1995 VOLKSWAGEN PASSAT teves

Downloaded from www.Manualslib.com manuals search engine 46-9

4 - Retaining spring Insert in both brake
caliper housing
drillings
5 - Brake carrier Supplied as
replacement part
assembled with
sufficient amount of
grease on guide pins If protective caps are
damaged use repair kit Use grease packet
supplied to lubricate
guide pins
6 - Brake caliper housing Do not disconnect
brake hose when
changing brake pads Removing and
installing Page 46-12 Page 2 of 7Front brakes, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.2

Downloaded from www.Manualslib.com manuals search engine 46-10

7 - Guide pins, 25 Nm (18
ft lb) Removing and
installing from
Page 46-12 8 - Protective cap
9 - Seal Always replace Pry out with suitable
tool
10 - Brake hose
11 - Banjo bolt, 30 Nm (22 ft lb)
12 - Ribbed bolt, 125 Nm
(92 ft lb)
13 - Wheel bearing housing 14 - Hex socket head bolt,
10 Nm (7 ft lb)
15 - Speed sensor Only on vehicles with
ABS Before inserting
sensor, clean
mounting hole inner
surface and coat with
lubricating paste, G
000 650 Page 3 of 7Front brakes, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.2

Downloaded from www.Manualslib.com manuals search engine 46-11

16 - Splash plate
17 - Hex bolt, 10 Nm (7 ft lb) 18 - Speed sensor rotor Only on vehicles with
ABS
19 - Hub Removing and
installing Page 40-14 20 - Countersunk bolt Page 4 of 7Front brakes, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.2

Downloaded from www.Manualslib.com manuals search engine 46-12

Brake pads, removing and installing

Removing

Note:
If reusing brake pads mark location and install in
same position or uneven braking may result. - Remove protective caps. - Pry off brake pad retaining spring from brake
caliper housing with a screwdriver and remove. Page 5 of 7Front brakes, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.2

Downloaded from www.Manualslib.com manuals search engine 46-13
Installing
Note:
Before installing new brake pads, press piston back
into the cylinder with resetting tool. Before pressing
the piston back, remove some brake fluid from the
reservoir with a bleeder bottle. If reservoir has been
topped up, fluid may overflow and cause damage. - Remove both guide pins from brake caliper. - Remove brake caliper housing and lay to one side
so that weight of brake caliper does not stress or
damage brake hose.
- Take brake pads out of brake caliper housing or
from brake carrier. - Pressing piston back. Page 6 of 7Front brakes, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.2

Downloaded from www.Manualslib.com manuals search engine 46-14

- Install brake pad with retaining spring in brake
caliper housing (piston).

- Install outer brake pad in brake carrier.
- Secure brake caliper housing with both guide
pins to brake carrier.

- Install both protective caps.
- Install retaining spring into brake caliper
housing.

Note:
After replacing the brake pads, depress brake
pedal firmly several times with the vehicle
stationary, so that the brake pads are proper/y
seated in their normal operating position. Page 7 of 7Front brakes, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.2

Downloaded from www.Manualslib.com manuals search engine 47-10

Front brake caliper,
servicing
(Teves/Ate)
Note: When repairing install all
parts supplied in repair kit. Apply thin coat of brake
cylinder paste to brake
cylinders, pistons and
seals.
1 - Protective seal Push onto bleed valve 2 - Bleed valve Apply thin coat of brake cylinder paste to threads before
threading in
3 - Cap Install in mounting
bushing
4 - Guide pin, 25 Nm (18 ft
lb)
5 - Mounting bushing Insert into brake
caliper housing Page 1 of 5Front brake caliper, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.47.3

Downloaded from www.Manualslib.com manuals search engine 47-11

6 - Brake cylinder housing 7 - Brake carrier Install on brake caliper
housing
8 - Retaining spring Install with both ends
in the drillings in brake
caliper housing
9 - Piston seal Remove using a
screwdriver Fig. 2 10 - Piston Force piston out of
brake caliper using
compressed air Fig. 1 Installing Fig. 3 and
Fig. 4 and Fig. 5 First coat the piston
lightly with brake
cylinder paste. Piston diameter 54
mm
11 - Protective seal Do not damage when
installing piston Page 2 of 5Front brake caliper, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.47.3