1995 LAND ROVER DISCOVERY ECU

ZF
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Coupling shaft to mainshaft 42*......................................................................
Filler tube to sump 68.....................................................................................
Gear change lever to gearbox 25...................................................................
Cooler pipe adaptor to gearbox 42.................................................................
Securing screws - clutch F 10.........................................................................
Securing screw - parking pawl 10...................................................................
Securing screws - pump 10............................................................................
Intermediate plate plugs (M20) 50..................................................................
Intermediate plate plugs (M14) 40..................................................................
Bell housing mounting bolts 46.......................................................................
Governor mounting screws 10........................................................................
Extension housing bolts 23.............................................................................
Control unit mounting bolts 8.........................................................................
Sump plug 10..................................................................................................
Mounting screws for sump 8..........................................................................
Drive plate to converter 39*.............................................................................
Gearbox to engine 42.....................................................................................
Strut (threaded end) 42...................................................................................
Bottom cover to converter housing 9.............................................................
Cover - converter housing 9...........................................................................
Drive plates to crankshaft adaptor 40*............................................................
Adaptor to crankshaft 84.................................................................................
NOTE: * These bolts must have threads coated with Loctite 270 prior to assembly.
Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................

ZF
1
SERVICE TOOLS AUTOMATIC GEARBOX HOLDING FIXTURE
NOTE: This fixture enables ZF gearbox to be held securely during bench sited repairs. It can be
manufactured to details given, or purchased under service tool number LST 118.

47PROPELLER SHAFTS
4
REPAIR REAR PROPELLER SHAFT
Service repair no - 47.15.03
NOTE: SGF rubber coupling should be left
attached to propeller shaft. Only remove
coupling from propeller shaft if
replacement is required.
Remove
1.Scribe alignment marks on flanges at both ends
of propeller shaft to ensure correct refitting.
2.Remove three nuts and bolts securing flexible
coupling to axle flange.
3.Remove nuts securing propeller shaft flange to
transfer gearbox.
4.Raise propeller shaft at gearbox end detach
coupling from spigot at differential and withdraw
shaft.
NOTE: For replacement of spigot (pinion
flange centralising peg).
See REAR AXLE
AND FINAL DRIVE, Overhaul, Axle
Differential Assembly
Overhaul
Service repair no - 47.15.12
NOTE: Refer to front propeller shaft
overhaul procedure for gearbox end of
shaft. The SGF rubber coupling is a
non-serviceable item.
Refit
5.Locate flexible coupling over spigot, align
scribed marks and secure at transfer gearbox.
Tighten to
47 Nm.
6.Secure flexible coupling to axle flange with three
nuts and bolts and Tighten to
78 Nm.
FLEXIBLE COUPLING
NOTE: Flexible coupling should only be
removed if a new coupling is to be fitted.
Remove
1.Remove rear propeller shaft.
See Rear
Propeller Shaft.
2.Remove nuts and bolts securing flexible
coupling to propeller shaft.
Refit
3.Reverse removal procedure. Fit nuts and bolts.
Tighten to
78 Nm.

REAR AXLE AND FINAL DRIVE
3
REPAIR REAR HUB ASSEMBLY
Service repair no - 64.15.01
Remove
1.Place rear axle onto axle stands and remove
road wheel.
2.Release brake hose clips and remove brake
caliper bolts. Secure to one side.
WARNING: Take care not to kink brake
hose.
3.Remove five bolts and withdraw axle shaft.
4.Remove joint washer.
5.Bend back lock washer tabs.
6.Remove locknut and lock washer.
7.Remove hub adjusting nut.
8.Remove spacing washer.
9.Remove hub and brake disc assembly complete
with bearings.REAR HUB COMPONENTS
1. Sensor ring retaining nut ABS.
2. Axle shaft.
3. Axle shaft joint washer.
4. Axle shaft retaining bolt (five off).
5. Lock nut.
6. Lock washer.
7. Hub adjusting nut.
8. Spacing washer.
9. Outer bearing.
10. Hub.
11. Inner bearing.
12. Grease seal.
13. Brake disc.
14. Disc retaining bolt (five off).
15. Sensor ring ABS.

51REAR AXLE AND FINAL DRIVE
4
REPAIR Refit
10.Clean stub axle. Retract ABS sensor slightly
from sensor sleeve, if applicable
11.Fit hub assembly to stub axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
14.Fit a new lock washer.
15.Fit locknut. Tighten to61 Nm.
16.Tab over lock washer to secure adjusting nut
and locknut.
17.Using a new joint washer fit axle shaft to hub,
secure with five bolts. Tighten to
65 Nm.
18.Fit brake caliper. Tighten to82 Nm.
Secure brake pipes to axle casing.
19.If applicable, set ABS brakes sensor.
Push sensor in until it touches sensor ring then
rotate hub to set sensor.
20.Fit road wheel, remove axle stands and final
tighten road wheel nuts to
126 Nm.
21.Operate footbrake to locate brake pads before
driving vehicle.

REAR AXLE AND FINAL DRIVE
1
OVERHAUL AXLE DIFFERENTIAL ASSEMBLY
Service repair no - 51.15.07.
DISMANTLE
NOTE: Mark differential components so
their original positions relative to other
components is maintained. Bearing caps
must not be interchanged.
1.Remove axle shafts then differential assembly
fom axle.
2.Remove roll pin securing bearing nut locking
fingers to bearing caps. Remove locking fingers.
3.Loosen bearing cap bolts and mark caps for
assembly.
4.Using service tool LRT-54-508, remove bearing
adjusting nuts.
5.Remove bearing cap bolts and bearing caps.
6.Remove crown wheel differential unit and
bearings.
Remove pinion FRONT AXLE DIFFERENTIAL
ONLY
7.Remove pinion flange nut using service tool
LRT-51-003 to restrain flange.
8.Remove washer and pinion drive flange.
9.Remove pinion complete with bearing and outer
bearing shims.
10.Remove pinion flange oil seal, spacer and
bearing.
Remove pinion REAR AXLE DIFFERENTIAL ONLY
7.Remove pinion flange centralizing peg using
service tool LRT-51-008.
8.Remove pinion flange nut using service tool
LRT-51-003 to restrain flange.
9.Remove pinion complete with bearing and outer
bearing shims.
10.Remove pinion flange oil seal and bearing.
11.Using service tool LRT-54-505, remove pinion
head bearing track and shim and drive out outer
bearing of differential housing.

51REAR AXLE AND FINAL DRIVE
2
OVERHAUL
12.Remove pinion head bearing with service tool
LRT-99-002.
13.Remove bolts and washers securing crown
wheel to differential flange. Remove crown
wheel.
14.Remove differential carrier bearings.
15.Remove circlips and extract differential cross
shaft.
16.Withdraw differential gears and pinions.
17.Clean all components.
INSPECTION
18.Check all bearings for wear and pitting.
19.Check all gears for wear, scuffing, pitting and
damaged teeth.
20.Supplied as matched sets are: crown wheel and
pinion, pinion housing and bearing caps.
ASSEMBLE
Differential gears
21.Fit differential gears to differential housing.
22.Fit differential cross shaft and circlips.

REAR AXLE AND FINAL DRIVE
7
OVERHAUL PINION PRELOAD SHIMS
PART No. INCH MM
FTC3869 .085 2.155
FTC3870 .084 2.130
FTC3871 .083 2.105
FTC3872 .082 2.080
FTC3873 .081 2.055
FTC3874 .080 2.030
FTC3875 .079 2.005
FTC3876 .078 1.980
FTC3877 .077 1.955
FTC3878 .076 1.930
FTC3879 .075 1.905
FTC3880 .074 1.880
FTC3881 .073 1.855
FTC3882 .072 1.830
FTC3883 .071 1.805
FTC3884 .070 1.780
FTC3885 .069 1.755
FTC3886 .068 1.730
FTC3887 .067 1.705
FTC3888 .066 1.680
FTC3889 .065 1.655
FTC3890 .064 1.630
FTC3891 .063 1.605
FTC3892 .062 1.580
FTC3893 .061 1.555
FTC3894 .060 1.530
FTC3895 .059 1.505
FTC3896 .058 1.480
Fitting Pinion Oil Seal
59.Coat outer diameter of seal with grease. Fit seal
lip side leading flush with end face of housing
using tool LRT-51-001.
Fit pinion drive flange - front axle differential
60.Lubricate seal lips with axle oil.
61.Fit spacer and pinion drive flange to differential.
62.Secure flange with washer and nylon nut.
Tighten to
130 Nm.
Fit pinion drive flange - rear axle differential
60.Lubricate seal lips with axle oil.
61.Fit pinion drive flange to differential and secure
with washer and nylon nut. Tighten to
130 Nm.
62.Coat centralizing peg with Loctite 601 or 638 and
fit over pinion retaining nut in drive flange.