALL)05/90]
1. Depress and hold the brake pedal.
*
[ST02526(ALL)11/93]
2. Start the engine.
[ST02528(ALL)02/92]
3. Push in the thumb lock button and move the
gearshift lever.
[ST02529(ALL)07/93]
4. SeeEmergency Override Systemlater in this
section for more information.
*
[ST02535(ALL)09/93]
NOTE: When the ignition key is in the ACC
or LOCK position, the transaxle cannot
be shifted from the P (Park) position.
If the brake pedal is repeatedly
depressed and released when the
ignition is in the ON position and the
selector lever is in the P (Park)
position, a chattering near the gearshift
lever may be heard. This is not a
malfunction.
*
[ST02538(ALL)03/94]
NOTE: Your vehicle's gearshift lever is
securely latched in P (Park) if you
cannot move it without pushing in the
thumb button. Keep the brake pedal
depressed while moving your gearshift
lever.
*
[ST02540(ALL)09/93]
To make the system more effective, the ignition
key cannot be removed unless the gearshift
selector lever is in the P (Park) position.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

44 [ST02650(ALL)07/93]Emergency Override System
[ST02720(ALL)09/93]
Your vehicle has a cap covering the override
mechanism for the shift-lock feature. If you have
to use the override procedure to move the
gearshift lever out of the P (Park) position,
follow these instructions:
*
[ST02740(ALL)06/95]
1. Remove the shift-lock override cap with a 1ª
or longer screwdriver.
*
[ST02760(ALL)03/93]
2. Insert the screwdriver into the shift-lock
override opening and push the screwdriver
handle down.
[ST02780(ALL)12/93]
two third page art:0032202-C
Operating the shift-lock override mechanism
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996