1995 LAND ROVER DISCOVERY warning

MFI
17
REPAIR FUEL FILTER
Service repair no - 19.25.02
Remove
WARNING: Spilling of fuel is unavoidable
during this operation. Ensure all
necessary precautions are taken to
prevent fire and explosion.
WARNING: Ensure fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Access to filter is gained through right hand rear
wheel arch.
3.Clean area around hose connections to prevent
ingress of foreign matter into fuel system. Clamp
inlet and outlet hoses to prevent fuel spillage
when disconnecting hoses.
4.Loosen two fuel line unions and remove hoses.
Plug ends of hoses to prevent ingress of dirt.
5.Release securing bolt and bracket and remove
filter from chassis side member.
Refit
6.Fit a new filter observing direction of flow arrows
stamped on canister.
7.Tighten securing nut and bolt.
8.Fit inlet and outlet hoses. Tighten to
30Nm.
9.Refit fuel pump relay module, reconnect battery.
10.Start engine and inspect for fuel leaks around
hose connections.

19FUEL SYSTEM
18
REPAIR FUEL PIPES
Service repair no - 19.40.92
WARNING: Depressurise fuel system.See
Depressurise Fuel System
before
disconnecting any fuel pipes ensure that
all necessary precautions are taken against fuel
spillage
WARNING: Ensure fuel handling
precautions given in Section 01 -
introduction are strictly adhered to when
carrying out following instructions.
KEY
1. Fuel feed hose to fuel rail.
2. Fuel return hose to fuel tank.
3. Rigid fuel feed pipe.
4. Rigid fuel return pipe.
5. Fuel filter.6. Rigid fuel feed pipe to filter.
7. Breather hose.
8. In-tank fuel pump.
9. Fuel filler neck.
10. Fuel tank.

19FUEL SYSTEM
20
REPAIR ACCELERATOR PEDAL
Service repair no - 18.30.35
Remove
1.Remove lower dash panel.
2.Remove clevis pin securing throttle cable to
accelerator pedal.
3.Release tension from pedal return spring.
4.Remove circlip from pedal pivot pin.
5.Withdraw pivot pin.
NOTE: It may be necessary to lower
steering column to gain access to pivot
pin circlip.
6.Remove accelerator pedal.
Refit
7.Lightly grease pivot and clevis pins.
8.Fit clevis pin using aNEWcotter pin.
9.Reverse removal procedure.FUEL PUMP AND SENDER UNIT
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump/sender
unit is fitted. The fuel pump/sender unit is accessed
through a panel in the load space floor.
Fuel pump/sender unit
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Service Tools:
LRT-19-001 wrench - pump retaining ring
LRT-19-002 'Speedfit' disconnector
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Syphon at least 9 litres (2 gallons) of fuel from
fuel tank into a suitable container that can be
sealed.
4.Remove carpet from loadspace floor and
tailgate.
5.Fold back loadspace sound insulation to reveal
access panel.

MFI
21
REPAIR 6.Remove access panel from floor.
7.Disconnect multi-plug from fuel sender unit.
8.Disconnect two fuel line unions from fuel pump.
9.Using service tool no. LRT-19-001, remove
pump unit retaining ring. Withdraw unit from fuel
tank.
WARNING: A quantity of fuel will be
retained in body of unit, care must be
taken to prevent fuel spillage when unit is
removed.
Refit
10.Insert fuel pump into tank. Fit retaining ring.
Tighten to
48 Nm.
11.Connect fuel lines to pump.
12.Connect multi-plug to sender unit.
13.After assembly, check all fuel pipes, sealing
rings and hose connections are secure.
14.Run engine to check for fuel leaks.
15.Inspect access panel seal, fit a new seal if
necessary.
16.Fit access panel and tighten screws.
17.Reverse removal procedure. 4 - 5. Fit insulation
and carpet.

19FUEL SYSTEM
22
REPAIR FUEL TANK
Service repair no - 19.55.01
WARNING: Ensure that fuel handling
precautions given in Section 01 -
introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system. Disconnect battery
negative lead.
2.Syphon fuel tank into a suitable container that
can be sealed afterwards.
ENSURE TANK IS DRAINED COMPLETELY.
(refer to Warning concerning fuel vapour and
spillage at start of procedure).
3.Remove carpet loadspace floor and tailgate.
4.Fold back sound insulation to reveal access
panel.
5.Remove access panel.
6.Disconnect electrical multi-plug.
7.Disconnect two fuel line unions from fuel pump.
8.Working underneath vehicle mark location of
anti-roll [sway] bar straps.
9.Remove rear anti-roll [sway] bar straps, and
allow bar to swing down clear of tank.
10.Remove tank filler and vent hoses at fuel tank.
11.Remove nut and bolt securing right hand side
fuel tank strap.
12.Disconnect evaporative control pipe at green
end of 'speedfit' connector.
NOTE: To disconnect 'speedfit' connector,
insert forked end of LRT-19-002 into slots
of connector see illustration. Press down
on collet and simultaneously pull pipe from
connector.

SFI
3
REPAIR FUEL SYSTEM - DEPRESSURISE
WARNING: Fuel pressure of up to 2.5 bar
will be present in the system, even if the
engine has not been run for some time.
Always depressurise the system before
disconnecting any components in the fuel feed
line (between fuel pump and pressure regulator).
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
NOTE: Fuel pressure can be relieved at
fuel rail feed union or fuel filter unions.
1.Position cloth around relevant union to protect
against fuel spray.
2.Carefully slacken union.
3.Tighten union to correct torque once pressure
has relieved.

19FUEL SYSTEM
16
REPAIRADD: 09/95 RELAY MODULE - ADVANCED EVAPS
Service repair no - 18.30.71
Remove
1.Release module from bracket.
2.Disconnect 2 multiplugs from module.
3.Remove module.
Refit
4.Position module, connect multiplugs and secure
to bracket.FUEL FILTER - ADVANCED EVAPS
Service repair no - 19.25.02
Remove
WARNING: Spilling of fuel is unavoidable
during this operation. Ensure all
necessary precautions are taken to
prevent fire and explosion.
WARNING: Ensure fuel handling
precautions given in section 1 -
Introduction are strictly adhered to when
carrying out following instructions.
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Raise rear of vehicle.
WARNING: Support on safety stands.
3.Clean area around hose connections to prevent
ingress of foreign matter into fuel system. Clamp
inlet and outlet hoses to prevent fuel spillage
when disconnecting hoses.
4.Loosen 2 fuel line unions and disconnect hoses.
Remove and discard 'O' rings. Plug ends of
hoses to prevent ingress of dirt.
CAUTION: Use two spanners when
loosening or tightening unions.
5.Remove nut and bolt securing fuel filter bracket
to chassis and remove filter from bracket.

SFI
17
REPAIR ADD: 09/95 Refit
6.Fit a NEW filter to bracket.
NOTE: Ensure direction of flow arrow
stamped on canister is correct.
7.Position filter mounting bracket to chassis and
secure with nut and bolt.
8.Remove plugs from fuel hose ends.
9.Lubricate NEW 'O' rings with clean fuel and fit to
fuel hoses.
10.Connect fuel hoses to filter and tighten unions to
18 Nm.
CAUTION: Use two spanners when
loosening or tightening unions.
11.Remove stand(s) and lower vehicle.
12.Run the engine to check for any fuel leaks.FUEL PUMP AND GAUGE SENDER UNIT -
ADVANCED EVAPS
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump and
gauge sender unit is fitted. The top flange of the pump
also houses a pressure sensor which is not removable
from the pump. The fuel pump is accessed through a
panel in the load space floor.
WARNING: Ensure that fuel handling
precautions given in 01 - Introduction are
strictly adhered to when carrying out
following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Check the amount of fuel in the tank. If the tank
is full, drain 2.4 US gallons (9 litres) minimum.
See fuel tank - draining - advanced evaps
4.Remove 6 screws securing tail door tread strip
and remove tread strip.
5.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair, rear
compartment lower trim panels