1995 LAND ROVER DISCOVERY fuel

SFI
3
REPAIR FUEL SYSTEM - DEPRESSURISE
WARNING: Fuel pressure of up to 2.5 bar
will be present in the system, even if the
engine has not been run for some time.
Always depressurise the system before
disconnecting any components in the fuel feed
line (between fuel pump and pressure regulator).
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
NOTE: Fuel pressure can be relieved at
fuel rail feed union or fuel filter unions.
1.Position cloth around relevant union to protect
against fuel spray.
2.Carefully slacken union.
3.Tighten union to correct torque once pressure
has relieved.

19FUEL SYSTEM
4
REPAIR ENGINE CONTROL MODULE (ECM)
Service repair no - 18.30.01
Remove
1.Disconnect battery negative lead.
2.Release and move washer reservoir aside.See
WIPERS AND WASHERS, Repair, Washer
Reservoir
3.Remove 2 studs securing ECM cover.
4.Remove cover.
5.Disconnect 3 ECM multiplugs.
6.Remove 2 bolts securing ECM.
7.Release ECM from 2 lower retainers.
8.Remove ECM.
Refit
9.Reverse removal procedure.
NOTE: Ensure ECM is correctly located by
lower retainers.MASS AIR FLOW SENSOR (MAF SENSOR)
Service repair no - 19.22.25
Remove
1.Disconnect battery negative lead.
2.Loosen clip and disconnect intake hose from
MAF sensor.
3.Disconnect multiplug from MAF sensor.
4.Release 2 clips and remove MAF sensor from air
cleaner.
5.Collect 'O' ring seal.
Refit
6.Ensure mating faces of air cleaner, MAF sensor
and intake hose are clean.
7.Fit 'O' ring to MAF sensor.
8.Fit MAF sensor to air cleaner and secure with
clips.
9.Connect multiplug to MAF sensor.
10.Connect intake hose and secure with clip.
CAUTION: Failure to connect intake hose
securely will allow unmetered air to enter
the engine, causing running problems.
11.Reconnect battery negative lead.

SFI
5
REPAIR FUEL RAIL AND INJECTORS
Service repair no - 19.60.04 - Fuel Rail
Service repair no - 19.60.12 - Injectors
Remove
1.Disconnect battery negative lead.
2.Depressurise fuel system.
See Fuel System -
Depressurise
3.Release plenum chamber and place aside.See
Plenum Chamber
4.Disconnect purge hose, crankcase breather
hose, servo vacuum hose and fuel regulator
hose from ram housing.
5.Remove 6 bolts securing ram housing to inlet
manifold.6.Place small packing block on inlet manifold.
Lever between packing block and ram pipe
housing to break seal.
CAUTION: Do not lever against fuel rail.
7.Remove ram housing.
8.Place cloth over inlet manifold to prevent ingress
of foreign matter.
9.Disconnect 8 injector multiplugs.
10.Disconnect fuel temperature sensor multiplug.
11.Position cloth around fuel feed pipe union to
absorb fuel spillage.
12.Disconnect fuel feed pipe from fuel rail.
13.Plug fuel pipe and rail.
14.Slacken clip securing fuel return hose.

19FUEL SYSTEM
6
REPAIR 15.Disconnect hose, plug return hose and rail.
Remove cloth.
16.Remove 6 nuts securing fuel rail and ignition coil
bracket to inlet manifold.
17.Release ignition coil bracket from inlet manifold
studs. Place aside.
18.Release fuel rail and injectors from inlet
manifold.
Do not carry out further dismantling if component
is removed for access only.
19.Remove fuel rail and injectors.
20.Remove 2 bolts securing fuel pressure regulator
to fuel rail.
21.Remove pressure regulator assembly.
22.Remove 'O' ring from fuel pressure regulator and
discard.
23.Remove 8 clips securing injectors to fuel rail.
24.Remove injectors from fuel rail.
25.Remove 2 'O' rings from each injector and
discard.Refit
26.Ensure mating surfaces between inlet manifold
and ram pipe housing are clean.
27.Ensure all locations in fuel rail and inlet manifold
are clean.
28.Lubricate and fit new 'O' rings to injectors and
fuel pressure regulator.
29.Fit fuel pressure regulator to fuel rail. Secure
with bolts. Tighten to
10 Nm.
30.Fit injectors to fuel rail. Secure with clips.
31.Position fuel rail to inlet manifold. Engage
injectors, one bank at a time.
32.Position ignition coil bracket on inlet manifold
studs.
33.Secure ignition coil bracket and fuel rail to inlet
manifold with nuts. Tighten to
8 Nm.
34.Remove plugs from fuel feed and return pipes
and rail.
35.Connect hose and tighten clip.
36.Clean feed pipe union and connect fuel feed
pipe to fuel rail. Tighten union to
16 Nm.
37.Connect multiplugs to fuel injectors and fuel
temperature sensor.
38.Remove cloth from inlet manifold.
39.Apply a thin, uniform coating of Loctite 577
sealant to mating face of inlet manifold.
40.Fit ram housing to inlet manifold. Secure with
bolts. Tighten to
24 Nm.
41.Connect purge hose, crankcase breather hose,
servo and pressure regulator vacuum hoses to
ram housing.
42.Fit plenum chamber.
See Plenum Chamber
43.Reconnect battery negative lead.
44.Start engine. Check for leaks around fuel rail and
injectors.

SFI
7
REPAIR FUEL TEMPERATURE SENSOR
Service repair no - 19.22.08
Remove
NOTE: Because fuel leakage will not occur
when sensor is removed, it is not
necessary to depressurise the fuel system
for this operation.
1.Disconnect battery negative lead.
2.Disconnect multiplug from fuel temperature
sensor.
3.Remove sensor from fuel rail.
Refit
4.Ensure sensor and location in fuel rail are clean.
5.Fit sensor. Tighten to
17 Nm.
6.Connect multiplug.
7.Reconnect battery negative lead.

19FUEL SYSTEM
8
REPAIR IGNITION COILS
Service repair no - 18.20.45 - Set
Service repair no - 18.20.43 - Each
Service repair no - 18.20.44 - Extra - Each
Remove
1.Disconnect battery negative lead.
2.Disconnect H.T. leads from ignition coils. Note
positions of leads.
3.Place H.T. leads aside.
4.Disconnect ignition coil multiplug.
5.Remove 4 nuts securing coil bracket.
6.Release ignition coil bracket from inlet manifold
studs.
7.Manoeuvre coil/bracket assembly from behind
plenum chamber and remove.
8.Remove terminal cover. Note lead positions.
9.Remove 2 nuts securing leads to coil terminals.
10.Remove leads from terminals.
11.Remove 3 Torx screws securing ignition coil to
bracket and remove coil.Refit
12.Fit ignition coil to bracket. Secure with screws.
13.Connect leads to terminals. Secure with nuts.
14.Fit terminal cover.
15.Position ignition coil bracket on inlet manifold
studs.
16.Secure fuel rail and ignition coil bracket with
nuts. Tighten to
8 Nm.
17.Connect multiplug.
18.Connect H.T. leads to respective coil towers.
19.Reconnect battery negative lead.

19FUEL SYSTEM
10
REPAIR KNOCK SENSOR
Service repair no - 18.30.28 - Sensor - LH
Service repair no - 18.30.30 - Sensor - RH
CAUTION: Due to the sensitivity of the
sensors, do not apply tape or sealant to
sensor threads.
Remove
1.Raise vehicle on ramp.
2. RH Sensor only:Remove bolt securing starter
motor heatshield to RH engine mounting.
3.Release heatshield clip from starter solenoid.
4.Move heatshield aside for access to knock
sensor.
5. Both sensors:
Disconnect sensor multiplug.
6.Remove sensor.
Refit
7.Clean sensor and mating face.
8.Fit sensor. Tighten to
16 Nm.
9.Connect sensor multiplug.
10. RH Sensor only:Manoeuvre heatshield into
position.
11.Secure clip to solenoid.
12.Align bracket to mounting and fit bolt. Fit and
tighten bolt.
13.Lower ramp.
CAUTION: Failure to tighten sensor to
correct torque will result in malfunction or
sensor damage.

SFI
11
REPAIR FUEL PRESSURE REGULATOR
Service repair no - 19.45.06
Remove
1.Disconnect battery negative lead.
2.Depressurise fuel system.
See Fuel System -
Depressurise
3.Position cloth over fuel feed union, slacken union
to release fuel pressure, then re-tighten union.
4.Release fuel return hose clip. Remove fuel
return hose from regulator connecting pipe.
5.Plug connections.
6.Remove 4 nuts ignition coil bracket to inlet
manifold.
7.Release ignition coil bracket from inlet manifold
studs and place aside.
8.Release regulator connecting pipe from clip.
9.Disconnect vacuum hose from fuel pressure
regulator.
10.Remove 2 bolts securing fuel pressure regulator
to fuel rail.
11.Remove fuel pressure regulator assembly.
12.Remove 'O' ring and spacer ring from fuel
pressure regulator. Discard 'O' ring.
13.Release clip and remove connecting pipe from
regulator.
14.Fit plugs to regulator and rail.