1996 FORD ASPIRE clock

181 [SV07590(ALL)05/95]
RWARNING
Do not overfill the fuel tank. The pressure
in an overfilled tank may cause leakage
and lead to fuel spray and fire.
*
[SV07595(ALL)05/95]
Before you fill your vehicle with fuel, extinguish
all lit cigarettes, other smoking materials, and
any open flames.
*
[SV07600(ALL)05/95]
To fill the tank properly:
*
[SV07610(ALL)05/95]
1. Remove the fuel cap. Proceed to add fuel to
the tank only if your vehicle is on level
ground.
[SV07620(ALL)05/95]
2. Make sure that you pump unleaded fuel and
put the nozzle all the way inside the fuel
filler pipe. The fuel tank is normally full
after three automatic shutoffs of the nozzle.
[SV07630(ALL)05/95]
3. If you spill any fuel on the body of your
vehicle, clean it off immediately. The fuel
may dull or soften the paint if you do not
wash it off.
[SV07640(ALL)05/95]
4. Replace the fuel cap tightly when you are
finished. Turn it clockwise until you hear at
least three clicks.
*
[SV07650(ALL)05/95]
5. Push the fuel door closed.
*
[SV07670(ALL)06/95]
Choosing the Right Fuel
*
[SV07680(ALL)06/95]
Use only UNLEADED FUEL in your vehicle.
Using leaded fuel is prohibited by federal law.
Your warranty may not apply if your vehicle is
damaged because you used the wrong fuel.
*
[SV07690(ALL)06/95]
Vehicle inspection programs may detect
misfueling. Under these circumstances, you may
be required by law to make costly repairs at
your own expense.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

192
*
[SV18800(ALL)06/95]
RWARNING
Follow these steps to minimize risk of
personal injury.
*
[SV18900(ALL)07/95]
1. Before you remove the radiator cap, turn the
engine off and let it cool. Even when the
engine is cool, be careful when you remove
the radiator cap.
*
[SV19000(ALL)05/95]
2. When the engine is cool, wrap a thick cloth
around the cap and turn it slowly
counterclockwise to the first stop.
*
[SV20000(ALL)03/95]
3. Step back while the pressure releases.
*
[SV20100(ALL)03/95]
4. When you are sure that all the pressure has
been released, use the cloth to turn and
remove cap.
*
[SV20200(ALL)03/95]
5. Stand away from the radiator opening. Hot
steam may blow out or hot engine coolant
may even splash out.
*
[SV20250(ALL)01/95]
RWARNING
Failure to follow these instructions could
result in serious personal injury from hot
engine coolant or steam blowout and/or
damage to the engine cooling system or
engine.
*
[SV20300(ALL)03/95]
To find out how much engine coolant mixture
your vehicle's coolant system can hold, seeRefill
capacities for fluidsin the Index.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

227
*
[SV41500(ALL)03/95]
Installing the headlamp bulb
[SV41600(ALL)07/93]
1. Insert the glass end of the bulb assembly
into the socket.
[SV41650(ALL)05/93]
2. Secure the bulb assembly in place with the
metal retaining clip.
[SV41675(ALL)05/93]
3. Attach the rubber boot over the bulb
assembly.
[SV41700(ALL)05/93]
4. Slip the bulb retaining ring over the boot
and bulb assembly. Lock the ring into the
socket by rotating it clockwise until you feel
a ªstopº.
[SV41800(ALL)05/93]
5. Push the electrical connector into the rear of
the bulb assembly until it locks into position.
[SV41900(ALL)02/95]
6. Turn the headlamps on and make sure they
work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
*
[SV42000(ALL)02/95]
High-Mount Brakelamp Bulbs
[SV42100(ALL)02/95]
To replace the high-mount brakelamp bulb, refer
to the instructions below or take your vehicle to
your Ford dealer or a qualified technician.
[SV42200(ALL)05/94]
To remove the high-mount brakelamp:
[SV42300(ALL)05/93]
1. Disconnect the negative battery cable.
[SV42400(ALL)05/94]
2. Raise the hatchback.
[SV42450(ALL)05/94]
3. Use a Phillips screwdriver to remove three
attaching screws from the rear wiper motor
cover (if equipped). Lay the cover aside.
[SV42600(ALL)05/94]
4. Gently pull the hatchback trim panel away
from the hatchback.
[SV42700(ALL)05/94]
5. Disconnect the luggage compartment lamp
electrical connector (if equipped) and lay the
trim panel aside.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

228 [SV42800(ALL)05/94]6. Rotate the high-mount lamp socket
counterclockwise and remove it from the
housing.
[SV42900(ALL)05/94]
7. Carefully remove the bulb by gently pulling
it straight from the socket.
*
[SV43000(ALL)03/95]
To install a bulb:
[SV43100(ALL)05/94]
1. Firmly install the replacement bulb into the
socket.
[SV43200(ALL)05/94]
2. Place the socket assembly in the high-mount
stoplamp housing and turn clockwise to lock
into position.
[SV43300(ALL)05/94]
3. Position the hatchback trim panel and
connect the luggage compartment lamp
electrical connector (if equipped).
[SV43400(ALL)05/94]
4. Insert the trim panel retaining clips into the
locating holes in the hatchback and push
each clip firmly into position.
[SV43500(ALL)05/94]
5. Install the rear wiper motor cover (if
equipped).
[SV43600(ALL)05/94]
6. Close the hatchback and reconnect the
negative battery cable.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996