1995 MITSUBISHI 3000GT drive

Downloaded from www.Manualslib.com manuals search engine 24GENERAL - Harness Connector Inspection
ess connector
contact pressure
checking harness
201 R057
Z16R1317
HARNESS CONNECTOR INSPECTION
CONNECTOR CONTINUITY AND VOLTAGE TESTWhen checking continuity and/or voltage at the waterproof
connectors, follow the steps below to avoid poor connector
contact and/or reduced waterproof performance of connectors.
(1) When checking is performed with the circuit in the stateof continuity, be sure to use the special tool (harness
connector).
Never insert a test bar from the harness side, because
to do so will reduce the waterproof performance and result
in corrosion.
(2) When the connector
JS disconnected for checking the fe-
male pin, the harness for checking the contact pressureof connector pins should be used.
Never force the insertion of a test bar, because to do
so will cause poor contact.(3) When the male pin is to be checked, apply the test bar
against the pin directly.
Care must be taken not to short-circuit the connector pins.
TERMINAL ENGAGEMENT CHECK
When the terminal stopper of connector is out of order, engage-
ment of male and female terminals becomes improper even
when the connector itself is engaged perfectly and the terminal
sometimes slips out to the rear side of connector. Ascertain,
therefore, that each terminal does not come off the connector
by pulling each harness wire.
CONNECTOR TERMINAL ENGAGEMENT AND
DISENGAGEMENTConnectors which are loose shall be rectified by removing
the female terminal from connector housing and raising its
lance to establish a more secure engagement. Removal of
connector terminal used for MFI and 4 A/l control circuit shallbe done in the following manner.
COMPUTER CONNECTOR(1) Insert screwdriver
[1.4 mm (.06 in.) width] as shown in
the figure, disengage front holder and remove it.
1 TSB Revision
IJ
I
I
I

Downloaded from www.Manualslib.com manuals search engine GENERAL - Harness Connector Inspection25 ~
Z16R1320
(2)Insert harness of terminal to be rectified deep into connec-tor from harness side and hold it there.
Housing lance/
’ Needle
’ Housing lance
Z16R132
(3)Insert tip of screwdriver [1.4 mm (.06 in.) width] into connec-tor in a manner as shown in the figure, raise housing
lance slightly with it and pull out harness.
CautionTool No. 753787-l supplied by AMP can be used
instead of screwdriver.(4)
insert needle through a hole provided on terminal and
raise contact point of male terminal.
ROUND WATERPROOF CONNECTOR
(1) Remove waterproof cap by using a screwdriver.
(2) Insert tip of screwdriver
[I.4 mm (.06 in.) or 2.0 mm (.08in.) width] into connector in a manner as shown in the
figure, raise housing lance slightly with it and pull out
harness.(3) Insert screwdriver through a hole provided on terminal
and raise contact point of male terminal.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 26GENERAL - Harness Connector Inspection
Front holder
\\Z16R1325]
Housing lance7,fiEL,
c
Terminal lance00000400\
RECTANGULAR WATERPROOF CONNECTOR
(1)Disengage front holder by using a screwdriver and remove
it.
(2) Inset-t tip of screwdriver [*0.8 mm (.03 in.) width] into con-
nector in a manner as shown in the figure, push it lightly
to raise housing lance and pull out harness.
*If right size screwdriver is not available, convert a conven-
tional driver to suit the size.
(3) Press contact point of male terminal down by holding a
screwdriver [1.4 mm (.06 in.) width] in a manner as shown
in the figure.
INJECTOR CONNECTOR
(1) Remove waterproof cap.
(2)Insert tip of screwdriver [1.4 mm (.06 in.) width] into connec-
tor in a manner as shown in the figure, press in terminal
lance and pull out harness.
(3) Press contact point of male terminal down by holding a
screwdriver [1.4 mm (.06 in.) width] in a manner as shown
in the figure.
CautionMake sure that lance is in proper condition before
terminal is inserted into connector.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CONFIGURATION DIAGRAMS - Dash Panel51
C-32c-33
A36F0179
00004255
C-25
C-26
C-27
C-28c-29
c-30
c-31
C-32c-33
Air conditioning control unit

Air conditioning control
unit*2

Air-inlet sensor
Air selection damper control motor
Body wiring harness (LH) and control wiring
harness combination
Body wiring harness (LH) and control wiring
harness combination
Body wiring harness (LH) and front wiring
harness combination
Body wiring harness (RH) and front wiring
harness combination
Body wiring harness (RH) and front wiring
harness combinationc-34
c-35
C-36c-37
C-38c-39c-40
c-41
C-42c-43
C-44c-45Body wiring harness (LH) and body wiring
harness (RH) combination
Foot light (RH)Body wiring harness (RH) and control wiring
harness combination
Auto-cruise control unit
Blower motor
Blower motor relay (HI)
Air conditioning compressor lock controllerAir-inlet sensor
*2
Air-therm0 sensor
Engine coolant temperature sensorMFI relay
Over drive and power
/ economy switch
TSB Revision1

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - ELCQ E\TT Circuit191
IGNIlSWIT(
2L-E-------_- ____.
L-F
jc-30)
(F)L-R
L-R
z(c-82)G-W,,6 ic-ss)
3
L-R
(L-R
TAILLIGHT RELAY
OVERDRIVE
SW1TCH(c-45)%lwT
(c-37)
ISE
HR07MOlAB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - ELC4 A/T Circuit195
OVERDRIVE AND~~';'~~;;ECONOMY
c
PARK/NEUTRALISE ~;~Cl;RON
I-A11
LIEI
AUTG-
CRUISE
CONTROLUNIT
'-y loIcc-37)A B C D E F
~~~~~~
R-W
(R-G
G-W
.ELECTRONIC CONTROLSUSPENSION.FOG LIGHT.GLOVE BOX LIGHT (F)G-W20 (F)G-W
VANITY MIRROR LiGHTAND INSPECTION()
LIGHT4.REAR WINDOW(G-W)~~~KJ;~BC$"' '-"-DEFOGGER.TURN-SIGNAL I.IGHTAND INSF
-
I
1 AND HAZARD LIGHTI
I
II1I
(c-14) $:--$:4
47
j$@ELECTOR
(c-45)ILLUMINATION
LIGHT
COMBINATION
METER(B-Y)
(D-03)
B-Y21
t' h
B-Y
8:F PWR11-
(R-G) G-YI"8 OVERDRIVE ANC(B-Y)#;gi;ECONOMY
34 (c-29):?
COMBINATION' '\ /\METER(B-Y)
(D-03)
R-Y
G-R
RHEOSTAT
HR07M02AB
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - ELC-4 A/T Circuit199
TAILLIGHT RELAY
l.r
OVERDRIVE AND~~~~~~ECONOMY
I
i
R-W
(
J/BMULTI-PURPOSEFUSED>JOVERDRIVE AND;t$~~&ECONOMYr----------_
NOTE:l:Hatcnback%2:Convertible
WITHOUT
K%isU,
PARK/NEUTRALI SE Pt&T~ON
I*
"80
G-W
G-w 80
G-WI\,Y
.ELECTRONIC CONTROL: -_____ ---_
SUSPENSIONMETER AND
.FOG LIGHT(F)G-WGAUGES14
.GLOVE BOX LIGHT,VANITY MIRROR(F)G-W
LIGHT AND20
INSRECTION LIGHTtt.REAR WINDOWGLOVE BOX LIGHT,DEFOGGER(G-W)VANITY MIRROR LIGHT
*TURN-SIGNAL LIGHTAND INSPECTION
AND HAZARD LIGHTl-L
T11 Ilr
(F)Y-R(Fj
(R-G
iI
)B--
L
3--.
G-
3
(c-14)
(R-G
COMBINATION
METER
(D-03)
I
%F
(
PW
1 1
-R-Y
37+-@f%wG-R B-YIRHEOSTAT
HR07M03AB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - ELC4 A/T Circuit
203 l
TAI
IL)r----
I/iWITHR-W
,------I \
WITHOUT
PARK/NEUTRAL/$$&$UISE $$$&~"I"" Kl~~I~ONI/1I-
(R-G
G-W
,FOG LIGHT,GLOVE BOX LIGHT,$!~;yA/j;RROR (F>G-WGAUGES
INSPECTION LIGHT(F>G-W20REAR WINDOWDEFOGGER+TURN-SIGNAL LIGHT(G-W) #&B~~R~&HL'~GHTAND HAZARD LIGHT
AND INSPECTION LIGHT(F>Y-R/t?\v.
IL
LI
(c-14)-\i
t(2
G-E
34
r
li---fE/JEWELECTOR
(c-45)ILLUMINATIONLIGHTI ,
G-'
t
8 OVERDRIVE ANC#@hECONOMkELC:4A/T(B-Y)
3q (C-29)12
dL-
(R-GCONTROL MODULE
COMBINATION
METER
(D-03)
PW
) /
-I ’
“I
LR-Y
G-R
\T
i
RiEOSTl
HR07M04AB
1 TSB Revision