1995 LAND ROVER DISCOVERY weight

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.

ZF
3
REPAIR 19.Disconnect rear propeller shaft to output flange,
and tie to one side.
20.Repeat instructions 18 and 19 on front propeller
shaft to main gearbox.
21.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
22.Disconnect oil cooler feed and return pipes from
bottom and side of main gearbox.
23.Release cooler pipes from clamp at engine sump
and remove distance piece.
24.Blank pipe ends and unions.
25.Move oil cooler pipes clear of transmission and
tie aside.
26.Disconnect selector cable from operating lever.
27.Disconnect inhibitor switch at multiplug.
28.Attach adaptor plate to hoist.
29.Remove two bolts from transfer gearbox rear
cover.
30.Raise hoist to align adaptor plate with transfer
gearbox and transmission. Secure to transfer
gearbox at rear cover with two bolts removed.
31.Adjust hoist to take weight of transmission.
32.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
33.Repeat for the left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket
34.Remove right side mounting bracket to flexible
mounting rubber retaining nut.
35.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
36.Remove clip and clevis pin from park brake
lever.
37.Remove clip securing outer brake cable
38.The park brake cable is now free.
39.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
40.Remove ties securing breather pipes to harness.
41.Remove bell housing access plate complete with
gasket.
42.Rotate engine, using crankshaft pulley, until two
access holes are visible in drive plate/ring gear
assembly through bell housing bottom cover
opening.
43.Identify an access hole and bolt hole to aid
reassembly.
44.Remove bolts securing drive plate to convertor
through access holes.
45.Rotate crankshaft half turn to access and
remove remaining bolts.
46.Disconnect oil dipstick tube at main gearbox.
47.Remove bolt at bell housing and detach dipstick
tube. Blank pipe end and union.
48.Position hoist jack channel under engine and
support using a wooden block.
49.Remove bell housing to engine securing bolts,
also detach harness bracket from bell housing.
50.Ease transmission rearwards to allow access to
secure torque converter in bell housing.
51.Lower hoist and complete removal of
transmission.
Refit
52.Ensure torque converter is retained in bell
housing.
53.Secure transmission to adaptor plate on lifting
hoist.
54.Raise hoist and locate transmission with engine.
55.Remove torque converter retainer.
56.Complete attachment of transmission to engine
and fit bell housing bolts. Fit the dipstick tube
bracket and harness bracket to their respective
bolts.
57.Complete refitting by reversing removal
procedure. Note the following important points.
58.Drive plate to torque converter bolts are to be
coated with Loctite 290 prior to assembly.
59.Refill transfer and main gearboxes with correct
grade oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
60.Check operation of parking brake and adjust as
necessary.
See SECTION 10, Maintenance,
Vehicle Interior

44AUTOMATIC GEARBOX
6
REPAIR 13.Remove starter.
14.Working through starter aperture note position of
torque converter flexible drive plate to facilitate
refitting.
15.Remove the four torque convertor to flexible
drive securing bolts, rotating engine to gain
access to each individual bolt.
16.Raise vehicle on four post ramp [hoist].
17.Drain lubrication oil from transfer and main
gearboxes.
18.Disconnect speedometer cable from transfer
gearbox and disconnect associated clipping.
19.Remove rear propeller shaft.
See PROPELLER
SHAFTS, Overhaul, Flexible Coupling
20.Disconnect front propeller shaft at transfer
gearbox and tie to one side.
21.Remove exhaust front pipe.
22.Remove bolts securing front and centre silencer
mounting brackets and tie silencer to one side.
23.Disconnect oil cooler pipes from gearbox.
24.Blank off pipes and union connections.
25.Remove bolt securing retaining bracket to sump
and move cooler pipes aside.
26.Disconnect selector cable from lever on side of
gearbox.
27.Disconnect inhibitor switch multi-plug.
28.Disconnect park brake cable from linkage to park
brake lever.
29.Disconnect electrical connections from
differential lock switch on transfer gearbox.
30.Remove two lower bolts from transfer gearbox
input bearing support plate.
31.Assemble approved support cradle to
transmission hoist.32.Raise hoist and secure cradle to transfer
gearbox input bearing support plate using bolts
removed.
33.Disconnect gearbox mounting brackets from
chassis cross member.
34.Remove chassis cross member.
35.Lower transmission sufficiently to allow access
to items attached to top of gearbox.
36.Remove left hand gearbox mounting bracket
assembly.
37.Remove ties from breather pipes and harness.
38.Remove nut securing gearbox oil filler/dip stick
tube to bell housing.
39.Release union nut at gearbox sump and remove
filler/dipstick tube. Fit blanking plugs.
40.Support engine using a wooden block with a
suitable ramp [hoist] jack.
41.Remove nut securing kick down cable bracket to
bell housing.
42.Remove two bolts securing top of bell housing to
flywheel housing.
43.Remove nuts securing bell housing to flywheel
housing and withdraw transmission assembly
from engine.
44.Fit a suitable torque converter retaining strap to
the bell housing.
45.Remove hoist and transmission from under
vehicle.
46.Fit lifting eyes to transmission.
47.Using suitable chains and lifting tackle take
weight of transmission assembly.
48.Remove bolts securing transmission cradle to
transfer box and withdraw hoist complete with
cradle.
49.Refit bolts to cover plate.

ZF
7
REPAIR Accessories removal/fitting
If fitting a replacement transmission assembly to the
vehicle, remove the following items from the existing
assembly and fit to the replacement.
CAUTION: It is important to remove the
spacer from the extension shaft and fit
onto the replacement unit.
50.Breather pipe union and washers from main
gearbox.
51.Breather pipe, union and washers from transfer
gearbox.
52.Main gearbox selector lever.
53.RH mounting bracket assembly.
54.Oil cooler pipe unions.
55.Fit blanks to all apertures where unions have
been removed and blank off pipe ends.
Refit
1.Fit transmission to cradle and hoist.
2.Locate hoist under vehicle and remove torque
convertor retaining strap.
3.Ensure low range gear is engaged.
4.Apply approved sealant to bell housing face.
5.Carefully raise assembly, align bell housing with
flywheel housing and bring mating faces
together.
6.Fit nuts and bolts to secure transmission to
engine.
7.Locate electrical wiring and breather pipes to
position.
8.Secure kick down cable clip to bell housing.
9.Raise hoist sufficiently to take weight.
10.Remove block and jack from engine sump.
11.Fit filler/dipstick tube to gearbox sump and
secure bracket to bell housing.
12.Apply Loctite to torque convertor bolts
13.Working through starter aperture refit the four
torque convertor to flexible drive securing bolts,
rotating crankshaft to gain access to bolt
locations.
14.Refit starter and heatshield.
15.Secure breather pipes and harness with ties.
16.Fit left hand mounting bracket assembly to
gearbox.
17.Raise transmission and support with a suitable
ramp [hoist] jack.
18.Remove two bolts securing transmission to
cradle, lower hoist and remove from under
vehicle.
19.Apply Loctite to above bolts and fit to transfer
gearbox input bearing support plate.
20.Fit chassis cross member.21.Secure gearbox mounting brackets to chassis
cross member.
22.Remove ramp [hoist] jack.
23.Connect electrical leads to differential lock
switch.
24.Connect inhibitor switch multi-plug.
25.Connect selector cable to lever on side of
gearbox.
26.Connect oil cooler pipes to gearbox and secure
retaining bracket to gearbox sump.
27.Secure silencer to chassis and refit exhaust front
pipe.
28.Refit front propeller shaft to transfer gearbox.
29.Refit rear propeller shaft.
See PROPELLER
SHAFTS, Overhaul, Flexible Coupling
30.Connect speedometer cable to transfer gearbox.
31.Refill transfer gearbox with correct grade of
lubricating oil.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
32.Lower ramp [hoist] to ground level.
33.Reconnect turbo-charger hose to inter-cooler.
34.Reconnect top hose to radiator.
35.Refill cooling system with correct mixture of
coolant.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
36.Reconnect kick down cable to fuel injection
pump.
37.Secure breather pipe clip to rear of cylinder
head.
38.Engage harness with clips along top of
bulkhead.
39.On left hand drive vehicles only, connect
multi-plug to top of brake fluid reservoir.
40.Refit insulation pad to rocker cover and inlet
manifold, secure with oil filler cap.
41.Refit gaiter and knob to transfer gear lever.
42.Select high range gear.
43.Reconnect battery terminals.
44.Refill main gearbox with correct grade of
lubricating oil.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids

ZF
15
REPAIR GOVERNOR ASSEMBLY
Service repair no - 44.22.01
Remove
1.Remove transfer gearbox.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Drain oil from automatic gearbox.
3.Remove bolts securing left hand mounting
bracket to extension housing and withdraw
bracket.
4.Remove transfer gear lever housing securing
bolts and move housing aside.
5.Remove extension housing ensuring seal is not
damaged, remove and discard gasket.
6.Remove extension shaft retaining bolt, withdraw
shaft and discard 'O' ring seal. If Tdi vehicle
remove spacer.
7.Remove governor assembly.
8.Remove park gear from governor assembly.
9.Detach governor housing.
10.Remove security clip and counter weight.
11.Remove and discard 'O' ring seal from output
shaft and three seal rings from 'F' clutch
housing.
12.Clean all components.
13.If necessary detach parking pawl by removing
guide plates and withdrawing mechanism.Refit
14.Refit parking pawl mechanism if removed.
15.Fit and lubricate new seal rings to 'F' clutch
housing shaft, ensure they are correctly seated.
16.Apply petroleum jelly to a new 'O' ring seal. Fit to
output shaft
17.Fit park gear to governor assembly tightening
screws to correct torque.
18.Fit governor assembly to output shaft.
19.Fit extension shaft with spacer if Tdi. Fit new 'O'
ring under bolt head.
20.Fit extension housing, avoid damaging seal.
Tighten to
23 Nm.
21.Refit transfer gear lever housing to extension
housing.
22.Refit mounting bracket to extension housing.
Tighten to
52 Nm.
23.Refit transfer gearbox.See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
24.Refill automatic gearbox with correct grade of oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

44AUTOMATIC GEARBOX
16
REPAIR GOVERNOR HUB
Service repair no - 44.22.04
Remove
1.Remove transfer box.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Remove transfer gear selector housing.
3.Loosen nine bolts holding extension housing.
4.Remove extension housing ensuring that seal is
not damaged, discard gasket.
5.Remove extension shaft and retaining bolt with
'O' ring. If Tdi vehicle remove spacer.
6.Remove governor assembly with parking wheel.
7.Remove two screws holding governor housing.
8.Remove two bolts, remove parking wheel.
Discard governor hub.
9.Remove security clip and counter-weight.
10.Remove 'O' ring from output shaft and discard.
11.Remove three seal rings from 'F' clutch housing
shaft.
12.Inspect all parts for damage or wear, replace if
necessary.
Refit
13.Fit counterweight and security clip into new
governor hub.14.Secure governor housing to governor hub.
Tighten to
10Nm.
15.Fit parking wheel to governor hub. Tighten to10
Nm.
16.Fit three new seal rings onto F clutch housing
shaft, fit 'O' ring onto output shaft.
NOTE: To aid fitting of 'O' ring apply
petroleum jelly.
17.Push governor assembly and parking wheel onto
output shaft until seated.
NOTE: Apply petroleum jelly to 'O' ring.
Ensure seal rings are snapped together
and seated.
18.Fit new gasket to rear of gearbox. Fit extension
housing, avoid damaging seal.
19.Fit extension shaft,and spacer if Tdi, apply
Loctite 270 to retaining bolt. Using a new 'O'
ring, tighten bolt to
42 Nm.
20.Tighten nine extension housing nine bolts to23
Nm.
21.Fit transfer gear selector housing, tighten three
bolts to
25 Nm.
22.Refit transfer box.

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect ABS wiring harness multi-plug at
jump hose bracket, if applicable.
6.Disconnect shock absorbers.
7.Disconnect flexible brake hose at connection
under floor.
8.Disconnect lower links at axle.
9.Mark differential and propeller shaft flanges with
identification marks for assembly. Remove four
nuts and bolts. Lower propeller shaft and tie to
one side.10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.Disconnect anti-roll[sway] bar links to axle.
See
REAR SUSPENSION, Repair, Anti-Roll[Sway]
Bar Ball Joint Links
14.Remove axle assembly.
Refit
15.Position axle and fit lower links. Tighten to
176
Nm
16.Reverse removal procedure.
17.Tighten pivot bracket ball joint to axle to
176 Nm.
18.Tighten propeller shaft to differential drive flange
to
47 Nm
19.Bleed brake system.See BRAKES, Repair,
Brake System Bleed

FRONT AXLE AND FINAL DRIVE
1
REPAIR FRONT AXLE ASSEMBLY
Service repair no - 54.15.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets.
Refit bolts to prevent oil leakage.
9.Remove ABS sensor, if applicable.
10.Remove bolts from brake calipers and tie to one
side.
11.Remove nuts and washers securing shock
absorbers to axle.
12.Disconnect drag link from swivel pin housing
arm.
13.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
14.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
15.Lower axle assembly and remove road springs.
16.Disconnect anti-roll[sway] bar link.
See FRONT
SUSPENSION, Repair, Anti-Roll[Sway] Bar
Ball Joint Links
17.Remove axle assembly.
Refit
18.Position axle under vehicle, supporting left side
of axle.
19.Reverse removal procedure.
20.Tighten propeller shaft bolts to
47 Nm.
21.Tighten panhard rod to axle bracket to88 Nm.
22.Tighten drag link to hub arm to40 Nm.
23.Tighten upper swivel pin bolts.See
Specifications, torque, Torque Values
24.Tighten radius arms to axle bolts to197 Nm.
25.Tighten radius arms to chassis side member
nuts to
197 Nm.
26.Tighten track rod end to40 Nm.
Fit new split [cotter] pin.