1996 FORD AEROSTAR engine

286 [SV17950(ALL)08/95]Adding Engine Coolant
[SV18000(ALL)08/95]
quarter page art:0020354-A
Adding engine coolant to reservoir
[SV20075()08/95]
RWARNING
Be careful not to add engine coolant to
the windshield washer fluid reservoir. If
sprayed on the windshield, engine coolant
could make it difficult to see through the
windshield.
[SV20100()08/95]
When the engine is cool, add a 50/50 mixture of
engine coolant and water to the engine coolant
recovery reservoir - DO NOT ADD DIRECTLY
TO THE RADIATOR. Add straight water only in
an emergency, but you should replace it with a
50/50 mixture of coolant and distilled water as
soon as possible.
[SV20125()08/95]
Check the coolant level in the coolant recovery
reservoir the next few times you drive the
vehicle. If necessary, add enough of a 50/50
mixture of coolant and water to bring the liquid
level to the fill line on the reservoir.
[SV20150()08/95]
RWARNING
Never remove the coolant recovery cap
while the engine is running or hot.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

287 [SV20175()08/95]
If you must remove the coolant recovery cap,
follow these steps to avoid personal injury
casued by escaping steam or engine coolant:
[SV20200()08/95]
1. Before you remove the cap, turn the engine
off and let it cool.
[SV20225()08/95]
2. When the engine is cool, wrap a thick cloth
around the cap and turn it slowly,
counterclockwise to the first stop.
[SV20250()08/95]
3. Step back while the pressure releases.
[SV20275()08/95]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it counterclockwise, and remove
it.
[SV20295()08/95]
UseFord Premium Engine Coolant
E2FZ-19549-AA(in Canada, Motorcraft CXC-8-B)
or an equivalent premium engine coolant that
meets Ford Specification ESE-M97B44-A. Ford
Premium Engine Coolant is an optimized
formula that will protect all metals and rubber
elastomers used in Ford cooling systems for 4
years or 50,000 miles (80,000 km).
[SV20300()08/95]
Do not use alcohol or methanol antifreeze or any
engine coolants mixed with alcohol or methanol
antifreeze. Do not use supplemental coolant
additives in your vehicle. These additives may
harm your engine cooling system.The use of an
improper coolant may void the warranty of
your vehicle's engine cooling system.
[SV20325()08/95]
Recycled engine coolant
[SV20350()08/95]
Ford Motor Company recommends that Ford
and Lincoln-Mercury dealers use recycled engine
coolant produced by Ford-approved processes.
Not all coolant recycling processes produce
coolant which meets Ford specification
ESE-M97B44-A, and use of such coolant may
harm engine and cooling system components.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

288 [SV20375()08/95]Always dispose of used automotive fluids in a
responsible manner. Follow your community's
regulations and standards for recycling and
disposing of automotive fluids.
[SV20400()08/95]
Coolant refill capacity
[SV20425()08/95]
To find out how much fluid your vehicle's
cooling system can hold, seeRefill capacities for
fluidsin the Index.
[SV20450()08/95]
Have your dealer check the engine cooling
system for leaks if you have to add more than a
quart (liter) of engine coolant per month.
[SV20475()08/95]
Severe winter climate
[SV20490()08/95]
If you drive in extremely cold climates (less than
-34ÊF [-36ÊC]), it may benecessary to increase
the coolant concentration above 50%. Refer to
the chart on the coolant container to ensure the
coolant concentration in your vehicle is such that
the coolant will not freeze at the temperature
level in which you drive during winter months.
Never increase the engine coolant concentration
above 60%. Leave a 50/50 mixture of engine
coolant and water in your vehicle year-round in
non-extreme climates.
%*
[SV20500(ALL)08/95]
Checking Hoses
*
[SV20600(ALL)10/89]
Inspect all engine and heater system hoses for
deterioration, leaks and loose clamps before
adding or replacing engine coolant. Make
whatever repairs or replacements that are
necessary using Motorcraft parts or their
equivalents.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

289 %
*
[SV20700(ALL)08/95]
Engine Coolant Drain and Flush
*
[SV20800(ALL)10/89]
To drain your vehicle's engine coolant:
*
[SV20900(ALL)03/94]
1. Turn off the engine and let it cool. Fully
depressurize the engine cooling system by
covering the radiator cap with a thick cloth
and turning it slowly counterclockwise to the
first stop. Step back while the pressure
releases.
*
[SV20950(ALL)05/90]
2. Remove the cap.
*
[SV21000(ALL)05/90]
3. Attach a small hose to the drain tube at the
bottom of the radiator.
*
[SV21200(ALL)05/90]
4. Let the engine coolant drain into a suitable
container. Disconnect the lower radiator hose
at the radiator connector and drain any
remaining engine coolant into a container.
*
[SV21225(ALL)05/94]
5. Reconnect the lower radiator hose and close
the radiator drain cock.
*
[SV21250(ALL)05/95]
Proper procedures for flushing the cooling
system can be found in theService Manual.
%*
[SV21300(ALL)08/95]
Engine coolant refill procedure
*
[SV21400(ALL)10/89]
After you have drained the engine cooling
system:
*
[SV21500(ALL)01/89]
1. Fill the radiator with a 50/50 mixture of the
specified engine coolant concentrate and
water. Allow several minutes for trapped air
to escape (bubble out) and for engine coolant
to flow through the radiator.
*
[SV21900(ALL)03/94]
2. Replace the radiator cap to its fully installed
position, then back off to the first stop. This
will prevent high pressure from building up
in the cooling system during this part of the
fill procedure.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

290 [SV22000(ALL)03/91]3. Turn the heater (temperature and mode
selection) knobs to maximum heat positions
and operate the engine at fast idle
(approximately 2000 RPM) for three to four
minutes.
*
[SV22200(ALL)05/95]
4. Shut off the engine and allow the engine to
cool. Cover the radiator cap with a thick
cloth and cautiously remove it. Step back
while the pressure releases.
[SV22300(ALL)05/89]
5. Add the engine coolant mixture to a level
approximately 1 to 1 1/2 inches (38 mm)
below the filler neck seat.
[SV22400(ALL)05/89]
6. Reinstall the radiator cap fully and back off
to the first stop. Once again, turn the engine
at fast idle until the upper radiator hose is
warm and the thermostat is open.
[SV22550(ALL)05/89]
7. Finally, check the radiator and add more
engine coolant if needed, following the
procedures noted above. Reinstall the
radiator cap securely, when finished.
[SV22555(ALL)05/95]
8. If more engine coolant is necessary, remove
the small plug from the top of the engine
coolant recovery reservoir (not the large cap
of the windshield washer reservoir) and add
1.1 quarts (1 liter) of the 50/50 engine
coolant mixture. Replace the plug in its
original position.
*
[SV22565(ALL)08/95]
NOTE: Due to air being trapped in the 4.0L
engine cooling system, it is not
unusual to experiencea4to7ounce
(120 to 210 ml) coolant loss up to 7,500
miles (12,000 km) after initial system
fill.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

291
*
[SV22620(ALL)06/95]
In order to bleed the cooling system properly
after initial fill with coolant, it might need up
to five cycles of:
*
[SV22630(ALL)06/95]
q
heating up the system (thermostat open)
*
[SV22640(ALL)06/95]
q
making sure coolant is at least up to the
cold fill mark of overflow bottle
*
[SV22650(ALL)06/95]
q
letting the coolant cool down (engine
coolant temperature gauge below the N of
NORMAL)
*
[SV22660(ALL)06/95]
q
topping off the coolant overflow bottle to
the cold fill mark
*
[SV22680(ALL)06/95]
If coolant loss continues after 7,500 miles
(12,000 km), consult your Ford Dealer.
%
*
[SV22700(ALL)03/95]
Windshield Washer Fluid and
Wipers
%*
[SV22800(ALL)03/95]
Washer Fluid
*
[SV22900(ALL)01/95]
Check the level of the windshield washer fluid
every time you stop for fuel. The reservoir for
the windshield washer fluid is located in the
engine compartment.
*
[SV23300(ALL)05/95]
RWARNING
Do not put windshield washer fluid in the
container for the engine coolant.
[SV23400(ALL)01/89]
quarter page art:0020358-A
Windshield washer reservoir
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

297 %
*
[SV26450(ALL)03/95]
Traction-Lok Rear Axle (If equipped)
*
[SV26460(ALL)03/95]
This axle provides added drive away traction on
slippery surfaces, particularly when one or more
wheels are on a surface with poor traction.
*
[SV26470(ALL)05/95]
RWARNING
To avoid injury, never run the engine
with one wheel off the ground, such as
when changing a tire.
%*
[SV26500(ALL)02/95]
Tire Rotation
*
[SV26600(ALL)03/95]
Because your vehicle's front and rear tires
perform different jobs, they often wear
differently. To make sure your tires wear evenly
and last longer, rotate them at the mileage
shown in theMaintenance Schedule and Record
booklet which came with your vehicle.
*
[SV26700(ALL)07/92]
Rotate the tires according to the following
diagram. If you notice that the tires wear
unevenly, have them checked. If your light truck
has a temporary spare tire, do not include it in
the tire rotation pattern.
*
[SV26750(ALL)03/90]
In situations where the tires differ from front to
rear (snow/traction), simply rotate using a side
to side pattern.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

305
*
[SV32700(ALL)02/95]
If the electrolyte level in your battery gets low,
you can add plain tap water to the battery, as
long as you don't use hard water, or water with
a high mineral or alkali content. If possible,
however, try to only fill the battery cell with
distilled water. If the battery needs water often,
have the charging system checked.
%*
[SV32725(ALL)03/95]
Help Us Protect Our Environment
*
[SV32750(ALL)04/95]
Ford Motor Company strongly recommends that
used lead-acid batteries be returned to an
authorized recycling facility for disposal.
*
[SV32775(ALL)03/95]
one inch art:0000983-A
Battery recycling symbol
%*
[SV32900(ALL)05/95]
Because your vehicle's engine is electronically
controlled by a computer, some control
conditions are maintained by power from the
battery. If you ever disconnect the battery, install
a new battery, or experience a dead battery you
must allow the computer to ªrelearnº its idle
conditions before your vehicle will drive
properly. To let the engine do this, put the
gearshift in P (Park), turn off all the accessories,
and start the vehicle. Let the engine idle for at
least one minute.
*
[SV33000(ALL)03/95]
If you do not let the engine relearn its idle, the
idle quality of your vehicle may be adversely
affected until the idle is relearned. Your vehicle
will eventually relearn its idle while you drive
it, but it takes much longer than if you use the
previous procedure.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995