1995 LAND ROVER DISCOVERY sway bar

60FRONT SUSPENSION
6
REPAIR ANTI-ROLL[SWAY] BAR BALL JOINT LINKS
Service repair no - 60.10.04.
Remove
1.Remove two nuts, bolts, washers and rubber
bushes from ball joint links.
2.Remove cotter pin and loosen castellated nut a
few turns.
3.Release ball joint using special tool 18G 1063A
as shown.
4.Remove castellated nut and ball joint link.
Refit
5.Fit ball joint link and castellated nut. Ensure ball
joint link arm points up. Tighten to
40Nmand fit
new cotter pin.
6.Align anti-roll bar to ball joint links.
7.Fit bolts, washers and rubber bushes using new
self locking nuts secure anti-roll[sway] bar to ball
joint links. Tighten to
68Nm.

FRONT SUSPENSION
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Anti-roll[sway] bar front
- Strap nyloc nuts 30..............................................................................
- Ball link self lock nut 68........................................................................
- Castellated nut 40................................................................................
Drag link to axle 40.........................................................................................
Securing ring for mounting turret 14...............................................................
Radius arm to chassis 176...............................................................................
Panhard rod mounting arm to chassis 88.......................................................
Panhard rod to axle 88....................................................................................
Panhard rod to mounting bracket 88...............................................................
Tie bar to Panhard rod 110..............................................................................
Radius arm to axle (front only) 197..................................................................
Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6...........................................................................
M6 9...........................................................................
M8 25...........................................................................
M10 45.........................................................................
M12 90.........................................................................
M14 105.........................................................................
M16 180.........................................................................
UNC / UNF
1/4 9...........................................................................
5/16 24.........................................................................
3/8 39...........................................................................
7/16 78.........................................................................
1/2 90...........................................................................
5/8 136...........................................................................

64REAR SUSPENSION
4
REPAIR ANTI-ROLL[SWAY] BAR ASSEMBLY REAR
Service repair no - 64.35.08.
KEY
1. Anti-roll[sway] bar
2. Rubber bush
3. Strap
4. Nut, bolt, washer5. Nut and washer
6. Ball joint link arm
7. Bolt and washer
8. Castellated nut and cotter pin
Remove
1.Note for reassembly, position of rubber bushes
on anti-roll bar.
2.Remove four nuts, bolts and washers securing
two bush straps.
3.Remove nuts, bolts, washers and rubber bushes
from the ball joint links and remove anti-roll bar.Refit
4.Position rubber bushes on anti-roll bar. Fit joint
towards axle.
5.Fit anti-roll bar with two straps. Ensure ball joint
link arms point down as shown. Loosely fit, bolts,
washers and new nyloc nuts.
6.Fit bolt, washers and rubber bushes. Fit anti-roll
bar to ball joint links. Tighten to
68Nm.
7.Tighten nuts securing straps to30Nm.

REAR SUSPENSION
5
REPAIR ANTI-ROLL[SWAY] BAR BALL JOINT LINKS
Service repair no - 64.35.24.
Remove
1.Remove two nuts, bolts, washers and rubber
bushes from ball joint links and lower anti-roll bar
to clear links.
2.Remove cotter pin and loosen castellated nut a
few turns.
3.Release ball joint using special tool 18G 1063A
as shown.
4.Remove castellated nut and ball joint link.
Refit
5.Fit ball joint link arm and castellated nut. Point
ball joint link arm down as shown. Tighten to
40Nmand fit new cotter pin.
6.Align anti-roll bar to ball joint links.
7.Fit bolts, washers and rubber bushes using new
self locking nuts secure anti-roll bar to ball joint
links. Tighten to
68Nm.

REAR SUSPENSION
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Anti-roll[sway] bar rear
- Strap nyloc nuts 30..............................................................................
- Ball link self lock nut 68........................................................................
- Castellated nut 40................................................................................
Top link to mounting bracket 176.....................................................................
Bottom link to axle 176.....................................................................................
Bottom link to chassis 176...............................................................................
Top link bracket to rear cross member 47......................................................
Shock absorber to axle 37..............................................................................
Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................