1995 LAND ROVER DISCOVERY service

SFI
23
REPAIR ADD: 09/95
20.Remove nut and bolt securing RH side of upper
fuel tank strap to chassis.
21.Remove 4 nuts and bolts securing fuel tank
cradle.
22.Remove fuel tank cradle.
23.With assistance, tilt right hand side of tank
upwards and manoeuvre through chassis to
remove.
Do not carry out further dismantling if
component is removed for access only.
24.Release vent hose from tank pressure sensor.
25.Remove vent hose from 3 fuel tank clips.
26.Using service tool LRT-19-009 loosen and
remove the metal locking ring.
27.Prise the pump from the tank opening using a
blunt instrument under the edge of the lip of the
pump flange.
CAUTION: Do not lift the pump from the
tank using the feed and return stubs.
28.Remove and discard seal.

19FUEL SYSTEM
24
REPAIRADD: 09/95 Refit
29.Fit NEW pump seal to tank opening.
30.Carefully lower pump into tank opening, pressing
firmly on the pump top flange to allow correct
positioning.
NOTE: Ensure location tag on pump top
flange is engaged correctly to tank
opening lip.
31.Fit locking ring and tighten to
35 Nmusing
service tool LRT-19-009.
32.Fit vent hose to fuel tank clips and connect to
pressure sensor.
33.With assistance, fit fuel tank into position.
34.Fit fuel tank cradle and secure with nuts and
bolts.
35.Align upper fuel tank strap and secure with nut
and bolt.
36.Fit NEW clip to fuel filler neck hose.
37.Connect fuel filler neck internal breather to tank.
38.Connect fuel filler neck hose to tank.
39.Position fuel filler neck hose clip and tighten until
head shears.
40.Connect vent line quickfit connector to
liquid/vapour separator.
41.Connect vent line hose connection.
42.Position anti-roll [sway] bar straps and secure
with nuts and bolts.
43.Remove stand(s) and lower vehicle.
44.Connect both fuel lines to the pump by pushing
the connectors down each line square to the
pump connection until the connectors positively
latches.
45.Connect multiplugs to fuel pump and pressure
sensor.
46.Reconnect battery negative lead.
47.Refill tank with drained fuel.
48.Run the engine to check for any fuel leaks.
49.Fit access panel and secure with screws.
50.Reposition loadspace sound insulation and
carpet.
51.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair, rear
compartment trim panels
52.Fit tail door tread strip and secure with screws.FUEL TANK - DRAINING - ADVANCED EVAPS
Service repair no - 19.55.02
WARNING: Before removing the fuel tank
it must be drained.
WARNING: Petrol/gasoline vapour is
highly flammable and in confined spaces
is also explosive and toxic. Always have a
fire extinguisher containing FOAM, CO2, GAS or
POWDER close at hand when handling or draining
fuel. See Introduction
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
NOTE: Assuming the fuel tank is FULL
drain the following quantities:
Renew Fuel pump = 9 Litres (2.4 US Gallons)
Renew Fuel filler neck = 22 Litres (6 US Gallons)
Renew Fuel tank = COMPLETE DRAIN
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Remove 6 screws securing tail door tread strip
and remove tread strip.
4.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair,

19FUEL SYSTEM
26
REPAIRADD: 09/95 FUEL FILLER NECK - ADVANCED EVAPS
Service repair no - 19.55.07
WARNING: Ensure that fuel handling
precautions given in 1 - Introduction are
strictly adhered to when carrying out
following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Check the amount of fuel in the tank. If the tank
is full drain 6 US gallons (22 litres) minimum.
See fuel tank - draining.
4.Remove 6 screws securing tail door tread strip
and remove tread strip.
5.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair, rear
compartment trim panels
6.Fold back loadspace carpet and sound
insulation to gain access to RH mudflap fixing.
7.Raise rear of vehicle.
WARNING: Support on safety stands.
8.Remove nut and bolt securing filler neck support
bracket to mud flap bracket.
NOTE: This fixing also retains the filler
neck earth strap.
9.Remove 5 nuts and bolts securing mud flap to
body.
10.Remove mud flap.

19FUEL SYSTEM
28
REPAIRADD: 09/95 Refit
26.Fit vent line to filler neck.
27.Fit NEW clip to filler neck hose.
28.Fit hose to filler neck.
29.Position filler neck hose clip and tighten until
head shears.
30.Fit filler neck assembly to vehicle.
NOTE: To aid fitment of filler neck through
body grommet apply a soap solution to lip
of grommet.
31.Fit NEW clip to fuel filler neck hose.
32.Connect fuel filler neck internal breather to tank.
33.Connect fuel filler neck hose to tank.
34.Position fuel filler neck hose clip and tighten until
head shears.
35.Connect vent line quickfit connector to
liquid/vapour separator.
36.Connect the pressure sensor breather pipe
connection.
37.Connect the vent line hose connection.
38.Fit mud flap and secure with nuts and bolts.
39.Position filler neck support bracket and earth
strap to mud flap bracket and secure with nut
and bolt.
40.Remove stand(s) and lower vehicle.
41.Reposition loadspace sound insulation and
carpet.
42.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair,
43.Fit tail door tread strip and secure with screws.
44.Refill tank with drained fuel.
45.Fit fuel filler cap to filler neck.
46.Close filler flap, lock with ignition key and
remove key.
47.Reconnect battery negative lead.FUEL TANK FILLER CAP - ADVANCED EVAPS
Service repair no - 19.55.08
Remove
1.Fit ignition key to fuel filler flap lock and open
flap.
2.Remove screw securing cap retaining strap to
body.
3.Remove fuel filler cap.
Refit
4.Fit fuel filler cap.
5.Position cap retaining strap to body and secure
with screw.
6.Close filler flap, lock with ignition key and
remove key.

SFI
29
REPAIR ADD: 09/95 ANTI-TRICKLE FILL VALVE - ADVANCED EVAPS
Service repair no - 19.55.31
Remove
1.Remove the fuel filler neck.
See fuel filler neck
- advanced evaps
2.Release the cobra clip securing the hose to the
liquid/vapour separator and disconnect the hose.
3.Loosen the grub screw on the valve nut, two
complete turns.
4.Loosen the valve nut completely.
NOTE: The nut is held captive by the stub
pipe on the filler neck.
5.Carefully remove the valve and hose assembly
from the filler neckRefit
6.Fit a new 'O' ring to the recess in the stub pipe.
7.Fit the valve and hose assembly to the filler neck
stub pipe, ensuring that the 'O' ring is fitted
around the body of the valve as it is pushed into
the filler neck stub pipe.
8.Hand tighten the nut, then tighten to
3 Nm.
9.Tighten the grub screw to2 Nm.
10.Connect the hose to the liquid/vapour separator
and secure with the cobra clip.
11.Fit the fuel filler neck.
See fuel filler neck -
advanced evaps;refit

Mpi
1
DESCRIPTION AND OPERATION DESCRIPTION
The Mpi Modular Engine Management System
(MEMS) controls the fuel injection and programmed
ignition systems.
The main features are as follows:
·The Engine Control Module (ECM) controls
programmed ignition and fuel injection. The ECM
incorporates short circuit protection and can
store intermittent faults on certain inputs.
Testbook can interrogate the ECM for these
stored faults.
·The ECM uses the speed/density method of air
flow measurement to calculate fuel delivery. This
method measures the inlet air temperature and
inlet manifold pressure and assumes that the
engine is a calibrated vacuum pump with its
characteristics stored in the ECM
·If certain system inputs fail, the ECM implements
a back-up facility to enable the system to
continue functioning, although at a reduced level
of performance.
·A separate diagnostic connector allows engine
tuning or fault diagnosis to be carried out using
Testbook without disconnecting the ECM
harness connector.
·The ECM harness multiplug incorporates
specially plated pins to minimise oxidation and
give improved reliability.
·The throttle potentiometer requires no
adjustment in service. The following components
supply data for both fuelling and ignition:Ignition system
The ECM determines the optimum ignition timing
based on the signals it receives from the following
sensors:
1.Crankshaft sensor - Engine speed and
crankshaft position.
2.Manifold absolute pressure sensor - Engine load
3.Coolant temperature sensor - Engine
temperature.
4.Manifold absolute pressure sensor - Throttle
closed.
5.Knock sensor - Engine noise and vibration.
MEMS uses no centrifugal or vacuum advance, timing
being controlled by the ECM which is energised by the
main relay, within the relay module. Spark distribution
is achieved by 2 coils mounted at the rear of the
engine and controlled by the ECM.

Mpi
1
REPAIR KNOCK SENSOR
Service repair no - 18.30.18
Remove
1.Disconnect multiplug from knock sensor.
2.Remove knock sensor.
Refit
3.Clean mating face of cylinder block.
4.Fit knock sensor. Tighten to
15 Nm
5.Connect multiplug.IGNITION COILS
Service repair no - 18.20.40 - 1 & 4 Cylinders
Service repair no - 18.20.41 - 2 & 3 Cylinders
Remove
1.Disconnect battery negative lead.
2.Disconnect 4 h.t. leads from coils.
NOTE: Mark the position of the h.t. leads
to ensure correct refitment.
3.Disconnect 2 multiplugs from coils.
4.Disconnect crankshaft sensor multiplug.
5.Remove screw securing crankshaft sensor
multiplug to coil bracket.
6.Remove 3 bolts securing coil bracket to bell
housing.
NOTE: Access to the rear bolts is from
under the vehicle.
7.Remove coil assembly.
Refit
8.Position coil assembly to bell housing.
9.Fit 3 bolts and tighten to the correct torque.
10.Secure crankshaft sensor multiplug to coil
bracket with screw.
11.Connect crankshaft sensor multiplug.
12.Connect multiplugs and h.t. leads to coils.
13.Reconnect battery negative lead.

19FUEL SYSTEM
2
REPAIR COOLANT TEMPERATURE SENSOR
Service repair no - 18.30.10
Remove
1.Position drain tin below coolant pump hose.
2.Disconnect sensor multiplug.
3.Release harness clip and harness.
4.Remove sensor.
Refit
5.Clean sensor.
6.Fit sensor and tighten to the correct torque.
7.Position harness and secure with clip.
8.Connect multiplug.
9.Top-up cooling system.CRANKSHAFT SENSOR
Service repair no - 18.30.12
Remove
1.Position vehicle on ramp [hoist].
2.Disconnect multiplug from crankshaft sensor
flylead.
3.Remove screw, release lead from bracket.
4.Raise ramp [hoist].
5.Remove 2 bolts securing crankshaft sensor.
6.Remove crankshaft sensor.
Refit
7.Clean crankshaft sensor and mating surface of
backplate.
8.Fit crankshaft sensor, fit bolts. Tighten to
7Nm
9.Lower vehicle.
10.Position lead to bracket, fit and tighten screw.
11.Connect multiplug