1995 LAND ROVER DISCOVERY drain bolt

12ENGINE
4
REPAIR CYLINDER HEAD GASKETS - RENEW
Service repair no - 12.29.01
1.Drain cooling system.
See COOLING SYSTEM,
Adjustment, Coolant
2.Remove inlet manifold.See FUEL SYSTEM,
Repair, Intake Manifold
3.Remove generator.
4.If fitted, remove compressor.
See AIR
CONDITIONING, Repair, Compressor
5.Remove rocker shafts.See Rocker Shaft
Renew
6.Remove push rods.
7.Remove both exhaust manifolds.
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - V8i
8.Remove air cleaner assembly.See FUEL
SYSTEM, Repair, Air Cleaner Assembly
9.Remove air flow sensor.See FUEL SYSTEM,
Repair, Air Flow Sensor
10.Remove ground leads from rear of left hand
cylinder head
11.Right hand cylinder head - remove breather pipe
from lifting bracket.
12.Loosen cylinder head bolts, reversing tightening
sequence.
13.Remove cylinder heads.
14.Remove cylinder head gaskets.
15.Clean exhaust mating faces.
16.Clean head and block faces.
17.Fit new cylinder head gaskets, word TOP
uppermost. DO NOT use sealant.
18.Oil cylinder bores.
19.Clean threads of head bolts and lightly oil.
20.Locate cylinder heads on block.
21.Locate cylinder head bolts in position illustrated.
96 mm long bolts - 2, 4, 6, 7, 8, 9, 10
66 mm long bolts - 1, 3, 5
NOTE: There are no bolts fitted in the four
lower holes in each cylinder head.
NOTE: Left hand cylinder head illustrated,
arrow points to front of vehicle.
22.Tighten bolts progressively in sequence, shown
to
20 Nmthen a further 180°±5°
23.Reverse removal procedure. 1 to 11.

V8i
13
REPAIR
NOTE: Release bolts securing compressor
mounting bracket to engine and remove
bracket to enable temporary lifting eye
ETC 5964 to be fitted. Secure lifting eye to
mounting bracket fixing points with suitable bolts
of equivalent size, pitch and thread. Leave lifting
eye attached until engine is reinstalled in vehicle.
15.Place drain tray underneath vehicle.
16.Disconnect hose from reservoir to power
steering pump. Secure hose end above level of
fluid reservoir to avoid unnecessary loss of fluid.
17.Disconnect power steering pump to power
steering box hose. Seal hose and pump
openings with masking tape to prevent ingress of
dirt. Wipe away any fluid spillage from chassis or
steering box.
18.Disconnect fuel temperature and coolant
temperature sensor multi-plugs.
19.Disconnect leads from coil.
20.Identify each injector multi-plug for re-assembly
and disconnect plugs from injectors.
21.Manoeuvre harness from behind fuel rails and
place to one side clear of engine assembly.
22.Remove two clamps securing gearbox oil cooler
pipes to engine block.
23.Remove engine mounting fixings on both sides
of cylinder block.
24.Fit lifting chains to engine lifting eyes as shown
in illustration RR1780E.
1. L/H Front chain 356mm total overall length.
2. R/H Front chain 330mm total overall length.
3. R/H Rear chain 457mm total overall length.
NOTE: All chain dimensions are measured
from end of lifting hook to end of last link
in chain.
25.Fit chain lifting eye to a suitable engine hoist.
Raise hoist high enough to enable engine
mountings to be removed, and withdraw rubber
mountings.
26.Lower hoist until engine rests securely on engine
mounting brackets. Remove lifting chains and
hoist.
27.Disconnect two heater hoses located on top of
right hand rocker cover.
28.Remove ground strap from rear of left hand
cylinder head. DO NOT remove from retaining
clip.
29.Remove all electrical harnesses from retaining
clips at rear of engine.
30.Remove transmission breather pipes from
retaining clip on rear lifting eye.
31.Remove top two bolts securing bell housing to
cylinder block.
32.Raise front of vehicle, lower vehicle on to axle
stands.
33.Remove bell housing bottom cover. Remove
gasket from bell housing face.
34.Remove nuts securing exhaust downpipes to
manifolds, remove heat shield from right hand
side downpipe.
35.Remove electrical leads from starter motor
solenoid. Disconnect multi-plug from oil level
sensor on side of sump, if fitted.
NOTE: Instructions 37, 38 and 39 refer to
automatic vehicles only.
36.With assistance rotate engine at crankshaft
pulley until two access holes in drive plate/ring
gear assembly are visible.
37.Remove two bolts visible through access holes.
Mark one access hole and one bolt hole to
ensure unit is reassembled in its original position
38.Rotate crankshaft 180Ê until two remaining
access holes are visible, remove two bolts.

V8i
15
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Drain engine oil
See SECTION 10,
Maintenance, Under Vehicle Maintenance
2.Fit drain plug. Tighten to40 Nm.
3.If fitted, disconnect low oil level sensor multiplug.
4.Remove bolt securing dipstick tube to rocker
cover.
5.Working form the centre outwards, progressively
loosen and remove 17 bolts securing sump.
Remove sump.
6.Remove all traces of sealant from mating
surfaces of sump, cylinder block and front cover,
using a suitable solvent or plastic scraper.
7.Degrease mating surfaces of sump, cylinder
block and front cover.Refit
8.Apply RTV Hylosil White sealant to mating
surface of sump.
9.Position sump, tighten bolts finger tight.
10.Tighten bolts progressively in sequence shown.
Tighten to
18 Nm.
11.Fit bolt securing dipstick tube to rocker cover.
12.If fitted, connect low oil level sensor multiplug.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine
Adaptor plate to crankshaft 84........................................................................
Generator and power steering mounting bracket to cylinder head 30............
Cylinder head:
Stage 1: 20.............................................................................................
Stage 2: - Further 180°±5°
Drive plate to converter 39..............................................................................
Engine mountings to engine and chassis 55..................................................
Engine mounting rubbers to brackets 30........................................................
Flexible drive plate to crankshaft adaptor plate 41.......................................... **
Flywheel to crankshaft bolts 78....................................................................... **
Lifting eye to cylinder heads 39......................................................................
Main bearing cap rear bolts 92....................................................................... *
Oil sump drain plug 40....................................................................................
Oil sump to cylinder block 18..........................................................................
Rocker cover to cylinder head 9....................................................................
Rocker shaft bracket to cylinder head 38........................................................
Spark plug 21..................................................................................................
Starter motor attachment 44...........................................................................
* These bolts must have threads coated in lubricant EXP16A before assembly.
** These bolts must have threads coated in sealant Loctite 270
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.

4.0 V8
7
REPAIR 171.Route drive belt around pulleys.
172.Pivot tensioner downwards.
173.Align belt to tensioner and release tensioner.
174.Connect battery positive lead and tighten.
175.Secure terminal cover.
176.Align gearbox breather pipe, clip to engine lifting
eye and fit bolt. Tighten to
9 Nm.
177.Align and secure engine harness brackets to
inlet manifold and fit nuts. Tighten to
9 Nm.
178.Connect injector multiplugs.
179.Connect air intake temperature sensor multiplug.
180.Connect fuel temperature sensor multiplug.
181.Connect coolant temperature multiplug.
182.Connect temperature gauge connector.
183.Connect oil pressure switch Lucar.
184.Connect camshaft sensor multiplug and secure
to bracket.
185.Fit ignition coil bracket.
See FUEL SYSTEM
SFI, Repair, Ignition Coils
186.Position heater hose/pipe assembly.
187.Connect hose to inlet manifold.
188.Align pipe to bracket and fit bolt. Tighten to
9
Nm.
189.Tighten hose clip.
190.Connect heater return hose and tighten clip.
191.Remove plugs from fuel feed and return hose
connections.
192.Clean feed unions.
193.Connect return hose and tighten clip.
194.Connect feed hose union and tighten.
195.Remove cloth.
196.Connect purge hose.
197.Connect leads to generator, tighten terminal nuts
and fit cover.
198.Connect sensing Lucar.
199.Connect servo vacuum hose.
200.Position expansion tank and secure with fixings.
201.Connect hose and tighten clip.
202.Lower ramp.
203.Fit mass air flow sensor.
See FUEL SYSTEM
SFI, Repair, Mass Air Flow Sensor (MAF
Sensor)
204.Fit plenum chamber.See FUEL SYSTEM SFI,
Repair, Plenum Chamber
205.Fit radiator.See COOLING SYSTEM, Repair,
Radiator
206.Fit bonnet.See CHASSIS AND BODY, Repair,
Bonnet [Hood]
207.Reconnect battery negative lead.
208.Bleed power steering system.
See STEERING,
Repair, Power Steering System - Bleed
209.Drain engine oil and refill.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended Lubricants and Fluids - USA
Vehicles
210.Start engine. Check for fuel, coolant and oil
leaks.FRONT COVER GASKET
Service repair no - 12.65.04 - Front Cover Gasket
Remove
1.Disconnect battery negative lead.
2.Drain cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
3.Remove radiatorSee COOLING SYSTEM,
Repair, Radiator
4.Remove water pump pulley.See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
5.Slacken bottom hose clip. Remove hose from
water pump.
6.Raise vehicle on ramp.
7.Disconnect oil cooler hoses from front cover and
position aside. Plug hoses and connections.
8.Disconnect Lucar from oil pressure switch.

4.0 V8
11
REPAIR ROCKER COVER GASKET - RIGHT HAND
Service repair no - 12.29.41 - RH Cover Gasket
1.Depressurise fuel system.
See FUEL SYSTEM
SFI, Repair, Fuel System - Depressurise
2.Disconnect battery negative lead.3.Drain cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
NOTE: Leave hose disconnected.
4.Disconnect purge pipe from plenum chamber
hose.
5.Disconnect breather pipe from rocker cover.
6.Remove bolt securing coolant pipe brackets and
nut securing bracket to manifold.
7.Loosen hose clip and disconnect coolant return
hose from pipe.
CAUTION: Plug connection.
8.Loosen clip and disconnect fuel return hose from
pipe.
9.Disconnect fuel hose from injector pipe.
CAUTION: Use 2 spanners.10.Remove 2 nuts securing engine harness
brackets to manifold.
11.Release 4 ht leads from 2 brackets on rocker
cover.

12ENGINE
4
DESCRIPTION AND OPERATION CYLINDER BLOCK COMPONENTS
1. Cylinder block
2. Knock sensor
3. Crankshaft sensor
4. Bolt - crankshaft sensor
5. Locating dowel - cylinder head
6. Bolt - connecting rod
7. Piston
8. Piston ring - top compression
9. Piston ring - 2nd compression
10. Piston ring - oil control
11. Gearbox adapter plate
12. Bearing shell - big end - upper
13. Flywheel
14. Bolt - flywheel
15. Torx screw - gearbox adapter plate
16. Blanking plate
17. Bolt - blanking plate
18. Gasket
19. Bolt - crankshaft rear oil seal housing
20. Crankshaft rear oil seal and housing
21. Bolt - coolant pump cover
22. Coolant pump cover
23. Impeller
24. Sealing rings
25. 'O' ring
26. Bolts - coolant pump
27. 'O' ring
28. Coolant pump body
29. Thrust washer halves - upper
30. Bearing shell - main bearing - upper
31. Locating dowel - oil pump
32. Locating dowel - flywheel
33. Gudgeon pin34. Crankshaft
35. Bearing shell - big end - lower
36. Bearing cap - big end
37. Nut - big end bearing cap
38. Locating dowel - main bearing cap
39. Bearing caps - main bearings
40. Bolt - main bearing cap
41. Thrust washer halves - lower
42. Bearing shell - main bearing - lower
43. Woodruff keys
44. Dipstick
45. Bolt - dipstick tube
46. Dipstick tube
47. Bolts - sump
48. Gasket - sump
49. 'O' ring
50. Oil strainer
51. Bolts - oil strainer
52. Sump
53. Washer - drain plug
54. Drain plug
55. Oil filter element
56. Crankshaft front oil seal
57. Bolts - oil pump
58. Gasket - oil pump
59. Oil pump
60. Oil pressure switch
61. Crankshaft spigot bush
62. Crankshaft spigot bearing
63. Locating dowel - coolant pump
64. Connecting rod
65. Bolts belt tensioner mounting plate
66. Belt tensioner mounting plate
67. Bolt - gearbox adapter plate

Mpi
5
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1.Remove gearbox.
2.Remove clutch assembly.
3.Remove flywheel.
4.Drain engine oil.
5.Fit sump plug, replacing sealing washer if
damaged and tighten to the correct torque.
6.Loosen 15 sump bolts by approximately 3 turns,
allowing sump to drop away from rear oil seal
housing. Do not loosen 3 boltsAaround oil
pump housing.
7.Remove bolts securing oil seal housing, remove
seal and housing assembly.
Refit
1.Clean seal seating area of block and accessible
area of sump gasket. Sump gasket must be
replaced if damaged.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-061 over crankshaft boss and fit
oil seal and housing assembly.
4.Remove tool.
5.Fit and tighten seal housing bolts to correct
torque in sequence shown.
10Nm
6.Tighten sump bolts to correct torque and in the
correct sequence.
See Engine Sump Gasket
7.Fit flywheel.
8.Fit clutch assembly.
9.Fit gearbox.