1995 MITSUBISHI 3000GT wirin g

oil roof rack climate control drain bolt radiator key

Page 21 of 738

MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine GENERAL - Junction Block19
/
L
To roofwiring -harness
Front
/ITo frontwiring harness
- TO instrument panel
wiring harness
Theft-
alarm
horn
rel

Page 29 of 738

MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine GENERAL - How to Diagnose27
HOW TO DIAGNOSE
L;The most important point in troubleshooting is to determine “Probable Causes”. Once the proba

Downloaded from www.Manualslib.com manuals search engine GENERAL - How to Diagnose27
HOW TO DIAGNOSE
L;The most important point in troubleshooting is to determine “Probable Causes”. Once the probable causes
are determined, parts to be checked can be limited to those associated with such probable causes. Thereforeunnecessary checks can be eliminated. The determination of the probable causes must be based
ona theory and be supported by facts and must not be based on intuition only.
TROUBLESHOOTING STEPSIf an attempt is made to solve a problem without going through correct steps for troubleshooting, the
problem symptoms could become more complicated, resulting in failure to determine the causes correctly
and making incorrect repairs. The four steps below should be followed in troubleshooting.
I i
,;zirvation of Problem Symp-Determination of Probable
CausesI
Observe the symptom carefully.
Check if there are also other problems.
In determining the probable causes, it is necessary to check
the wiring diagram to understand the circuit as a system.
Knowledge of switches, relays and other parts is necessary
for accurate determination. The causes of similar problems
in the past must be taken into account.
After the problems are corrected, be sure to check that
the system operates correctly. Also, check that new prob-
lems have not been caused by the repair.
INFORMATION FOR DIAGNOSIS
Troubleshooting is carriedout by making step by step
is found. Always go through
what check is to be made where
/
b
This manual contains the cable diagrams as well as the individual circuit drawings, operational explanations,
and troubleshooting hints for each component required to facilitate the task of troubleshooting. The information
is compiled in the following manner:
(1) Cable diagrams show the connector positions, etc., on the actual vehicle as well as the harness path.(2) Circuit drawings show the configuration of the circuit with all switches in their normal positions.
(3) Operational explanations include. circuit drawings of voltage flow when the switch is operated and
how the component operates in reaction.
(4) Troubleshooting hints include numerous examples of problems which might occur, traced backwardin a common-sense manner to the origin of the trouble.
Problems whose origins may not be found in this manner are pursued through the various system
circuits.
NOTE
Components of MFI, ETACS, ECS, etc. with ECU do not include 3 and 4 above. For this information,
refer to a manual which includes details of these components.
TSB Revision

Page 33 of 738

MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine iGENERAL
- How to Diagnose31
Normal close (NC) type
Deenergized stateEnergized state
Current does not flow
Z1680235
State of fuse blown due to

Downloaded from www.Manualslib.com manuals search engine iGENERAL
- How to Diagnose31
Normal close (NC) type
Deenergized stateEnergized state
Current does not flow
Z1680235
State of fuse blown due to overcurrent
/
L
I21680237
State of fuse blown due to thermal fatigue
Z1660236When a normal close type relay as illustrated here is
checked, there should be continuity between terminals
(1) and (2) and between terminals 3 and 4 when the relay
is deenergized, and the continuity should be lost betweenterminals 3 and 4 when the battery voltage is applied
to the terminals
1 and 2. A relay can be checked in this
manner and it cannot be determined if a relay is okay
or faulty by checking its state only when it is deenergized
(or energized),
CHECKING FUSESA blade type fuse has test taps provided to allow checking
of the fuse itself without removing it from the fuse block. Thefuse is okay if the test light comes on when its one lead is
connected to the test taps (one at a time) and the other lead
is grounded. (Change the ignition switch position adequatelyso that the fuse circuit becomes live.)
CAUTIONS IN EVENT OF BLOWN FUSE
When a fuse is blown, there are two probable causes as follows:One is that it is blown due to flow of current exceeding its
rating.The other is that it is blown due to repeated on/off current
flowing through it. Which of the two causes is responsible
can be easily determined by visual check as described below.(1) Fuse blown due to current exceeding rating
The illustration shows the state of a fuse blown due to
this cause. In this case, do not replace the fuse with a
new one hastily since a current heavy enough to blow
the fuse has flowed through it. First, check the circuit
for shorting and check for abnormal electric parts. Only
after the correction of such shorting or parts, fuse of the
same capacity should be used as a replacement. Never
use a fuse of larger capacity than the one that has blown.
If such a fuse is used, electric parts or wirings could be
damaged before the fuse blows in the event an overcurrent
occurs again.(2) Fuse blown due to repeated current on/off
The illustration shows the state of a fuse blown due to
repeated current on/off. Normally, this type of problem
occurs after fairly long period of use and hence is less
frequent than the above type. In this case, you may simplyreplace with a new fuse of the same capacity.
1 TSB Revision

Page 34 of 738

MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine 32GENERAL - How to Diaanose
CHECKING CABLES AND WIRES1. Check connections for looseness, rust and stains.
2.Check terminals and wires for corro

Downloaded from www.Manualslib.com manuals search engine 32GENERAL - How to Diaanose
CHECKING CABLES AND WIRES1. Check connections for looseness, rust and stains.
2.Check terminals and wires for corrosion by battery electro-
lyte, etc.
3.Check terminals and wires for open circuit or impending
open circuit.4. Check wire insulation and coating for damage, cracks
and degrading.
5.Check conductive parts of terminals for contact with other
metallic parts (vehicle body and other parts).6. Check grounding parts to verify that there is complete
continuity between attaching bolt(s) and vehicle body.7. Check for incorrect wiring.
8.Check that wirings are so clamped as to prevent contact
with sharp corners of the vehicle body, etc. or hot parts(exhaust manifold, pipe, etc.).
9.Check that wirings are clamped firmly to secure enough
clearance from the fan pulley, fan belt and other rotating
or moving parts.
10. Check that the wirings between the fixed parts such as
the vehicle body and the vibrating parts such as the engine
are made with adequate allowance for vibrations.
HANDLING ON-VEHICLE BATTERY
When checking or servicing does not require power from the
on-vehicle battery, be sure to disconnect the cable from thebattery
(-) terminal. This is to prevent problems that could
be caused by a short circuit. Disconnect the (-) terminal first
and reconnect it last.
Caution1. Before connecting or disconnecting the negative
cable, be sure to turn off the ignition switch and the
lighting switch.
(If this is not done, there is the possibility of semicon-
ductor parts being damaged.)
2.After completion of the work steps [when the battery’s
negative (-)
terminal is connected], warm up the engineand allow it to idle for approximately five minutes
under the conditions described below, in order to sta-
bilize the engine control conditions, and then checkto be sure that the idling is satisfactory.
Engine coolant temperature:
85-95°C (185-203°F)
Lights, electric fans, accessories: OFF
Transaxle: neutral position
(A/T models: “N” or “P”)
Steering wheel: neutral (center) position
1 TSB Revision

Page 38 of 738

MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine 36CONFIGURATION DIAGRAMS - Overall Configuration Diagram
OVERALL CONFIGURATION DIAGRAM
<HAT1
Roof wiring
CHBACK>Instrument panel
wiring harness

Page 39 of 738

MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine CONFIGURATION DIAGRAMS - How to Read Configuration Diagram37
,lHOW TO READ CONFIGURATION DIAGRAM
id<The wiring harness diagrams clearly show th

Page 42 of 738

$MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine CONFIGURATION DIAGRAMS - Engine Compartment <Turbo> A-69A-70 \ \ 36FOO14 A-35 A-36 A-37 A-38 A-39 A-40 A-41 A-42 A-43 A-44A-72 A-71A-67+ A-5 A-$

Page 43 of 738

$MITSUBISHI 3000GT 1995 2.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine CONFIGURATION DIAGRAMS - Engine CompartmentENGINE HOOD A-73 \ /I IIA-46 A-45 A-44 A-43A-42 A-56 A-57A-58 A-59 A-60 A-61A-62 A-63 A-64 A-65 En$

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 33-40 ... 40 next >

maintenance reset tire pressure reset boot radio antenna adblue reset ECU