1995 RENAULT MEGANE SCENIC height

33
REAR AXLE
Underbody heights for four bar rear axle

GLAZING
Front door window
Fit the window flush with the fixed window pillar
seal (C).
The height of the window is adjusted by moving
the stop (7) of the window mechanism toothed
wheel.
54
Tighten the upper pillar bolt (6).
Open the door and tighten the lower pillar
mounting (6).
Position the fixed window fully in the pillar
groove.
Fit the window flush with the pillar seal (A) and
with a protrusion (B = 1 mm) with the exterior
mirror seal.Tighten the mounting bolts (5).
Tightening torque of all mounting bolts 8 N.m.
MM M M
OO O O
VV V V
AA A A
BB B B
LL L L
EE E E

WW W W
II I I
NN N N
DD D D
OO O O
WW W W
12281-1R1
12281-1R2
12277-2R
12469R
54-3

59
INTERIOR SAFETY ACCESSORIES
Height adjustment mechanism (A)

NON-SIDE OPENING ELEMENTS
Tailgate
REMOVAL
Remove the trim and disconnect the various wi-
ring harnesses (see sections 52 and 71).
Remove:
- the third stop light,
- the rear screen washer jet pipe,
- the wiring harness,
99386R1
48A
PRE4803
- the headlining plugs using a screwdriver (torx
20).
99621R2
Unclip the tailgate balancers at (A).
Remove the mounting nuts and remove the
hinges (B) (two persons required for this opera-
tion).
NOTE : if the tailgate or the roof is being repla-
ced, retain the height adjustment shims located
under the hinges (B).
To do this, use a cutting tool to destroy the finis-
hing seal around the shims and retain them.
The hinges are welded on the tailgate, so these
shims of thickness 1 mm are used to adjust the
clearance between the roof and the tailgate.
48-1

WINDOWS
Rear screen
54B
Preparation of the bonding areas is described in
the general method for bonding windows,
Technical Note n° 371A.
15404R1
Fit the shims from the Parts Department (1)
These shims are in two sections:
- section (1) ensures the height positioning of
the window at the bottom only
- section (2) ensures the depth positioning of
the window in the tailgate frame.
Fit parts (2) of the shim into holes (E) in the tail-
gate and rest part (1) on the edge of the tailgate
lip.
Fit part (2) into tailgate holes (D) only.
90989S
After applying the bead of adhesive to the win-
dow, offer up the window, centring it in relation
to the window washer jet and the reference mark
on the window.
Rest the bottom of the window on the height po-
sitioning shims (1) (see above).
Flatten the window against the depth positioning
shims (2).
Hold the upper part of the window using strips of
masking tape while the adhesive dries .
NOTE: Remember to remove the height adjus-
tment section (1) when the vehicle is no longer im-
mobilised.
54-5

WINDOWS
Rear quarter panel window
54C
After removing the window, remove the parts (B)
of the retaining clips for the inner linings fitted
onto the wing panel lip.
Remove the positioning shims and flatten the ma-
stic bead using a cutting tool.
Refit the clips (B).
15405R
BONDING AND FITTING THE WINDOW
IMPORTANT:
before refitting the window, if ne-
cessary, refit the door seal under the window.
15404R1
Fit the shims from the Parts Department (1).
These shims are in two sections:
- section (1) ensures the height and length posi-
tioning of the window at the bottom and the
rear,
- section (2) ensures the depth positioning of
the window.
15403R1
54-7

WINDOWS
Rear quarter panel window
54C
Preparation of the bonding areas is described in
the general method for bonding windows,
Technical Note n° 371A.
90989S
After applying the bead of adhesive to the win-
dow, offer up and set the window against the
shims mounted at (E).
Rest the lower part of the window on the height
positioning shims (1).
Flatten the window against the depth positioning
shims (2).
Hold the upper part of the window using strips of
masking tape while the adhesive dries .
NOTE:remember to remove the height adjus-
tment section (1) when the vehicle is no longer im-
mobilised. Fit the shim part (2) in holes (E).
Rest part (1) on the edge of the quarter panel win-
dow lip.
Fit part (2) only into hole (D).
54-8

LOWER STRUCTURE
Acceleration sensor mounting
41SAcceleration sensor mounting
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor.
For standardisation purposes, the centre floor is
delivered by the Parts Department without the
acceleration sensor mounting.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
1
2
3
4
5Acceleration sensor mounting
Front seat height adjuster
Front seat height adjuster reinforcement
Centre floor
Tunnel stiffener 1.2
1.5
1.5
1
1
41-16
Z