1995 LAND ROVER DISCOVERY airbag

75SUPPLEMENTARY RESTRAINT SYSTEM
20
REPAIR
5.Position airbag module to toolSMD 4082/6.
Ensure module is correctly secured using all
fixings.
6.Ensure airbag module mounting brackets are
secure.
WARNING: Ensure tool SMD 4082/1 is not
connected to battery.
7.Connect flyleadSMD 4082/5to airbag module.
8.Connect flyleadSmd 4082/5to toolSMD 4082/1
WARNING: Do not lean over module whilst
connecting.
9.Connect toolSMD 4082/1to battery.
WARNING: Ensure all personnel are
standing at least 15 metres (50 ft) away
from module.

SUPPLEMENTARY RESTRAINT SYSTEM
21
REPAIR
10.Press both operating buttons to deploy airbag
module.
11. DO NOTreturn to airbag module for 30 minutes.
12.Using gloves and face mask, remove airbag
module from tool, place airbag module in plastic
bag and seal bag.
13.Wipe down tool with damp cloth.
14.Transport deployed airbag module to designated
area for incineration.
NOTE: DO NOT transport airbag module in
the vehicle passenger compartment. DO
NOT re-use or salvage any parts of the
airbag system.AIRBAG DIAGNOSTIC CONTROL UNIT - SPS SRS
Service repair no - 76.74.03
Remove
1.Remove centre console.
See CHASSIS AND
BODY, Repair, centre console.
2.Disconnect connector from control unit.
3.Remove 2 Torx bolts securing control unit to
body.
4.Remove control unit.
Refit
5.Position control unit to body, fit Torx bolts and
tighten to
10 Nm (7 lbf ft).
6.Connect control unit connector and secure.
7.Fit centre console.
See CHASSIS AND BODY,
Repair, centre console.
8.Check supplementary restraint system using
TestBook.

SUPPLEMENTARY RESTRAINT SYSTEM
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Airbag module screws 8 (6 lbf ft)...........................................................................
Steering wheel nut 50 (37 lbf ft)..............................................................................
Crash sensor screws (Distributed SRS) 10 (7 lbf ft)..............................................
Control unit 10 (7 lbf ft)...........................................................................................

CHASSIS AND BODY
47
REPAIR
14.Remove 2 screws securing louvre panel.
15.Remove louvre panel from dash panel.
Refit
16.Position louvre panel, feed harness connectors
through their correct apertures,and align to dash
panel.
CAUTION: When refitting avoid trapping of
electrical wiring.
17.Fit and tighten screws securing louvre panel.
18.Fit panel retaining screw cover.
19.Position heater control unit to panel and secure
with screws.
20.Fit heater graphic display panel and secure with
screws.
21.Fit heater control and blower switch knobs.
22.Fit clock.
See ELECTRICAL, Repair, clock.
23.Position coin tray and secure to tags.
24.Position radio cage, feed electrical connectors
and aerial through cage, and position to panel.
25.Bend back radio cage retaining tags.
26.Fit radio.
See ELECTRICAL, Repair, radio.
27.Connect battery negative lead.DASH PANEL ASSEMBLY
Service repair no - 76.46.23
Remove
1.Move front seats to rearmost position.
2.Disconnect battery negative lead.
3.Disconnect air bag multiplugs under dash panel.
CAUTION: When air bags are fitted,
reference must be made to the Airbag
Supplementary Restraint System section.
4.Remove passenger glove box.
5.Remove driver's side access panel.
6.Remove centre console assembly.
See centre
console.
7.Remove airbag from steering wheel.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, driver's airbag module.
8.Remove passenger's airbag from dash panel.
See SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, passenger's airbag module.
9.Release clamp and lower steering column.
10.Remove steering wheel.
See STEERING,
Repair, steering wheel.
11.Remove column switch.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, column switch assembly.
12.Remove instrument binnacle.See
ELECTRICAL, Repair, instrument binnacle.
13.Remove radio.See ELECTRICAL, Repair,
radio.
14.Remove exterior mirrors switch panel.
15.Remove coin tray.
16.Remove switch panel.
17.Remove clock.
18.Undo screw securing mounting bracket and
position passenger's side relay assembly aside.
19.Set heater controls fully clockwise.

ELECTRICAL
1
REPAIR FUSE BOX - INTERIOR
Right Hand Drive shown
The interior fusebox is fitted below the steering column, behind the trim panel. It comprises of three integral units.
'A'Main fusebox,'B'Satellite 2,'C'Satellite 1.
A label in the fusebox cover shows the circuits protected, the fuse rating and their locations. Access is by
releasing the fixing screws and lowering the panel.
'A' Main fusebox
1. Stop lights, direction indicators
2. LH side light
3. Radio/cassette/CD player
4. RH headlight main beam
5. LH headlight main beam
6. Cigar lighter
7. Airbag SRS
8. RH side lights
9. Rear fog guard lights
10. RH headlight dipped beam
11. LH headlight dipped beam
12. Multi-function unit
13. Ignition feed for Multi-function unit
14. Instruments, reversing lights
15. Air conditioning, windows
16. Washers & wipers - front
17. Starter, glow plug
18. Wash/wipe - rear, mirrors, cruise control
'B' Satellite 2
1. Electric windows - front
2. Electric windows - rear
3. Anti-lock braking
4. Central door locking
5. Electric sun roof
6. Trailer lights
'C' Satellite 1
1. Anti-theft alarm
2. Headlight washers
3. Engine management
4. Anti-lock brakes
5. Anti-theft alarm
6. Rear air conditioning, heater
'D' Spare fuses (5 off)