1996 AUDI A4 check engine

01-43
Notes:

During Output DTM on vehicles with Control Head (E87) Part Number 8D0 820 043 D, A/C Compressor Clutch (N25) DTC
"01270, mechanical malfunction SP" may be stored even though no malfunction is present. Corrective action: When
output DTM is complete, check DTC memory. If above DTC is present, erase DTC memory.
When starting Output DTM, temperature and air distribution flap flap motors move to pre-determined positions in
preparation for individual tests: Temperature Regulator Flap Motor V68: moves to "heat" position. Central Air Flap Motor -
V70- moves to "floor & defroster outlet" position. Footwell Defroster Flap Motor V85 moves to "defrost" position.
Output DTM can be repeated several times, if necessary.
During Output DTM, vehicle must not be moved and engine speed must be less than 3000 rpm.
During Output DTM, A/C system control is switched off and all segments in both A/C control head displays are actuated.
Interior temperature sensor fan -V42- is activated via an A/C control head:
with one display after activation of the coolant fan.
with two displays after activation of air flow flap motor.
Outside air temperature display -G106- is activated via an A/C control head
with one display after activation of air flow flap motor.
with two displays after activation of idle regulation.
Pa
ge 59 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-44

Starting output Diagnostic Test Mode (DTM)

- Start engine, switch on compressor (press
"Auto" button), adjust air flow to center
instrument panel outlets only.

- Connect Scan Tool VAG1551 or 1552 in
operating mode -1-, enter address word 08 "A/C
Heating Electronics" and move forward in
program until "select function XX" appears in the
display.

- Switch on printer by pressing the PRINT button
(indicator lamp in button comes on).

- Check DTC memory page 01
-18
.

- Note any stored DTCs for reference and move
forward in program until "select function XX"
appears in the display. Rapid data transfer
HELP
Select function XX

Indicated on display (function selection)
- Press buttons -0- and -3-.
Rapid data transfer
Q
03 - Output Dia
gnostic Test Mode

Indicated on display
- Press -Q- button to confirm input.
Pa
ge 61 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-45

Notes:

If a DTM component fails to respond as
specified, perform all corrective actions, checks
and tests recommended in output DTM table
page 01
-46
.

A/C system component locations: engine
compartment page 87
-96
(note specific
model year information).

A/C system component locations: passenger
compartment page 87
-106
(note specific
model year information).

Output DTM can be ended by pressing the -C-
button.
After ending output DTM, check DTC memory
page 01
-18
.

If the readout "function unknown or cannot be
carried out at the moment" appears in the
display at the start of output DTM, e.g. when
engine not running, press button and once
again select "function 03 Output Diagnosis Test
Mode (DTM)" (DTM component "A/C Clutch
N25" is no longer actuated for this test).
Pa
ge 63 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-54

Notes:

For m.y. 1996, because A/C engine coolant
temperature sensor G110 is not installed on
USA/CDN models, during basic setting, DTC
"00799 engine coolant temperature sensor
G110" is stored and must be erased.
For m.y. 1997 A/C engine coolant temperature
(ECT) sensor -G110- is deleted, and will no
longer load a DTC when checking DTC memory
after ending basic setting.

- Check DTC memory page 01
-18
.

- Erase DTC memory (function 05) and end
output (function 06) page 01
-55
.
Pa
ge 76 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-60

CAUTION!

Part numbers are for reference only.
Always check with your Parts Dept. for the
latest information.
Coding example:

- Enter code "00062" by pressing applicable
buttons on key pad of VAG1551.
Code Control ModuleEnter code number 00062

Indicated on display
Notes: - Press -Q- button to confirm input.
- Perform basic setting page 01
-52
.
Nippondenso A/C compressors must have A/C control head Part No.
index "H" installed to allow coding "00162." If an unrecognized code is entered in a control head, it is suppressed
and coding "00042" (4-cyl. gasoline engine USA) is then stored. When replacing an A/C control head, always refer to the most recent
parts information.
Pa
ge 87 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1