1996 AUDI A4 check oil

01-120


Camshaft Position (CMP) sensor -G40- oily or
dirty on the inside because of leaky seal on cylinder
head

- Remove Camshaft Position (CMP) sensor -G40- and
check for contamination. If it is oily, replace seal on cylinder
head

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test drive, check
DTC memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265

check DTC memory and test drive check DTC
memory
Notes:

The malfunction "P1392 / 17800"is set as soon as the crankshaft position sensor signal is always "high" at an engine
speed between 50 RPM and 4000 RPM and with more than 20 crankshaft sensor signals recognized.
Pa
ge 162 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-121

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1393 / 17801
Ignition Coil Power
Output Stage 1
Electrical Malfunction
-----------------------
P1394 / 17802
Ignition Coil Power
Output Stage 2
Electrical Malfunction
-----------------------
P1395 / 17803
Ignition Coil Power
Output Stage 3
Electrical Malfunction
----------------------- Harness connector for Power output stage
-N122- for ignition coils loose or corroded
due to moisture in the harness connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 28
-
7

Malfunction cause found: Yes

- Erase DTC memory, test drive and after
Pa
ge 163 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
test drive, check DTC memory again

Wiring connection to Power output stage -
N122- for ignition coils or -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
check DTC memory and
test drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 164 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-178
Test table display group 005 and/or display group 006 Display
fields Display on
VAG 1551
scan tool Malfunction cause
Malfunction repair
1, 2, 3, 4 Low oxygen
sensor learning
values
If first learning value in display field 1 is low, but
learning value in display fields 2, 3 and 4 normal:
oil dilution (large amount of fuel in the oil), fuel
injector leaks - Pull off cylinder block breather hose
and close
- If problem disappears after drive on
expressway and/or oil change
- Check fuel injector page 24
-29
If all four oxygen sensor learning values very low
overall:
- Fuel system pressure too high
- EVAP canister purge regulator valve -N80- open
continuously - Check system and residual pressure
page 24
-20

- Check -N80- page 24
-58
and/or
display group 009, display field 3
and/or display group 001, display field
2


Mass Air Flow (MAF) sensor -G70- faulty
Oxygen sensor (O2S) heating faulty or Heated
Oxygen Sensor (HO2S) dirty - Check MAF sensor -G70 page 24
-
81

- Check HO2S and O2S heating
page 24
-49
and/or display group 010,
display fields 1 and 2
Pa
ge 250 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-198
Display groups 015 and 016
Notes on display fields 2, 3 and 4:
If there is a difference of more than a factor of 3 between the lowest and the highest knock sensor signal in one display group,
the following malfunction is possible:

Corrosion on the harness connector
If there are differences of more than 50% in knock sensor signal between display group 015 (cylinders 1 to 3) and display
group 016 (cylinders 4 to 6), the following malfunctions are possible:
Corrosion on the harness connector
Open circuit
Knock sensor faulty
If no malfunctions are found during the electrical testing of the knock sensor, the wiring and the connections, the engine
should be checked for loose subassemblies or engine damage (e.g. oil burning due to faulty piston) Display groups 013
and/or 014.
Pa
ge 279 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1