1995 TOYOTA SUPRA wheel bolt torque

TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 STEERING COLUMN   
  Steering wheel set nut 35 360 26  Steering wheel pad set screw 7.1 72 62 in.Vlbf  Column assembly set nut 25 260 19 
 Intermediate shaft x Sliding yoke
 
35
 
360
 
26 
  Tilt memory bolt x Square nut
 
 6.4
 
 65
 
 56 in.Vlbf
  Tilt lever assembly set screw 4.7 48 42 in.Vlbf
  Tilt pawl set nut 5.9 60 52 in.Vlbf
  Tilt lever retainer set nut 15 150 11
  Tilt memory bolt set nut 5.9 60 52 in.Vlbf
  Turn signal bracket set bolt 8.8 90 78 in.Vlbf
  Sliding yoke 35 360 26
  Compression set screw 6.4 65 56 in.Vlbf PS VANE PUMP   
  PS vane pump set bolt 58 590 42 
  Union bolt
 
 49
 
 500
 
 36
  Vane pump pulley set nut 43 440 32
  Front housing x Rear housing 17 170 12
  Pressure port union 83 850 61
  Oil reservoir set bolt (2JZ±GE) Front side bolt 13 130 9
 Rear side bolts 17 170 12
  Suction port union set bolt (2JZ±GTE) 13 130 9
 PS GEAR HOUSING   
  Tie rod end x Steering knuckle 49 500 36  Control valve shaft x Intermediate shaft 35 360 26  Pressure feed and return tube set union bolts 49 500 36 
  Gear housing set bolt and nut
 
 75
 
 770
 
 55
  Pressure control valve assembly x Control valve housing 18 185 13
  Control valve housing set bolt 18 185 13
  Self±locking nut 39 400 29
  Rack housing cap 69 700 501
  Rack guide spring cap lock nut 56 567 41
  Rack end 90 914 66
  Tie rod end lock nut 56 570 41  Turn pressure tube union nut 24 243 17  Turn pressure tube union bolt 34 350 25
SR±52± STEERINGSERVICE SPECIFICATIONS

PREPARATION
SST (SPECIAL SERVICE TOOLS)
SRS Airbag Deployment Tool
Diagnosis Check Wire
Puller C SetSteering wheel
RECOMMENDED TOOLS
Torx Socket T30
Torx Socket T40
TOYOTA Electrical Tester Set
Steering wheel pad
Center airbag sensor assembly
EQUIPMENT
 
 Torque wrench 
 
 
 Bolt: Length: 35 mm (1.38 in.) Pitch: 1.0 mm (0.039 in.)
Diam.: 6.0 mm (0.236 in.) 
 Airbag disposal
 
 
Tire Width: 185 mm (7.28 in.) Inner diam.: 360mm (14.17 in.) 
 
Airbag disposal
 
 
Tire with disc wheel Width: 185 mm (7.28 in.)
Inner diam.: 360 mm (14.17 in.) 
 
Airbag disposal
 
 
Vinyl bag 
 
Airbag disposal
± SUPPLEMENTAL RESTRAINT SYSTEMPREPARATIONRS±9

5. ADJUST CAMBER AND CASTER
(a) Remove the engine under cover.
(b) Remove the nut, 2 bolts and front lower arm bracket stay.
(c) Loosen the front and/or rear adjusting cam nuts.
(d) Adjust the camber and caster by front and/or rear adjusting
cams. (See adjustment chart)
Specifications
  2JZ±GE 2JZ±GTE
 Camber
Left±right error ±0°20' + 30'
30' or less ±0°30' + 30'
30' or less
 
 Caster
Left±right error 
 3°20' + 30'
30' or less 
 3°30' + 30'
30' or less
(e) Torque the front and/or rear adjusting cam nuts.
Torque: 226 NVm (2,300 kgfVcm, 166 ftVlbf)
(f) Install the front lower arm bracket stay.
Torque:
Nut: 43 NVm (440 kgfVcm, 32 ftVlbf)
Bolt: 59 NVm (600 kgfVcm, 43 ftVlbf)
(g) Install the engine under cover.
6. ADJUST TOE±IN
(a) Remove the boot clamps.
(b) Loosen the tie rod end lock nuts.
(c) Turn the left and right tie rod ends an amount to adjust the
toe±in.
Toe±in (total):
A+ B: 0° + 0.1°
C±D: 0 + 1 mm (0 + 0.04 in.)
HINT: Ensure that the lengths of the left and right tie rods are
the same.
Tie rod end length left±right error:
Less than 1.5 mm (0.059 in.)
(d) Tighten the tie rod end lock nut.
Torque: 56 NVm (570 kgfVcm, 41 ftVlbf)
(e) Place the boot on the seat and clip it.
HINT: Ensure that the boots are not twisted.
± SUSPENSION AND AXLEWHEEL ALIGNMENTSA±5

(c) Remove the bolt and disconnect the parking brake cable
bracket.
(d) Loosen and adjust the No.1 and/or No.2 cams.
(e) Adjust camber and toe±in by turning the No.1 and / or No.2
cams.
(See adjustment chart)
(f) Torque the No.1 and/or No.2 cam nuts.
Torque: 184 NVm (1,880 kgfVcm, 134 ftVlbf)
(g) Connect the parking brake cable bracket with the bolt. SA±10
± SUSPENSION AND AXLEWHEEL ALIGNMENT

STEERING KNUCKLE WITH AXLE HUB
REMOVAL
Installation is in the reverse order of removal.
INSTALLATION HINT: After installation, check ABS speed
sensor signal and front wheel alignment.
(See page BR±62 and SA±4)
1. REMOVE FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 96 ftVlbf)
2. REMOVE FRONT BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 NVm (1,200 kgfVcm, 87 ftVlbf)
(b) Support the brake caliper securely.
(c) Place matchmarks on the disc and axle hub.
(d) Remove the disc.
3. CHECK BACKLASH IN BEARING SHAFT DIRECTION
Place the dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum:
0.05 mm (0.0020 in.)
If greater than the specified maximum, replace the bearing.
4. CHECK AXLE HUB DEVIATION
Using a dial indicator, check the deviation at the surface of
the axle hub outside the hub bolt.
Maximum:
0.05 mm (0.0020 in.)
If greater than the specified maximum, replace the axle hub.
5. DISCONNECT ABS SPEED SENSOR FROM STEERING
KNUCKLE
Remove the bolt and disconnect the sensor from the steering
knuckle.
Torque: 8 NVm (80 kgfVcm, 69 inVlbf)
SA±16± SUSPENSION AND AXLEFRONT AXLE HUB

(b) Using SST and a press, press the axle hub to steering
knuckle.
SST 09608±32010, 09608±35014 (09608±06040)
4. INSTALL ABS SPEED SENSOR ROTOR ON AXLE SHAFT
NOTICE: Do not scratch the serrations of the sensor ro-
tor.
5. INSTALL AXLE HUB LOCK NUT
(a) Install and torque a new axle hub lock nut.
Torque: 199 NVm (2,030 kgfVcm, 147 ftVlbf)
(b) Using a chisel and hammer, stake the lock nut.
6. INSTALL HUB GREASE CAP
Using a screwdriver and hammer, install the hub grease cap
to the steering knuckle.
FRONT WHEEL HUB BOLT
REPLACEMENT
1. REMOVE FRONT WHEEL
2. REMOVE FRONT BRAKE CALIPER AND DISC
(See page SA±16)
3. REMOVE HUB BOLT
Using SST, remove the hub bolt.
SST 09628±10011
4. INSTALL HUB BOLT
(a) Install washer and nut to a new hub bolt, as shown in the
illustration.
(b) Turn the wheel nut to pull the hub bolt through until the
underside of the hub bolt head touches the axle hub.
5. INSTALL FRONT BRAKE DISC AND CALIPER
(See page SA±16)
6. INSTALL FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
± SUSPENSION AND AXLEFRONT AXLE HUBSA±19

FRONT SHOCK ABSORBER REMOVAL
Installation is in the reverse order of removal.
INSTALLATION HINT: After installation, check ABS speed
sensor signal and front wheel alignment.
(See page BR±62 and SA±4)
1. REMOVE FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
2. REMOVE DISC BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 NVm (1,200 kgfVcm, 87 ftVlbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE
HARNESS
(a) Remove the bolt and disconnect the speed sensor from the
steering knuckle.
Torque: 8 NVm (80 kgfVcm, 69 in.Vlbf)
(b) Remove the 3 bolts and disconnect the wire harness clamp
to prevent the wire harness being damaged when removing
or installing the through bolt.
4. REMOVE FRONT FENDER SPLASH SHIELD
5. LH side only.
MOVE WASHER TANK
(a) Remove the 2 washer tank set bolts.
(b) Move the washer tank from the body.
6. DISCONNECT UPPER SUSPENSION ARM
(a) R e m o v e t h e b o l t a n d n u t a n d d i s connect the upper
suspension arm from the subframe.
Torque: 164 NVm (1,670 kgfVcm, 121 ftVlbf)
INSTALLATION HINT: After stabilizing the suspension,
torque the nut.
(b) Support the upper suspension arm securely. SA±22
± SUSPENSION AND AXLEFRONT SUSPENSION

UPPER SUSPENSION ARM REMOVAL
Installation is in the reverse order of removal.
INSTALLATION HINT: After installation, check ABS speed
sensor signal and front wheel alignment.
(See page BR±62 and SA±4)
1. REMOVE FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
2. REMOVE DISC BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 NVm (1,200 kgfVcm, 87 ftVlbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE
HARNESS CLAMP
(a) Remove the bolt and disconnect the speed sensor from the
steering knuckle.
Torque: 8 NVm (80 kgfVcm, 69 in.Vlbf)
(b) Remove the 3 bolts and wire harness clamp to prevent the
wire harness being damaged when removing or installing the
through bolt.
4. DISCONNECT UPPER SUSPENSION ARM
(a) Remove the cotter pin and the nut.
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
(b) Using SST, disconnect the upper suspension arm from the
steering knuckle.
SST 09628±62011
5. REMOVE FRONT FENDER SPLASH SHIELD
6. LH side only:
MOVE WASHER TANK
(a) Remove the 2 washer tank set bolts.
(b) Move the washer tank away from the body.
± SUSPENSION AND AXLEFRONT SUSPENSIONSA±27