1995 LAND ROVER DISCOVERY brake

MANIFOLD AND EXHAUST SYSTEM
7
REPAIR Refit
19.Ensure mating faces of inlet manifold and
cylinder head are clean.
20.Fit a new gasket, position inlet manifold to
cylinder head.
21.Fit nuts and bolts, tighten in the order shown to
the correct torque
25Nm
22.Position engine breather hose to manifold and
secure with bolts.
23.Connect fuel injector harness and intake air
temperature sensor multiplug.
24.Connect fuel hose to pressure regulator and
secure with clip.
25.Fit fuel pipe to fuel rail, tighten union to
10Nm
26.Connect vacuum hoses to manifold.
27.Position engine harness and cam cover brackets
to manifold, secure with bolts.
28.Connect breather hose and brake servo hose to
manifold, secure with clips.
29.Connect multiplug to fuel temperature sensor.
30.Connect breather hose to throttle housing and
secure with clip.
31.Connect throttle cable to cam and secure to
abutment bracket.
32.Connect coolant bypass hose to throttle housing.
33.Connect stepper motor and throttle
potentiometer multiplugs.
34.Connect air cleaner hose to throttle housing and
secure with clip.
35.Connect battery negative lead.
36.Adjust throttle cable.EXHAUST MANIFOLD GASKET - Mpi
Service repair no - 30.15.12
Remove
1.Raise vehicle.
2.Loosen 2 nuts securing downpipe to silencer
box.
3.Remove 4 nuts securing downpipe to exhaust
manifold.
4.Release downpipe from exhaust manifold.
5.Discard gasket.

MANIFOLD AND EXHAUST SYSTEM
9
REPAIR MANIFOLD CHAMBER GASKET - Mpi
Service repair no - 30.15.37
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Loosen union to relieve pressure.
Re-tighten union.
3.Release clip and remove air cleaner to throttle
housing hose.
4.Disconnect stepper motor and throttle
potentiometer multiplugs.
5.Release clip and disconnect breather hose from
throttle housing.
6.Release throttle cable from abutment bracket.
7.Release throttle cable from cam. Remove
coolant bypass hose from throttle housing.
8.Disconnect fuel temperature sensor multiplug.
9.Release clip and disconnect brake servo hose
from manifold.

30MANIFOLD AND EXHAUST SYSTEM
10
REPAIR 10.Release clip and disconnect breather hose from
manifold.
11.Release 2 bolts securing camshaft cover
brackets to manifold.
12.Disconnect 4 vacuum hoses from manifold.
13.Remove 6 bolts securing manifold chamber to
lower manifold.
14.Remove manifold chamber and collect gaskets.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
15.Ensure mating faces of manifold chamber and
lower manifold are clean.
16.Fit a new gasket, position manifold chamber to
lower manifold.
17.Fit bolts, tighten to the correct torque.
18.Connect vacuum hoses to manifold.
19.Position camshaft cover brackets to manifold,
secure with bolts.
20.Connect breather hose and brake servo hose to
manifold, secure with clips.
21.Connect multiplug to fuel temperature sensor.
22.Connect breather hose to throttle housing and
secure with clip.
23.Connect throttle cable to cam and secure to
abutment bracket.
24.Connect coolant bypass hose to throttle housing.
25.Connect stepper motor and throttle
potentiometer multiplugs.
26.Connect air cleaner hose to throttle housing and
secure with clip.
27.Reconnect battery negative lead.
28.Adjust throttle cable.

R380
1
REPAIR R380 MANUAL GEARBOX
Service repair no - 37.20.02
Remove
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
1.Install vehicle on a ramp [hoist].
2.Disconnect battery earth lead.
3.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
4.Remove sound insulation from top of
transmission tunnel.
5.Remove bolt and remove upper gear lever.
6.Remove screws securing gear selector lever and
high/low selector lever draft excluders.
7.Remove draft excluder clamp rings.
8.Remove handbrake cable clevis pin clip and
clevis pin.
9.Remove 'C' clip and cable adjuster.
10.Select low range to prevent gear lever fouling
tunnel when removing gearbox.
11.Remove bolt securing gearbox breather pipe clip
to cylinder block.
12.Remove bolts securing fan cowl to radiator.
13.Release fan cowl from radiator and lay over fan
blades.
14.Raise ramp [hoist].
15.Drain oil from main gearbox and transfer
gearbox.
See SECTION 10, Maintenance,
Under Vehicle Maintenance
16.Remove exhaust front pipe(s).See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
System Complete
17.Release intermediate exhaust pipe(s) from
mountings and tie aside.
18.Remove bolts securing clutch slave cylinder.
19.Release slave cylinder from clutch housing and
collect spacer.
20.Mark propeller shaft drive flange relationships for
reassembly.
21.Disconnect front and rear propeller shafts from
transfer gearbox. Tie shafts aside.
22.Remove clamp and disconnect speedometer
cable from transfer gearbox.
23.Release handbrake cable from transmission
tunnel.
24.Temporarily support transmission in a way which
enables the crossmember to be removed and a
hoist cradle to be fitted.

R380
3
REPAIR Assembling transfer gearbox to main gearbox
45.Clean extension housing and transfer gearbox
mating faces.
46.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
47.Fit and tighten nut and bolts to
34Nm.
48.Connect high/low operating rod, fit and tighten
locknut.
49.Fit link to differential lock lever and secure with 2
clips
50.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2Nm.
51.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15Nm.
Fitting transfer gearbox and main gearbox
assembly to engine
52.Position transmission assembly to hoist cradle.
53.Clean bell housing and engine mating faces.
54.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft.
55.Position and raise hoist, and fit transmission to
engine whilst keeping wires and pipes clear to
prevent trapping.
56.Fit and tighten nuts securing transmission to
engine.
57.Connect reverse lamp switch connectors and
differential lock switch connectors.
58.Secure breather pipes to harness with clips.
59.Position temporary support.
60.Remove 2 bolts securing lifting cradle to
transmission and remove hoist. Apply Loctite
290 to bolts and refit bolts.
61.Position cross-member, loosely fit nuts and bolts
securing cross-member mountings to
transmission.62.Raise transmission, align cross-member and
loosely fit nuts and bolts securing cross-member
to chassis.
63.Tighten all securing nuts and bolts. Remove
supporting jack from under sump.
64.Remove temporary support.
65.Fit handbrake cable through transmission tunnel
and secure gaiter.
66.Connect speedometer cable to transfer gearbox.
67.Line up marks and connect front and rear
propeller shafts.
68.Clean spacer, clutch slave cylinder and gearbox
mating faces.
69.Position spacer and slave cylinder, fit bolts.
Tighten to
25Nm.
70.Untie intermediate exhaust pipe(s) and refit
exhaust front pipe(s).
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust System
Complete
71.Refill main gearbox and transfer gearbox with oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
72.Lower ramp [hoist].
73.Fit fan cowl, fit and tighten bolts.
74.Align breather pipe clip to cylinder block, fit and
tighten bolts.
75.Fit handbrake cable adjuster and secure with 'C'
clip.
76.Align cable trunnion to handbrake lever, fit clevis
pin and secure with clip.
77.Check handbrake adjustment.
See SECTION
10, Maintenance, Vehicle Interior
78.Fit upper gear lever, fit and tighten bolt.
79.Fit gear selector lever and high/low selector
lever draft excluders.
80.Position draft excluder clamp rings, fit and
tighten screws.
81.Refit sound insulation.
82.Refit centre console.
See CHASSIS AND
BODY, Repair, Centre Console
83.Connect battery earth lead.

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.

TRANSFER GEARBOX
3
REPAIR Refit
36.Select 'P' in main gearbox, with low range and
differential lock selected in transfer gearbox.
37.Secure transfer gearbox to adaptor plate on
lifting hoist.
38.Ensure joint faces of transfer and main
gearboxes are clean and guide studs 18G 1425
are fitted.
39.Raise hoist until transfer gearbox can be located
over guide studs to main gearbox. At the same
time locate high/low lower link to yoke.
40.Remove guide studs and secure transfer
gearbox to main gearbox.41.Complete refitting by reversing removal
procedure, noting the following important points.
42.After removal of adaptor plate from transfer
gearbox, clean threads of four bottom cover
bolts, coat threads with Loctite 290 and fit
together with spring washers. Tighten to
25Nm
43.Add correct grade of oil to transfer gearbox to oil
level plug hole.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
44.Check main gearbox oil level.
45.Check operation of parking brake and adjust as
necessary.
See SECTION 10, Maintenance,
Vehicle Interior

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
LT230T Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................
Shiftlock
Shiftlock screws 9..........................................................................................
Neutral switch 25............................................................................................