1995 TOYOTA SUPRA wheel bolt torque

ENGINE & TRANSMISSION ASSEMBLY
1. A/T:
CHECK TORQUE CONVERTER CLUTCH INSTALLATION
Using calipers and straight edge, measure from the installed
surface of the torque converter clutch to the front surface of
the transmission.
Correct distance:
Less than 0.1 mm (0.004 in.)
If the distance is not as specified, check for an improper
installation.
2. 2JZ±GE M/T:
INSTALL CLUTCH DISC AND COVER
(a) Insert SST in the clutch disc, and then set them and the cover
in position.
SST 09301±00110
(b) Align the matchmarks on the clutch cover and flywheel.
(c) Tighten the bolts evenly and gradually while pushing SST.
Make several passes around the cover until it is snug.
SST 09301±00110
(d) Torque the bolts on the clutch cover in the order shown.
Torque: 19 NVm (195 kgfVcm, 14 ftVlbf)
3. ASSEMBLE ENGINE AND TRANSMISSION
(a) M/T:
Align the input spline with the clutch disc and install the trans-
mission to the engine.
(b) Align the 2 knock pins on the cylinder block with the pin holes
of the clutch housing.
(c) Install the transmission with the 6 bolts.
Torque:
14 mm head
39 NVm (400 kgfVcm, 29 ftVlbf)
17 mm head
72 NVm (730 kgfVcm, 43 ftVlbf)
EG±124± ENGINEENGINE MECHANICAL

 Connecting rod cap X Connecting rod 1st
2nd 29
Turn 905 300 22
 
Oil nozzle X Crankshaft (2JZ±GTE)
 
8.8
 
90
 
78 in.Vlbf Rear oil seal retainer X Cylinder block 5.9 60 52 in.Vlbf Crankshaft position sensor X Cylinder block (2JZ±GTE) 8.8 90 78 in.Vlbf Engine mounting bracket X Cylinder block 58 590 43 Engine coolant drain plug X Cylinder block 29 300 22 Union for oil cooler X Cylinder block (2JZ±GTE) 39 400 29
 Knock sensor X Cylinder block 44 450 33
 Oil pressure switch X Cylinder block 14 150 11
 Fuel pipe support X Cylinder block 14 145 10
 Oil filter bracket X Cylinder block 88 900 65
 No.2 water bypass pipe X Water pump 21 210 15
 No.2 water bypass pipe X Cylinder block 21 210 15
 Flywheel X Crankshaft (M/T) 1st
2nd 49
Turn 905 500 36
 Drive plate X Crankshaft (A/T) 83 850 61 Clutch cover X Flywheel (M/T) 19 195 14 
 Cylinder block X Transmission 14 mm head
17 mm head 
 39
72 
 400
730 
 29
43
 Clutch service hole cover X Clutch housing (2JZ±GTE M/T) 12 120 9
 Drive plate X Torque converter clutch (A/T) 33 340 25
 Oil cooler tube X Union for transmission (A/T) 34 350 25
 Rear support member X Body 25 260 19
 Rear support member X Engine rear mounting insulator 13 135 10
 Front suspension crossmember X Engine mounting insulator 59 600 43
 Transmission shift lever X Shift lever retainer (M/T) 19 195 14
 Transmission control rod X Shift lever (A/T) 13 130 9
Clutch release cylinder X Transmission (M/T)131309 
Clutch line tube X No.1 oil pan
 
37
 
380
 
27 Ground strap X Transmission (M/T) 37 380 27 Fuel inlet hose X Fuel pipe support 29 300 22 
 A/C compressor X Cylinder block for stud bolt
for bolt and nut 
 26
52 
 265
530 
 19
38
 PS pump front bracket X Cylinder block (2JZ±GE) 58 590 43
 PS pump front bracket X Oil pump (2JZ±GE) 52 530 38
 PS pump housing X PS pump bracket 58 590 43
 PS pump bracket X A/C compressor 58 590 43
 PS pump bracket X Cylinder block 39 400 29
 PS pump rear stay X PS pump bracket 39 400 29
 PS pump rear stay X Intake manifold stay (2JZ±GE) 39 400 29
 Rear center floor crossmember brace X Body (2JZ±GTE) 28 290 21
No.2 front exhaust pipe X Exhaust manifold6263046 No.2 front exhaust pipe X Front exhaust pipe 58 590 43 Pipe support bracket X Transmission 43 440 32 Front exhaust pipe X Center exhaust pipe 58 590 43 Center exhaust pipe X Tailpipe 19 195 14 
 
Sub heated oxygen sensor
x Front exhaust pipe (2JZ±GE (California), 2JZ±GTE) 
 
20 
 
200 
 
14
± ENGINEENGINE MECHANICALEG±139

(g) Install the retainer clamp.
(h) Connect the connector and hoses to the fuel pump bracket:
wFuel pump connector
wFuel outlet hose
Connect the outlet hose with 2 new gaskets and the union
bolt.
Torque: 29 NVm (300 kgfVcm, 22 ftVlbf)
wFuel return hose
wFuel breather hose
2. REMOVE SERVICE HOLE COVER
3. REMOVE SPARE WHEEL
4. REMOVE SPARE WHEEL COVER
5. TAKE OUT FLOOR CARPET
6. CHECK FOR FUEL LEAKS
(See item 5 in fuel system in precaution)
± ENGINESFI SYSTEM (2JZ±GE)EG±199

(e) Temporarily install the retainer.
(f) Using SST, tighten the retainer until the arrow mark on
retainer is within the lines on the fuel tank.
SST 09808±14010
(g) Check that the arrow marks of the fuel pump bracket and fuel
tank are aligned.
(h) Install the retainer clamp.
(i) Connect the connector and hoses to the fuel pump bracket:
wFuel pump connector
wFuel outlet hose
Connect the outlet hose with 2 new gaskets and the union
bolt.
Torque: 29 NVm (300 kgfVcm, 22 ftVlbf)
wFuel return hose
wFuel breather hose
2. INSTALL SERVICE HOLE COVER
3. INSTALL SPARE WHEEL
4. INSTALL SPARE WHEEL COVER
5. INSTALL FLOOR CARPET
6. CHECK FOR FUEL LEAKS
(See item 5 in fuel system in precaution) EG±270
± ENGINESFI SYSTEM (2JZ±GTE)

(09957±04010)
09950±40010
(09958±04010)
09950±50010
(09951±05010)
(09952±05010)
(09953±05020)
(09954±05020)
09960±10010
Puller B Set
Attachment
Holder
Puller C Set
Slide Arm
Hanger 150
Center Bolt 150
Variable Pin Wrench Set
Claw No.2
Vane pump pulley
Main shaft assembly
Main shaft assembly
RECOMMENDED TOOLS
Total preload
Steering wheel pad
Compression spring
Snap Ring No.1 Expander
TOYOTA Electrical Tester Set
Torx Socket T30
Torque Wrench (30 kgf
cm)09025±00010
09042±00010
09082±00050
09905±00012
± STEERINGPREPARATIONSR±5

STEERING COLUMN INSTALLATION
1. INSTALL STEERING COLUMN ASSEMBLY
(a) Torque the 4 column assembly set nuts.
Torque: 25 NVm (260 kgfVcm, 19 ftVlbf)
(b) Install the brake pedal return spring.
(c) Align the matchmarks on the intermediate shaft and control
valve shaft.
(d) Torque the bolt A.
Torque: 35 NVm (360 kgfVcm, 26 ftVlbf)
(e) Torque the bolt B.
Torque: 35 NVm (360 kgfVcm, 26 ftVlbf)
2. INSTALL COMBINATION SWITCH
(a) Tighten the 4 screws.
(b) Connect the 4 connectors and airbag connector.
3. INSTALL THESE PARTS:
(See page BO±45)
(a) Register No.2 duct
(b) Finish panel lower LH
(c) Finish panel lower
(d) Cluster finish panel center
(e) Cluster finish panel LH
(f) Cluster finish panel RH
(g) Cluster finish panel
(h) Console panel upper
4. INSTALL UPPER AND LOWER COLUMN COVER
Tighten the 5 screws.
5. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the spiral cable counterclockwise by hand until it
becomes harder to turn the cable.
(c) Then rotate the spiral cable clockwise about 3 turns to align
the red mark.
HINT: The spiral cable will rotate about 3 turns to either left
or right of the center.
6. INSTALL STEERING WHEEL
(a) Align the matchmarks on the wheel and main shaft.
(b) Torque the wheel set nut.
Torque: 35 NVm (360 kgfVcm, 26 ftVlbf)
(c) Connect the connector.
± STEERINGTILT STEERING COLUMNSR±21

(c) Using a brass bar and hammer, stake the washer.
NOTICE: Avoid any impact to the rack.
16. INS TALL RH AND LH RACK BO O TS , CLAMP S AND
CLIPS
(a) Ensure that the steering rack hole is not clogged with grease.
HINT: If the hole is clogged, the pressure inside the boot will
change after it is assembled and the steering wheel turned.
(b) Install the boot.
NOTICE: Be careful not to damage or twist the boot.
(c) Install the clamp and clip to the boot.
HINT: When the rack guide spring cap is towards you, install
the clip and clamp in the positions shown in the illustration.
17. INSTALL TIE ROD ENDS
(a) Screw the lock nut and tie rod end onto the rack end until the
matchmarks are aligned.
(b) After adjusting toe±in, torque the nut.
Torque: 56 NVm (570 kgfVcm, 41 ftVlbf)
18. INSTALL TURN PRESSURE TUBES
(a) Install 2 new union seats.
(b) Using SST, install the 2 tubes.
SST 09633±00020
Torque: 24 NVm (243 kgfVcm, 17 ftVlbf)
HINT: Use a torque wrench with a fulcrum length of 300 mm
(11.81 in.)
(c) Torque the 2 union bolts over 4 new gaskets.
Torque: 34 NVm (350 kgfVcm, 25 ftVlbf)
POWER STEERING GEAR
INSTALLATION
1. INSTALL POWER STEERING GEAR ASSEMBLY
(a) Temporarily install the 2 bolts and nuts.
(b) After installing the rack housing bracket and grommet, torque
the 2 bolts and nuts.
Torque: 75 NVm (770 kgfVcm, 55 ftVlbf)
± STEERINGPOWER STEERING GEARSR±45

2. INSTALL RACK HOUSING BRACKET AND GROMMET
Torque the 2 bolts and nuts.
Torque: 75 NVm (770 kgfVcm, 55 ftVlbf)
3. CONNECT PPS SOLENOID CONNECTOR
4. CONNECT PRESSURE FEED TUBE
Torque the union bolt over a new gasket.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
5. CONNECT RETURN TUBE
Torque the union bolt over 2 new gaskets.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
6. CONNECT RH AND LH TIE ROD ENDS
(See page SA±17)
7. CONNECT INTERMEDIATE SHAFT
(See page SR±21)
8. INSTALL FR SUSPENSION MEMBER PROTECTOR
Torque the 4 bolts.
9. INSTALL ENGINE UNDER COVER
Install the 10 screws.
10. BLEED POWER STEERING SYSTEM
(See page SR±9)
11. CHECK FRONT WHEEL ALIGNMENT
(See page SA±4) SR±46
± STEERINGPOWER STEERING GEAR