1995 JEEP YJ radiator

INSTALLATION
(1) Install the cables to the heater control panel.
(2) Connect right vent door cable. DO NOT connect
the left door cable at this time.
(3) Open and close the right vent door (one time)
using the air control lever on the heater control
panel.
(4) Connect left vent door cable.
(5) Open and close both vent doors with the air
control lever. Verify that both vent doors open at the
same time.
HEATER CORE AND HOUSING
REVIEW ALL WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Drain coolant from the radiator.
(2) Disconnect heater hoses.
(3) Disconnect vent door cables.
(4) Disconnect blower motor wire.
(5) Disconnect defroster duct.
(6) Remove nuts that attach the heater housing
studs to the engine compartment side of the dash
panel.
(7) Remove heater housing assembly by tilting it
downward, to disengage it from the defroster duct.
Pull it rearward and out from under the instrument
panel.
(8) Remove heater hosing cover from the housing.
(9) Remove heater core from the housing.
INSTALLATION
(1) Install the heater core into the housing and in-
stall the cover on the housing.
(2) Position heater housing on the dash panel. Be
sure the housing studs all extend through the dash
panel.
(3) Install the seals on the heater core outlet and
inlet tubes and over the blower motor housing.
(4) Install attaching nuts on the housing studs.
CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tighten
the nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(5) Connect defroster duct to the housing.
(6) Connect blower motor wire.
(7) Connect vent door control cables.
(8) Connect heater hoses.
(9) Fill cooling system.
(10) Check system operation.
BLOWER MOTOR (HEATING)
REMOVAL
(1) Remove heater housing.
(2) Remove blower motor-to-heater housing attach-
ing screws/nuts.
(3) Remove blower motor from the housing.
INSTALLATION
(1) Position blower motor into housing.
(2) Install and tighten blower motor-to-heater
housing attaching screws/nuts.
(3) Install heater housing.
(4) Check blower motor and heater operation.
DEFROSTER NOZZLE AND DUCT
REVIEW ALL WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Drain coolant from the radiator.
(2) Disconnect heater hoses.
(3) Remove nuts attaching the heater housing
studs to the engine compartment side of the dash
panel.
(4) Disconnect speedometer cable.
(5) Remove glove box.
(6) Tilt heater housing back and pull it rearward
and out from under the instrument panel.
(7) Disconnect vent control cables.
(8) Remove fresh air intake grille from the cowl.
(9) Remove fresh air intake duct.
(10) Lower windshield.
(11) Remove defroster nozzle attaching screws and
remove the nozzle and duct.
INSTALLATION
(1) Install defroster nozzle and duct.
(2) Raise and secure the windshield.
(3) Install fresh air intake duct.
(4) Install fresh air intake grille on the cowl.
(5) Install vent cables.
(6) Position heater housing on the dash panel. Be
sure all the housing studs extend through the dash
panel.
(7) Install seals on the blower motor and heater
core inlet and outlet tubes.
(8) Install on the housing studs.
CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tighten
the nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(9) Install glove box.
(10) Connect speedometer cable.
JHEATING AND AIR CONDITIONING 24 - 33

(11) Connect the heater hoses.
(12) Fill cooling system.
FRESH AIR DOOR VACUUM MOTOR
REMOVAL
(1) Remove glove box and assist handle.
(2) Disconnect vacuum hose from the motor.
(3) Remove motor lever retaining clip.
(4) Remove motor attaching nuts and remove the
motor from the fresh air duct.
INSTALLATION
(1) Position motor on fresh air duct and install the
motor attaching nuts.
(2) Align motor lever with the air door lever and
install the lever retaining clip.
(3) Connect vacuum hose to the motor.
(4) Install glove box and assist handle.
FRESH AIR INTAKE DUCT
REVIEW WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Drain coolant from the radiator.
(2) Disconnect heater hoses.
(3) Remove nuts attaching the heater housing
studs to the dash panel from inside the engine com-
partment.
(4) Disconnect speedometer cable.
(5) Remove glove box and assist handle.
(6) Tilt heater housing back and pull it rearward
and out from under the instrument panel.
(7) Disconnect vent cables.
(8) Remove windshield bracket bolts and lower
windshield.
(9) Remove fresh air intake grille from the cowl.
(10) Remove fresh air intake duct.
INSTALLATION
(1) Install fresh air intake duct.
(2) Install defroster nozzle and duct.
(3) Raise and secure the windshield.
(4) Install fresh air grille on the cowl.
(5) Install vent cables.
(6) Position heater housing on the dash panel. Be
sure all the housing studs extend through the dash
panel.
(7) Install seals on the blower motor and heater
core inlet and outlet tubes.
(8) Install nuts on the heater housing studs.
CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tightenthe nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(9) Install glove box and assist handle.
(10) Connect speedometer cable.
(11) Connect heater hoses.
(12) Fill cooling system.
TEMPERATURE CONTROL THERMOSTAT
REMOVAL
(1) Remove mounting bolts and lower the evapora-
tor housing.
(2) Remove the attaching screws holding the top
and bottom housings together.
(3) Separate the housings.
(4) Remove the thermostat.
INSTALLATION
(1) Install temperature control thermostat. Insert
thermostat capillary tube into the evaporator coil a
minimum of 50 mm (2 inch).
CAUTION: Handle the tube with care to avoid bends
or kinks that could cause the thermostat to mal-
function.
(2) Assemble the housing and install the attaching
screws. DO NOT over tighten the attaching screws.
(3) Install the evaporator housing.
A/C CONDENSER
REVIEW WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Recover refrigerant from A/C system.
(2) Drain the radiator.
(3) Remove fan shroud and radiator.
(4) Disconnect A/C line from the condenser.
(5) Remove condenser attaching screws and tilt the
bottom of the condenser toward the engine.Plug all
the condenser openings to prevent entry of dirt
or moisture.
(6) Working from under the vehicle, disconnect the
receiver-drier to-evaporator hose fitting from the re-
ceiver-drier.
(7) Remove condenser and receiver-drier as an as-
sembly.
(8) Remove receiver-drier from the condenser, if
necessary.
INSTALLATION
Add 30 ml (1 fluid oz.) of refrigerant oil to the A/C
system if the condenser is replaced.
(1) Attach receiver-drier to the condenser.
(2) Install condenser and connect A/C line to the
receiver-drier.
24 - 34 HEATING AND AIR CONDITIONINGJ

(3) Install condenser attaching screws.
(4) Connect condenser A/C line.
(5) Install radiator and fan shroud.
(6) Fill coolant system (Refer to cooling for proper
procedure).
(7) Evacuate, charge and leak test the air condi-
tioning system.
RECEIVER-DRIER REPLACEMENT
REVIEW ALL WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Recover refrigerant from A/C system.
(2) Disconnect A/C lines from the receiver-drier.
(3) Remove receiver-drier attaching screws and re-
move receiver-drier.
INSTALLATION
(1) Position receiver-drier in place and install re-
ceiver-drier attaching screws.
(2) Connect A/C lines to receiver-drier.
(3) Evacuate, charge and leak test the air condi-
tioning system.
EVAPORATOR AND HOUSING
REVIEW ALL WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Recover refrigerant from A/C system.
(2) Disconnect A/C lines.
(3) Remove hose clamps and dash grommet retain-
ing screws.
(4) Remove the evaporator housing-to-instrument
panel attaching screws and the housing mounting
bracket screw (Fig. 3).
(5) Lower the evaporator housing and pull the
hoses and hose grommet through the dash opening.(6) Remove upper housing and remove evaporator.
The evaporator core, control switches, expansion
valve, blower motor and housing can be serviced af-
ter removing evaporator housing (Fig. 4).
INSTALLATION
Add 30 ml (1 fluid oz.) of refrigerant oil to the A/C
system if the evaporator is replaced.
(1) Install evaporator into housing and install up-
per housing.
(2) Push A/C hoses through the grommet openings
and install the hose grommet by pushing it toward
the engine compartment.
(3) Install hose grommet attaching screws.
(4) Raise evaporator housing and install the evap-
orator housing-to- instrument panel attaching
screws.
(5) Install A/C lines.
(6) Evacuate, charge and leak test the system.
EXPANSION VALVE
REVIEW WARNINGS AND CAUTIONS IN
THIS GROUP BEFORE PERFORMING THIS
OPERATION.
REMOVAL
(1) Recover refrigerant from A/C system.
(2) Remove evaporator housing
(3) Remove the insulation wrapped around the suc-
tion hose fitting, expansion valve and evaporator tub-
ing.
(4) Mark the capillary tube location on the evapo-
rator tubing.
(5) Disconnect inlet and outlet hose fittings, and
remove the capillary tube clamp.
(6) Disconnect and remove the expansion valve.
INSTALLATION
(1) Clean evaporator tubing to provide a positive
contact with the expansion valve capillary tube.
(2) Install expansion valve.
(3) Clamp the capillary tube at the marked loca-
tion on the evaporator tubing.
(4) Connect inlet and outlet hose fittings.The
capillary tube must be securely clamped and
have positive metal-to-metal contact with the
evaporator tubing.
(5) Wrap expansion valve, inlet hose fitting and
capillary tube with insulation.
(6) Install evaporator housing.
(7) Evacuate, charge and leak test the system.
A/C BLOWER MOTOR
It is not necessary to discharge the system to ser-
vice the blower motor. The evaporator housing need
only be lowered for access to the blower motor at-
taching screws.Fig. 3 Evaporator Housing
JHEATING AND AIR CONDITIONING 24 - 35

ANTENNA........................8F-2,8F-5
ANTENNA, POWER; RADIO (XJ-RHD) . . . 8W-47-1
ANTENNA REMOVE/INSTALL - XJ.........8F-8
ANTENNA REMOVE/INSTALL - YJ........8F-10
ANTILOCK BRAKES (ABS)................5-1
ANTILOCK BRAKING MODE, ABS
OPERATION IN.......................5-36
ANTILOCK ECU AND HCU DIAGNOSIS......5-3
APPLICATION CHARTS, GEARTRAIN
OPERATION........................21-169
APPLICATION, TRANSMISSION..........21-67
APPLICATIONÐXJ VEHICLES, BULB......8L-18
APPLICATIONÐYJ VEHICLES, BULB......8L-32
APPLIQUEÐXJ, QUARTER WINDOW.....23-25
APPLIQUEÐYJ, RADIATOR GRILLE.....23-104
APRONSÐYJ, FENDER SPLASH........23-115
ARM, LOWER SUSPENSION.............2-13
ARM, PITMAN..................19-17,19-20
ARM REMOVE/INSTALL, LIFTGATE
WIPER.............................8K-17
ARM REMOVE/INSTALL, WINDSHIELD
WIPER.............................8K-17
ARM, UPPER SUSPENSION.............2-12
ARMING/DISARMING MECHANISM;
RESTRAINT SYSTEMS.................8M-2
ARMING/DISARMING MECHANISM;
STEERING..........................19-48
ARMS AND PUSH RODS, ROCKER....9-23,9-65
ASH RECEIVER TRAY LAMPÐXJ, I/P.....23-80
ASSEMBLY....................19-63,19-71
ASSEMBLY AND ADJUSTMENT, VALVE
BODY.............................21-153
ASSEMBLY, CALIPER...................5-50
ASSEMBLY, COMPRESSOR CLUTCH......24-20
ASSEMBLY, DIFFERENTIAL; FRONT
SUSPENSION AND AXLE................2-38
ASSEMBLY, DIFFERENTIAL; REAR
SUSPENSION AND AXLES...............3-21
ASSEMBLY, FINAL; FRONT SUSPENSION
AND AXLE...........................2-46
ASSEMBLY, FINAL; REAR SUSPENSION
AND AXLES..........................3-29
ASSEMBLY, FUEL RAIL................14-62
ASSEMBLY, GEAR....................19-43
ASSEMBLY, IMPACT SENSOR/INFLATOR . . . 8M-2
ASSEMBLY, PINION MEASUREMENT.......3-22
ASSEMBLY REMOVE/INSTALL, CLUSTER . . 8E-17,
8E-35
ASSEMBLY REPLACEMENT, ADJUSTER
PLUG..............................19-29
ASSEMBLY REPLACEMENT, COLUMN.....19-52
ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE AXLE; FRONT
SUSPENSION AND AXLE................2-23
ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE AXLE; REAR
SUSPENSION AND AXLES...........3-14,3-31
ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE AXLE; FRONT
SUSPENSION AND AXLE................2-24
ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE AXLE; REAR
SUSPENSION AND AXLES...............3-14
ASSEMBLY (SHORT BLOCK), SERVICE
ENGINE..............................9-4
ASSEMBLY TIPS, TRANSMISSION......21-155
ASSEMBLY, TRANSFER CASE
....21-294,21-319
ASSEMBLY/INSTALLATION, PINION GEAR
. . 2-42
ASSEMBLYÐXJ VEHICLES, ENGINE
. . . 9-18,9-59
ASSEMBLYÐYJ VEHICLES, ENGINE
. . . 9-20,9-62
ASSIST HANDLEÐXJ
.................23-89
ASSIST HANDLEÐYJ, FULL-METAL
DOOR
............................23-136
AUTO SHUTDOWN (ASD) RELAYÐPCM
OUTPUT
............................14-26
AUTOMATIC BELT TENSIONERÐXJ
MODELS WITH RIGHT HAND DRIVE
.......7-42
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (XJ)
................8W-30-1
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (YJ)
................8W-30-1
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (XJ-RHD)
............8W-30-1
AUTOMATIC SHUTDOWN (ASD) RELAY;
FUEL SYSTEM
.......................14-59
AUTOMATIC SHUTDOWN (ASD) RELAY;
IGNITION SYSTEMS
..............8D-17,8D-1AUTOMATIC SHUTDOWN (ASD) RELAY
TEST...............................8D-6
AUTOMATIC SHUTDOWN (ASD) RELAY
TESTING...........................14-46
AUTOMATIC SHUTDOWN (ASD)
SENSEÐPCM INPUT..................14-21
AUTOMATIC TRANSMISSION............0-23
AUTOMATIC TRANSMISSION, 30RH/
32RH..............................21-67
AUTOMATIC TRANSMISSION, AW-4.....21-165
AUTOMATIC TRANSMISSION SHIFTER/
IGNITION INTERLOCK MECHANISM......19-55
AUXILIARY ELECTRIC COOLING FANÐXJ
MODELS WITH 4.0L 6-CYLINDER
ENGINE.............................7-35
AW-4 ACCUMULATOR COMPONENT
IDENTIFICATION....................21-342
AW-4 AUTOMATIC TRANSMISSION......21-165
AW-4 BUSHING AND PISTON
CLEARANCE........................21-339
AW-4 CLUTCH AND BRAKE PACK
REQUIREMENTS....................21-341
AW-4 CLUTCH DISC AND PLATE
THICKNESS........................21-338
AW-4 GENERAL SPECIFICATIONS.......21-337
AW-4 IN-VEHICLE SERVICE............21-182
AW-4 OIL PUMP WEAR LIMITS........21-338
AW-4 RETAINER AND PISTON
SPECIFICATIONS....................21-340
AW-4 TORQUE SPECIFICATIONS........21-344
AW-4 TRANSMISSION DIAGNOSIS......21-176
AW-4 TRANSMISSION OVERHAUL......21-201
AW-4 TRANSMISSION REMOVAL AND
INSTALLATION......................21-198
AW-4 VALVE AND SPRING
IDENTIFICATION....................21-343
AW-4 VALVE BODY CHECK BALL
DIMENSIONS.......................21-341
AWAY, PEDAL FALLS....................5-5
AX 15 MANUAL TRANSMISSION........21-33
AX 4/5 MANUAL TRANSMISSION.........21-1
AXLE (2WD), MODEL 30 AXLE AND
TUBE...............................2-22
AXLE, 8 1/4......................3-30,3-51
AXLE ALIGNMENT, REAR...............3-10
AXLE AND TUBE AXLE (2WD), MODEL
30 .................................2-22
AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE; FRONT
SUSPENSION AND AXLE................2-23
AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE; REAR SUSPENSION
AND AXLES......................3-14,3-31
AXLE ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE; FRONT
SUSPENSION AND AXLE................2-24
AXLE ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE; REAR SUSPENSION
AND AXLES..........................3-14
AXLE BUSHING REPLACEMENT......2-12,2-34
AXLE, FRONT DRIVE....................2-3
AXLE, MODEL 30.....................2-49
AXLE, MODEL 30 FRONT...............2-49
AXLE, MODEL 35.................3-13,3-51
AXLE NOISE/VIBRATION DIAGNOSIS;
FRONT SUSPENSION AND AXLE..........2-18
AXLE NOISE/VIBRATION DIAGNOSIS;
REAR SUSPENSION AND AXLES
..........3-9
AXLE SHAFT
.........................3-16
AXLE SHAFT, HUB BEARING
.............2-25
AXLE SHAFT OIL SEAL REPLACEMENT,
INNER
..............................2-35
AXLE SHAFT SEAL AND BEARING
........3-17
AXLE SHAFT, SEAL AND BEARING
SERVICE
............................3-32
AXLE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE
................2-49
AXLE SPECIFICATIONS; REAR
SUSPENSION AND AXLES
...............3-51
AXLEÐYJ VEHICLES, VACUUM
DISCONNECT
.........................2-27
AXLES
...............................3-1
AXLES, FRONT AND REAR
..............0-24
AXLE/SHIFT MOTOR DIAGNOSIS
(CONT'D), DISCONNECT
................2-30
AXLE/SHIFT MOTOR DIAGNOSIS,
DISCONNECT
.........................2-29BACKLASH AND CONTACT PATTERN
ANALYSIS; FRONT SUSPENSION AND
AXLE...............................2-45
BACKLASH AND CONTACT PATTERN
ANALYSIS; REAR SUSPENSION AND
AXLES..............................3-27
BACK-UP LAMPS; REAR LIGHTING (XJ) . 8W-51-1
BACK-UP LAMPS; REAR LIGHTING
(XJ-RHD).........................8W-51-1
BACK-UP LAMPS; REAR LIGHTING (YJ) . 8W-51-1
BACK-UP/REAR TURN SIGNAL/TAIL
LAMP BULB REPLACEMENTÐXJ........8L-12
BACK-UP/REAR TURN SIGNAL/TAIL
LAMP BULB REPLACEMENTÐYJ........8L-28
BALANCE, TIRE AND WHEEL............22-6
BALL DIMENSIONS, AW-4 VALVE BODY
CHECK............................21-341
BALL STUD REPLACEMENTÐXJ,
LIFTGATE SUPPORT ROD..............23-63
BALL STUDS, STEERING KNUCKLE.......2-32
BAR, STABILIZER; FRONT SUSPENSION
AND AXLE.......................2-11,2-15
BAR, STABILIZER; REAR SUSPENSION
AND AXLES...........................3-5
BAR, TRACK; FRONT SUSPENSION AND
AXLE...........................2-11,2-15
BAR, TRACK; REAR SUSPENSION AND
AXLES...............................3-8
BARÐXJ, SOUND....................23-94
BARÐYJ, SPORT...................23-132
BARRIERÐXJ, CARGO...............23-101
BASE COAT/CLEAR COAT FINISH.........23-158
BATTERY; BATTERY/STARTER/
GENERATOR SERVICE..................8B-1
BATTERY; BATTERY/STARTING/
CHARGING SYSTEMS DIAGNOSTICS......8A-2
BATTERY; LUBRICATION AND
MAINTENANCE.......................0-20
BATTERY CHARGING...................8A-7
BATTERY CHARGING TIME TABLE........8A-8
BATTERY CLASSIFICATIONS AND
RATINGS...........................8A-23
BATTERY DIAGNOSIS..................8A-4
BATTERY FEED; FUEL/IGNITION (XJ) . . . 8W-30-1
BATTERY FEED; FUEL/IGNITION (YJ) . . . 8W-30-2
BATTERY FEED; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
BATTERY RATINGS....................8A-3
BATTERY REMOVE/INSTALL.............8B-1
BATTERY SPECIFICATIONS; BATTERY/
STARTER/GENERATOR SERVICE..........8B-8
BATTERY SPECIFICATIONS; BATTERY/
STARTING/CHARGING SYSTEMS
DIAGNOSTICS.......................8A-23
BATTERY TRAYÐXJ..................23-14
BATTERY TRAYÐYJ.................23-110
BATTERY VOLTAGEÐPCM INPUT........14-21
B/C-PILLAR AND LIFTGATE PILLAR TRIM
COVERSÐXJ........................23-88
BEARING AND AXLE SHAFT, HUB.........2-25
BEARING, AXLE SHAFT SEAL............3-17
BEARING LUBRICANTS, CHASSIS
COMPONENT AND WHEEL..............0-28
BEARING NOISE, GEAR; FRONT
SUSPENSION AND AXLE................2-18
BEARING NOISE, GEAR; REAR
SUSPENSION AND AXLES................3-9
BEARING REPLACEMENT, PILOT..........6-12
BEARING REPLACEMENT, PITMAN
SHAFT SEALS.......................19-34
BEARING REPLACEMENT, RELEASE.......6-11
BEARING SERVICE, AXLE SHAFT, SEAL....3-32
BEARINGS, CRANKSHAFT MAIN......9-45,9-87
BEARINGS, FRONT WHEEL..............0-28
BELT, ACCESSORY DRIVE...............0-21
BELT DIAGNOSIS......................7-38
BELT INDICATOR WARNING LAMP, SEAT;
INSTRUMENT CLUSTER (XJ).........8W-40-2
BELT INDICATOR WARNING LAMP, SEAT;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
BELT SCHEMATICS....................7-38
BELT SERVICEÐEXCEPT RIGHT HAND
DRIVE
..............................7-40
BELT SERVICEÐXJ MODELS WITH
RIGHT HAND DRIVE
...................7-42
BELT SWITCH, DRIVER'S SEAT
......8U-1,8U-3
BELT TENSION, DRIVE
.................7-45
BELT TENSION SPECIFICATIONS
..........7-38
2 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

BUMPERÐXJ, LIFTGATE LICENSE PLATE
SCREW ANCHOR.....................23-65
BUMPERÐXJ, REAR SEATBACK LATCH
STRIKER...........................23-84
BUMPERS......................13-16,13-5
BUS, CCD; FUEL/IGNITION (XJ).......8W-30-5
BUSHING AND PISTON CLEARANCE,
AW-4 .............................21-339
BUSHING REPLACEMENT, AXLE......2-12,2-34
BUSHING REPLACEMENT, LEAF SPRING
EYE; FRONT SUSPENSION AND AXLE.....2-17
BUSHING REPLACEMENT, LEAF SPRING
EYE; REAR SUSPENSION AND AXLES . . . 3-5,3-7
BUSHINGS, CLUTCH AND BRAKE PEDAL . . . 0-22
BUZZER, COMBINATION; INTERIOR
LIGHTING (YJ)....................8W-44-1
BUZZER MODULE.................8U-1,8U-2
BUZZER MODULE SCHEMATIC - YJ.......8U-4
CABLE, ACCELERATOR PEDAL AND
THROTTLE.....................14-17,14-58
CABLE ADJUSTMENT, PARK INTERLOCK . 21-195
CABLE ADJUSTMENT, SHIFT...........21-195
CABLE ADJUSTMENT, TRANSMISSION
THROTTLE.........................21-194
CABLE ADJUSTMENT, TRANSMISSION
THROTTLE VALVE....................21-71
CABLE ADJUSTMENT (XJ), PARK
INTERLOCK........................21-101
CABLE ADJUSTMENT (XJ), SHIFT.......21-100
CABLE ADJUSTMENT (XJ/YJ), THROTTLE
VALVE..............................21-101
CABLE REMOVE/INSTALL, SERVO.......8H-10
CABLE REPLACEMENT, TRANSMISSION
THROTTLE.........................21-193
CABLE REPLACEMENT (XJ), PARKING
BRAKE REAR.........................5-67
CABLE REPLACEMENT (YJ), PARKING
BRAKE FRONT........................5-67
CABLE REPLACEMENT (YJ), PARKING
BRAKE REAR.........................5-68
CABLE REPLACEMENTÐXJ, LATCH
RELEASE...........................23-11
CABLE RESISTANCE, SPARK PLUG......8D-14
CABLE, SERVO.......................8H-1
CABLE, SPEEDOMETER.................0-33
CABLE TENSIONER ADJUSTMENT
(XJ/YJ), PARKING BRAKE...............5-69
CABLE TENSIONER REPLACEMENT (XJ),
PARKING BRAKE......................5-66
CABLE, THROTTLE...................14-17
CABLE/LINKAGE ADJUSTMENT,
GEARSHIFT.........................21-71
CABLES, DISTRIBUTOR CAP AND
ROTOR, IGNITION.....................0-20
CABLES, SPARK PLUG SECONDARY.....8D-14,
8D-24
CABLES, VENT DOOR CONTROL.........24-32
CALIBRATION, COMPASS...............8C-5
CALIPER ASSEMBLY...................5-50
CALIPER CLEANING AND INSPECTION.....5-50
CALIPER DISASSEMBLY................5-48
CALIPER INSTALLATION................5-51
CALIPER OPERATION AND WEAR
COMPENSATION......................5-45
CALIPER REMOVAL....................5-48
CAMSHAFT......................9-32,9-74
CAMSHAFT PIN REPLACEMENT......9-34,9-75
CAMSHAFT POSITION SENSOR; FUEL
SYSTEM............................14-60
CAMSHAFT POSITION SENSOR;
FUEL/IGNITION (XJ)................8W-30-3
CAMSHAFT POSITION SENSOR;
FUEL/IGNITION (YJ)................8W-30-3
CAMSHAFT POSITION SENSOR;
IGNITION SYSTEMS..............8D-17,8D-2
CAMSHAFT POSITION SENSOR;
FUEL/IGNITION (XJ-RHD)............8W-30-3
CAMSHAFT POSITION SENSOR TEST;
FUEL SYSTEM.......................14-46
CAMSHAFT POSITION SENSOR TEST;
IGNITION SYSTEMS
...................8D-6
CAMSHAFT POSITION SENSORÐPCM
INPUT
.............................14-22
(CANADA ONLY)ÐXJ, DAYTIME
RUNNING LIGHTS
....................8L-15
(CANADA ONLY)ÐYJ, DAYTIME
RUNNING LIGHTS
....................8L-30
CANISTER, EVAP
..................25-4,25-7CAP AND ROTOR, IGNITION CABLES,
DISTRIBUTOR........................0-20
CAP, DISTRIBUTOR....................8D-7
CAP, FUEL TANK FILLER TUBE;
EMISSION CONTROL SYSTEMS......25-4,25-7
CAP, FUEL TANK FILLER TUBE; FUEL
SYSTEM............................14-13
CAP, RADIATOR PRESSURE.............7-25
CAPACITIES, COOLING SYSTEM..........7-45
CAPACITIES, FLUID.....................0-3
CAPACITIES, FUEL TANK..........14-13,14-67
CAPACITY TEST, FUEL PUMP............14-7
CAR REPLACEMENT, PITMAN SHAFT
SEALSÐIN.........................19-23
CARDAN (CV), DOUBLE................16-11
CARDAN, SINGLE....................16-10
CARGO BARRIERÐXJ................23-101
CARGO LAMP AND DOME LAMP;
INTERIOR LIGHTING (XJ-RHD)........8W-44-1
CARGO LAMP, COURTESY LAMPS AND
DOME LAMP; INTERIOR LIGHTING (XJ) . 8W-44-1
CARGO LAMPÐXJ...................23-94
CARPET/MATÐXJ, FRONT.............23-99
CARPET/MATÐXJ, REAR.............23-100
CARPETÐYJ.......................23-156
CARPETS AND FLOOR MATSÐXJ.......23-99
CARRIERÐYJ, EXTERNAL SPARE/
WHEEL TIRE.......................23-133
CASE (4WD VEHICLES), TRANSFER........0-24
CASE ASSEMBLY, TRANSFER....21-294,21-319
CASE CHANGES, TRANSFER...........21-307
CASE CLEANING AND INSPECTION,
TRANSMISSION.....................21-125
CASE COVER OIL SEAL REPLACEMENT,
TIMING.........................9-30,9-73
CASE COVER, TIMING..............9-31,9-72
CASE DISASSEMBLY AND OVERHAUL,
TRANSFER...................21-289,21-310
CASE IDENTIFICATION, TRANSFER.....21-284,
21-307
CASE INSTALLATION, TRANSFER . 21-288,21-309
CASE LUBRICANT AND FILL LEVEL,
TRANSFER.........................21-284
CASE, NP231 TRANSFER.......21-283,21-305
CASE, NP242 TRANSFER.......21-307,21-331
CASE OVERHAUL, FIRST-REVERSE
BRAKE PISTON AND TRANSMISSION....21-247
CASE REMOVAL, TRANSFER.....21-287,21-309
CASE SKID PLATE, TRANSFER......13-15,13-3
CASE SPECIFICATIONS, TRANSMISSION/
TRANSFER.........................21-333
CATALYTIC CONVERTER............11-1,11-4
CATALYTIC CONVERTOR................25-1
CAUTIONS, AND WARNINGS, NOTES;
WIRING DIAGRAMSÐGENERAL
INFORMATION (XJ)...................8W-1
CCD BUS; FUEL/IGNITION (XJ)........8W-30-5
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)ÐXJ.......................8L-12
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)ÐYJ.......................8L-28
CERTIFICATION LABEL, VEHICLE SAFETY . Intro.-4
CHAIN AND SPROCKETS, TIMING....9-31,9-73
CHANGE AND FILTER REPLACEMENT,
ENGINE OIL
..........................0-16
CHANGE, LUBRICANT; FRONT
SUSPENSION AND AXLE
................2-23
CHANGE, LUBRICANT; REAR
SUSPENSION AND AXLES
...........3-13,3-31
CHANGE, REFILLING AFTER OVERHAUL
OR FLUID/FILTER
..............21-100,21-182
CHANGES AND PARTS
INTERCHANGEABILITY, TRANSMISSION
. . . 21-67
CHANGES, TRANSFER CASE
...........21-307
CHANNEL REPLACEMENTÐYJ, DOOR
FRAME GLASS
......................23-142
CHARGING, BATTERY
..................8A-7
CHARGING REFRIGERANT SYSTEM
......24-11
CHARGING SYSTEM; BATTERY/
STARTING/CHARGING SYSTEMS
DIAGNOSTICS
.......................8A-17
CHARGING SYSTEM; CHARGING
SYSTEM (XJ)
.....................8W-20-1
CHARGING SYSTEM; CHARGING
SYSTEM (XJ-RHD)
.................8W-20-1
CHARGING SYSTEM; CHARGING
SYSTEM (YJ)
.....................8W-20-1CHARGING SYSTEM INDICATOR LAMP;
INSTRUMENT CLUSTER (XJ).........8W-40-3
CHARGING SYSTEM SPECIFICATIONS....8A-23
CHARGING TIME TABLE, BATTERY........8A-8
CHART, MAIN BEARING FITTING......9-48,9-90
CHART, XJ PERFORMANCE
TEMPERATURE AND PRESSURE.........24-13
CHART, YJ PERFORMANCE
TEMPERATURE AND PRESSURE.........24-13
CHARTÐAX 15 MANUAL
TRANSMISSION, SELECTIVE SNAP
RING.............................21-334
CHARTS, BRAKELINE..................5-12
CHARTS, DIAGNOSIS GUIDES...........21-77
CHARTS, GEARTRAIN OPERATION AND
APPLICATION.......................21-169
CHARTS, INSPECTION AND DIAGNOSIS.....6-4
CHASSIS AND BODY COMPONENTS.......0-28
CHASSIS COMPONENT AND WHEEL
BEARING LUBRICANTS.................0-28
CHECK VALVE TEST, POWER BOOSTER.....5-9
CHECKING FLUID LEVEL AND
CONDITION........................21-182
CHECKS, PRELIMINARY.................7-5
CHIME/BUZZER MODULE; INTERIOR
LIGHTING (XJ)....................8W-44-2
CHIME/BUZZER MODULE; INTERIOR
LIGHTING (XJ-RHD)................8W-44-2
CHMSL LAMPS, STOP LAMPS; REAR
LIGHTING (XJ)....................8W-51-1
CHMSL LAMPS, STOP LAMPS; REAR
LIGHTING (XJ-RHD)................8W-51-1
CHMSL LAMPS, STOP LAMPS; REAR
LIGHTING (YJ)....................8W-51-1
(CHMSL)ÐXJ, CENTER HIGH MOUNTED
STOP LAMP.........................8L-12
(CHMSL)ÐYJ, CENTER HIGH MOUNTED
STOP LAMP.........................8L-28
CIGAR LIGHTER; HORN/CIGAR LIGHTER . . . 8E-1
CIGAR LIGHTER; HORN/CIGAR LIGHTER
(YJ).............................8W-41-1
CIGAR LIGHTER; INSTRUMENT CLUSTER
(XJ).............................8W-40-1
CIRCUIT IDENTIFICATION; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)...............................8W-1
CIRCUIT REMOVE/INSTALL, PRINTED....8E-19,
8E-40
CIRCUIT SENSEÐPCM INPUT, IGNITION . . 14-23
CIRCUIT VOLTAGE, OPEN...............8A-6
CLAMPS, FUEL TUBES/LINES/HOSES . 14-62,14-9
CLASSIFICATION OF LUBRICANTS.........0-2
CLASSIFICATIONS AND RATINGS,
BATTERY...........................8A-23
CLEANER, AIR.......................14-29
CLEANER ELEMENT, AIR; EMISSION
CONTROL SYSTEMS...................25-7
CLEANER ELEMENT, AIR; FUEL SYSTEM . . 14-59
CLEANER ELEMENT, AIR; LUBRICATION
AND MAINTENANCE...................0-18
CLEANER HOUSING, AIR...............14-58
CLEANING AND INSPECTION, CALIPER....5-50
CLEANING AND INSPECTION, GEAR......19-42
CLEANING AND INSPECTION,
TRANSMISSION CASE................21-125
CLEANING OF TIRES...................22-2
CLEANING/INSPECTION; FRONT
SUSPENSION AND AXLE
................2-37
CLEANING/INSPECTION; REAR
SUSPENSION AND AXLES
...............3-20
CLEANING/REVERSE FLUSHING,
COOLING SYSTEM
....................7-22
CLEARANCE AND RAMP ANGLE,
GROUND
............................0-11
CLEARANCE, AW-4 BUSHING AND
PISTON
...........................21-339
CLOCKSPRING
.......................19-51
CLUSTER AND GAUGE HOUSINGSÐYJ,
INSTRUMENT
......................23-151
CLUSTER ASSEMBLY REMOVE/INSTALL
. . 8E-17,
8E-35
CLUSTER BEZELÐXJ, INSTRUMENT
.....23-80
CLUSTER BEZELÐYJ, INSTRUMENT
....23-151
CLUSTER CONNECTORS (RHD)
.........8E-11
CLUSTER, GAUGE PACKAGE
.......8E-31,8E-43
CLUSTER GROUND; INSTRUMENT
CLUSTER (XJ)
.....................8W-40-3
4 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

CONTENTS; INSTRUMENT PANEL AND
GAUGESÐXJ........................8E-24
CONTENTS; LAMPS...................8L-19
CONTINUITY (LEFT POSITION), POWER
MIRROR SWITCH.....................8T-3
CONTINUITY, POWER SEAT SWITCH......8R-2
CONTINUITY (RIGHT POSITION), POWER
MIRROR SWITCH.....................8T-3
CONTINUITY TESTS, IGNITION SWITCH . . . 8D-30
CONTROL AND DISPLAY SYMBOLS,
INTERNATIONAL VEHICLE.............Intro.-5
CONTROL AND DISPLAY SYMBOLS,
VEHICLE.........................Intro.-10
CONTROL CABLES, VENT DOOR.........24-32
CONTROL DIAGNOSTIC TROUBLE CODE,
SPEED..............................8H-5
CONTROL, FUEL PUMP ELECTRICAL......14-5
CONTROL (IAC) MOTOR, IDLE AIR; FUEL
SYSTEM............................14-62
CONTROL (IAC) MOTOR, IDLE AIR;
FUEL/IGNITION (XJ)................8W-30-2
CONTROL (IAC) MOTOR, IDLE AIR;
FUEL/IGNITION (YJ)................8W-30-2
CONTROL (IAC) MOTOR, IDLE AIR;
FUEL/IGNITION (XJ-RHD)............8W-30-2
CONTROL (IAC) MOTORÐPCM OUTPUT,
IDLE AIR...........................14-27
CONTROL INFORMATION (VECI) LABEL,
VEHICLE EMISSION....................25-1
CONTROL MODULE (PCM) 60-WAY
CONNECTOR, POWERTRAIN............14-40
CONTROL MODULE (PCM),
POWERTRAIN; EMISSION CONTROL
SYSTEMS...........................25-7
CONTROL MODULE (PCM),
POWERTRAIN; FUEL SYSTEM......14-20,14-64
CONTROL MODULE (PCM),
POWERTRAIN; IGNITION SYSTEMS......8D-11,
8D-23,8D-5
CONTROL MODULE, POWERTRAIN . . . 8H-1,8H-7
CONTROL MODULE (TCM) SERVICE,
TRANSMISSION.....................21-183
CONTROL MODULE, TRANSMISSION;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
CONTROL MODULEÐ4.0L ENGINE ONLY,
TRANSMISSION; TRANSMISSION
CONTROLS (XJ)...................8W-31-1
CONTROL MOTOR TEST, IDLE AIR.......14-49
CONTROL PANEL LAMP, ACCESSORY
LAMP AND HEATER; INTERIOR
LIGHTING (YJ)....................8W-44-1
CONTROL REPLACEMENT, HEATER.......24-32
CONTROL REPLACEMENT, HEATER AND
A/C................................24-23
CONTROL SERVO REMOVE/INSTALL,
SPEED..............................8H-9
CONTROL SERVO, SPEED..........8H-1,8H-6
CONTROL SWITCH REMOVE/INSTALL,
SPEED..............................8H-9
CONTROL SWITCH, SPEED.........8H-1,8H-6
CONTROL SYSTEM, EMISSION...........0-20
CONTROL SYSTEM, EVAP
(EVAPORATION)......................25-4
CONTROL SYSTEM MAINTENANCE,
EMISSION............................0-4
CONTROL THERMOSTAT, TEMPERATURE . . 24-34
CONTROL, THERMOSTATIC.............24-16
CONTROL UNIT (ECU), ELECTRONIC......5-34
CONTROL UNIT (HCU), HYDRAULIC.......5-33
CONTROL UNIT, HYDRAULIC; ANTI-LOCK
BRAKES (XJ)......................8W-32-2
CONTROL UNIT, HYDRAULIC; ANTI-LOCK
BRAKES (XJ-RHD).................8W-32-2
CONTROL UNIT, HYDRAULIC; ANTI-LOCK
BRAKES (YJ)......................8W-32-2
CONTROL VALVE FITTING O-RING SEAL,
FLOW..............................19-14
CONTROL, VEHICLE SPEED; VEHICLE
SPEED CONTROL (XJ)..............8W-33-1
CONTROL, VEHICLE SPEED; VEHICLE
SPEED CONTROL (XJ-RHD)..........8W-33-1
CONTROLÐPCM INPUT, SPEED
.........14-25
CONTROLÐPCM OUTPUT, SPEED
.......14-29
CONTROLS AND COMPONENTS,
TRANSMISSION
......................21-67
CONTROLS, EMISSION
.................25-4
CONTROLSÐPCM INPUT, AIR
CONDITIONING (A/C)
..................14-21CONTROLSÐXJ VEHICLES, AIR
CONDITIONING......................24-15
CONTROLSÐYJ VEHICLES, AIR
CONDITIONING......................24-16
CONVERSION FORMULAS AND
EQUIVALENT VALUES...............Intro.-11
CONVERSION, METRIC..............Intro.-16
CONVERSION, METRIC AND ENGLISH/
SAE .............................Intro.-11
CONVERTER, CATALYTIC............11-1,11-4
CONVERTER CLUTCH RELAY TEST,
TORQUE............................14-48
CONVERTER CLUTCH RELAY, TORQUE....14-65
CONVERTER CLUTCH RELAYÐPCM
OUTPUT, TORQUE....................14-29
CONVERTER CLUTCH (TCC) SOLENOID
AND RELAY, TORQUE; FUEL/IGNITION
(XJ).............................8W-30-4
CONVERTER CLUTCH (TCC) SOLENOID
AND RELAY, TORQUE; TRANSMISSION
CONTROLS (YJ)...................8W-31-1
CONVERTER CLUTCH (TCC) SOLENOID
AND RELAYÐ2.5L ENGINE ONLY,
TORQUE; TRANSMISSION CONTROLS
(XJ).............................8W-31-1
CONVERTER DIAGNOSIS, TORQUE . 21-86,21-87,
21-88
CONVERTER HOUSING LEAK DIAGNOSIS . . 21-75
CONVERTER INSTALLATION,
TRANSMISSION.....................21-117
CONVERTER INSTALLATION,
TRANSMISSION AND TORQUE.........21-199
CONVERTER REMOVAL, TRANSMISSION . 21-115
CONVERTER REMOVAL, TRANSMISSION
AND TORQUE......................21-198
CONVERTER STALL TEST..............21-74
CONVERTER STALL TEST, TORQUE.....21-178
CONVERTER STATOR CLUTCH
INSPECTION, TORQUE................21-199
CONVERTER, TORQUE...........21-167,21-67
CONVERTERÐPUMP SEALÐDRIVE
PLATE SERVICE.....................21-116
CONVERTOR, CATALYTIC................25-1
COOLANT............................7-20
COOLANT RESERVE/OVERFLOW SYSTEM . . 7-24
COOLANT ROUTING, SYSTEM.............7-1
COOLANT TEMPERATURE GAUGE,
ENGINE; INSTRUMENT CLUSTER (XJ) . . 8W-40-1
COOLANT TEMPERATURE SENSOR.......25-7
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL SYSTEM................14-60
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL/IGNITION (XJ).........8W-30-3
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL/IGNITION (YJ).........8W-30-3
COOLANT TEMPERATURE SENSOR,
ENGINE; IGNITION SYSTEMS.......8D-19,8D-5
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL/IGNITION (XJ-RHD).....8W-30-3
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; FUEL SYSTEM................14-46
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; IGNITION SYSTEMS............8D-9
COOLANT TEMPERATURE SENSORÐ
PCM INPUT, ENGINE
..................14-23
COOLANT TEMPERATURE WARNING
LAMP, ENGINE; INSTRUMENT
CLUSTER (XJ)
.....................8W-40-1
COOLANT TEMPERATURE WARNING
LAMP, ENGINE; INSTRUMENT
CLUSTER (XJ-RHD)
................8W-40-1
COOLER FLOW TESTING,
TRANSMISSION
.....................21-113
COOLER LINE AND FITTING SERVICE,
TRANSMISSION
.....................21-111
COOLER LINE FITTINGS, TRANSMISSION
. 21-197
COOLER REVERSE FLUSHING,
TRANSMISSION
.....................21-114
COOLER SERVICE, TRANSMISSION
.....21-196
COOLERS, TRANSMISSION OIL
..........7-36
COOLING FANÐXJ MODELS WITH 4.0L
6-CYLINDER ENGINE, AUXILIARY
ELECTRIC
...........................7-35
COOLING SYSTEM; COOLING SYSTEM
......7-1
COOLING SYSTEM; HEATING AND AIR
CONDITIONING
......................24-10
COOLING SYSTEM CAPACITIES
..........7-45COOLING SYSTEM CLEANING/REVERSE
FLUSHING...........................7-22
COOLING SYSTEM COMPONENTS.........7-1
COOLING SYSTEM DIAGNOSIS............7-6
COOLING SYSTEM, DRAINING...........7-21
COOLING SYSTEM, ENGINE.............0-18
COOLING SYSTEM FANS................7-32
COOLING SYSTEM FOR LEAKS, TESTING . . . 7-22
COOLING SYSTEM HOSES..............7-32
COOLING SYSTEM, REFILLING...........7-21
CORE AND HOUSING, HEATER..........24-33
CORE, HEATER......................24-26
COURTESY LAMPS AND DOME LAMP,
CARGO LAMP; INTERIOR LIGHTING
(XJ).............................8W-44-1
COURTESY LAMPS AND DOME LAMPS;
INTERIOR LIGHTING (YJ)............8W-44-1
COURTESY LAMPS, READING...........8C-1
COVER AND DISC INSTALLATION,
CLUTCH.............................6-10
COVER AND DISC REMOVAL, CLUTCH.....6-10
COVER AND DISC RUNOUT, CLUTCH.......6-3
COVER AND FRAMEÐXJ, BUCKET
SEATBACK..........................23-81
COVER, ENGINE CYLINDER HEAD....9-22,9-64
COVER, FRAME CROSSMEMBER........13-16
COVER OIL SEAL REPLACEMENT,
TIMING CASE....................9-30,9-73
COVER REPLACEMENT, PITMAN SHAFT
AND SIDE..........................19-28
COVER, TIMING CASE..............9-31,9-72
COVERÐXJ, BUCKET SEAT CUSHION....23-81
COVERÐXJ, PARKING BRAKE HANDLE . . . 23-94
COVERÐXJ, REAR SEAT CUSHION......23-82
COVERÐXJ, REAR SEATBACK..........23-84
COVERSÐXJ, B/C-PILLAR AND
LIFTGATE PILLAR TRIM...............23-88
COWL GRILLE AND SCREENÐXJ........23-12
COWL GRILLE AND SCREENÐYJ.......23-109
COWL WEATHERSTRIP SEAL/
CROSSMEMBER AIR DEFLECTORÐXJ....23-11
COWL WEATHERSTRIP SEALÐYJ......23-109
CRANKCASE VENTILATION SYSTEM;
EMISSION CONTROL SYSTEMS..........25-5
CRANKCASE VENTILATION SYSTEM;
LUBRICATION AND MAINTENANCE........0-19
CRANKING SPECIFICATIONS, 2.5L
STARTING SYSTEM COLD..............8A-23
CRANKING SPECIFICATIONS, 4.0L
STARTING SYSTEM COLD..............8A-23
CRANKSHAFT MAIN BEARINGS......9-45,9-87
CRANKSHAFT POSITION SENSOR; FUEL
SYSTEM............................14-60
CRANKSHAFT POSITION SENSOR;
FUEL/IGNITION (XJ)................8W-30-3
CRANKSHAFT POSITION SENSOR;
FUEL/IGNITION (YJ)................8W-30-3
CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS..............8D-17,8D-3
CRANKSHAFT POSITION SENSOR;
FUEL/IGNITION (XJ-RHD)............8W-30-3
CRANKSHAFT POSITION SENSOR TEST;
FUEL SYSTEM.......................14-47
CRANKSHAFT POSITION SENSOR TEST;
IGNITION SYSTEMS...................8D-7
CRANKSHAFT POSITION SENSORÐPCM
INPUT.............................14-22
CROSSMEMBER COVER, FRAME........13-16
CROSSMEMBERÐXJ, RADIATOR
SUPPORT...........................23-6
CUSHION AND COVERÐXJ, BUCKET
SEAT ..............................23-81
CUSHION COVERÐXJ, REAR SEAT......23-82
CUSHIONÐXJ, REAR SEAT.............23-82
CUT-OFF SWITCH, LOW-PRESSURE
HIGH-PRESSURE................24-15,24-16
CYCLING CLUTCH SWITCH, FIN
SENSING......................24-15,24-31
CYLINDER AND COMBINATION VALVE
INSTALLATION (WITH ABS), MASTER.....5-20
CYLINDER AND COMBINATION VALVE
REMOVAL (WITH ABS), MASTER.........5-17
CYLINDER BENCH BLEEDING, MASTER
....5-21
CYLINDER BLOCK
.................9-49,9-91
CYLINDER BORES, HONING
..............9-2
CYLINDER, CLUTCH MASTER
............0-22
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST
........................9-6
6 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

ENTRY MODULE REMOVE/INSTALL,
KEYLESS...........................8P-10
ENTRY RECEIVER, KEYLESS.............8C-1
ENTRY RECEIVERÐXJ, KEYLESS........23-93
ENTRY TRANSMITTER, KEYLESS . 8P-1,8P-7,8P-8
EQUIPMENT, REFRIGERANT.............24-7
EQUIVALENT VALUES, CONVERSION
FORMULAS.......................Intro.-11
EVACUATING REFRIGERANT SYSTEM.....24-11
EVAP CANISTER..................25-4,25-7
EVAP (EVAPORATION) CONTROL
SYSTEM............................25-4
EVAPORATIVE HOUSING
COMPONENTSÐYJ....................24-6
EVAPORATOR AND HOUSING...........24-35
EVAPORATOR COIL...................24-30
EVAPORATOR/BLOWER HOUSING........24-29
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM............................25-1
EXHAUST GRILLEÐXJ, AIR............23-25
EXHAUST HEAT SHIELDS...............11-1
EXHAUST MANIFOLDÐ2.5L ENGINE,
ENGINE.............................11-7
EXHAUST MANIFOLDÐ4.0L ENGINE,
ENGINE.............................11-7
EXHAUST PIPEÐXJ VEHICLES...........11-3
EXHAUST PIPEÐYJ VEHICLES...........11-4
EXHAUST SYSTEM; EXHAUST SYSTEM
AND INTAKE MANIFOLD................11-1
EXHAUST SYSTEM; LUBRICATION AND
MAINTENANCE.......................0-21
EXHAUST SYSTEM DIAGNOSIS..........11-2
EXHAUST TAILPIPEÐXJ VEHICLES,
MUFFLER............................11-5
EXHAUST TAILPIPEÐYJ VEHICLES,
MUFFLER............................11-6
EXPANSION VALVE..............24-31,24-35
EXTENDED IDLE SWITCH; FUEL/
IGNITION (XJ).....................8W-30-5
EXTENDED IDLE SWITCH TEST..........14-48
EXTENDED IDLE SWITCHÐPCM INPUT . . . 14-23
EXTENSIONÐXJ, QUARTER TRIM PANEL . 23-87
EXTERIOR COMPONENTS.........23-104,23-3
EXTERIOR LAMPSÐXJ................8L-18
EXTERIOR LAMPSÐYJ................8L-32
EXTERIOR MOLDINGSÐXJ, DOOR
WINDOW...........................23-54
EXTERIOR NAMEPLATES (ADHESIVE-
BACKED)ÐYJ......................23-120
EXTERIOR NAMEPLATESÐXJ...........23-26
EXTERNAL HANDLEÐXJ, DOOR.........23-48
EXTERNAL MIRRORSÐXJ.............23-27
EXTERNAL RELEASE HANDLEÐYJ,
FULL-METAL DOOR LATCH............23-140
EXTERNAL SPARE/WHEEL TIRE
CARRIERÐYJ......................23-133
(EXTERNAL)ÐYJ, HALF METAL DOOR
MIRROR..........................23-121
EYE BUSHING REPLACEMENT, LEAF
SPRING; FRONT SUSPENSION AND
AXLE...............................2-17
EYE BUSHING REPLACEMENT, LEAF
SPRING; REAR SUSPENSION AND
AXLES............................3-5,3-7
FAN RELAY AND MOTOR, RADIATOR;
AIR CONDITIONING/HEATER (XJ)......8W-42-2
FAN RELAY AND MOTOR, RADIATOR;
AIR CONDITIONING/HEATER (XJ-RHD) . . 8W-42-2
FAN RELAYÐPCM OUTPUT, RADIATOR . . . 14-28
FANÐXJ MODELS WITH 4.0L
6-CYLINDER ENGINE, AUXILIARY
ELECTRIC COOLING...................7-35
FANS, COOLING SYSTEM...............7-32
FEED, BATTERY; FUEL/IGNITION (XJ) . . . 8W-30-1
FEED, BATTERY; FUEL/IGNITION (YJ) . . . 8W-30-2
FEED, BATTERY; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
FEED, IGNITION; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
FENDER FLAREÐYJ.................23-114
FENDER INNER SPLASH SHIELDSÐYJ . . 23-116
FENDER SPLASH APRONSÐYJ........23-115
FENDERÐXJ, FRONT
.................23-14
FENDERSÐYJ
......................23-110
FIELDÐPCM OUTPUT, GENERATOR
......14-27
FILL LEVEL, TRANSFER CASE
LUBRICANT
........................21-284
FILLER DOOR BUMPERSÐXJ, FUEL
.....23-27FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES, FUEL......................13-4
FILLER NOZZLE/TUBEÐXJ, FUEL........23-26
FILLER PROTECTOR/NOZZLEÐYJ, FUEL . 23-121
FILLER TUBE CAP, FUEL TANK;
EMISSION CONTROL SYSTEMS......25-4,25-7
FILLER TUBE CAP, FUEL TANK; FUEL
SYSTEM............................14-13
FILLER TUBE, NO-LEAD FUEL TANK......14-13
FILTER DRIERÐ2.5L ENGINES,
CONDENSER........................24-27
FILTER DRIERÐ4.0L ENGINES..........24-28
FILTER, ENGINE OIL...................0-17
FILTER, FUEL; FUEL SYSTEM.......14-60,14-9
FILTER, FUEL; LUBRICATION AND
MAINTENANCE.......................0-19
FILTER REPLACEMENT, ENGINE OIL
CHANGE............................0-16
FILTER REPLACEMENT, FLUID..........21-99
FILTER REPLACEMENT, OIL............21-103
FIN SENSING CYCLING CLUTCH SWITCH . 24-15,
24-31
FINAL ASSEMBLY; FRONT SUSPENSION
AND AXLE...........................2-46
FINAL ASSEMBLY; REAR SUSPENSION
AND AXLES..........................3-29
FIRING ORDERÐ2.5L 4-CYLINDER
ENGINE, ENGINE.....................8D-32
FIRING ORDERÐ4.0L 6-CYLINDER
ENGINE, ENGINE.....................8D-32
FIRST-REVERSE BRAKE PISTON AND
TRANSMISSION CASE OVERHAUL......21-247
FIRST/SECOND/THIRD/REVERSE
COMPONENTS......................21-168
FITTING CHART, CONNECTING ROD
BEARING........................9-41,9-83
FITTING CHART, MAIN BEARING......9-48,9-90
FITTING O-RING SEAL, FLOW CONTROL
VALVE .............................19-14
FITTING SERVICE, TRANSMISSION
COOLER LINE......................21-111
FITTINGS, TRANSMISSION COOLER LINE . 21-197
FLAREÐYJ, FENDER.................23-114
FLARES AND LINERSÐXJ, REAR
WHEELHOUSE.......................23-19
FLASHER, COMBINATION; TURN
SIGNALS (XJ).....................8W-52-1
FLASHERS, HAZARD; TURN SIGNALS
(XJ).............................8W-52-1
FLASHERS, HAZARD; TURN SIGNALS
(XJ-RHD).........................8W-52-1
FLASHERS, HAZARD; TURN SIGNALS
(YJ).............................8W-52-1
FLOOR BRACKETSÐXJ, SPARE
TIRE/WHEEL HOLDDOWN..............23-98
FLOOR CONSOLEÐXJ, FULL...........23-95
FLOOR CONSOLESÐYJ...............23-155
FLOOR MATSÐXJ, CARPETS...........23-99
FLOOR SHIFTÐXJ, MINI-CONSOLE WITH . 23-94
FLOW CONTROL VALVE FITTING O-RING
SEAL..............................19-14
FLOW TESTING, TRANSMISSION
COOLER...........................21-113
FLUID AND FILTER REPLACEMENT.......21-99
FLUID CAPACITIES.....................0-3
FLUID, CLUTCH LINKAGE................6-1
FLUID CONTAMINATION, BRAKE.......5-10,5-7
FLUID LEVEL AND CONDITION,
CHECKING.........................21-182
FLUID LEVEL, BRAKE..................5-10
FLUID LEVEL CHECK.............21-70,21-99
FLUID LEVEL, CLUTCH.................6-14
FLUID, RECOMMENDED BRAKE..........5-10
FLUID WARNING LAMP, LOW WASHER;
INSTRUMENT CLUSTER (XJ).........8W-40-2
FLUID WARNING LAMP, LOW WASHER;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
FLUID/FILTER CHANGE, REFILLING
AFTER OVERHAUL OR..........21-100,21-182
FLUID/LUBRICANTS/CLEANING
SOLVENTS, BRAKE
.....................5-2
FLUIDÐBRAKE BLEEDINGÐ
BRAKELINES AND HOSES, BRAKE
........5-10
FLUSHING, COOLING SYSTEM
CLEANING/REVERSE
...................7-22
FLUSHING, TRANSMISSION COOLER
REVERSE
..........................21-114
FLYWHEEL RUNOUT
....................6-3FLYWHEEL SERVICE...................6-16
FOG LAMP DIAGNOSIS............8L-21,8L-3
FOG LAMP REPLACEMENTÐXJ..........8L-9
FOG LAMP REPLACEMENTÐYJ.........8L-25
FOG LAMP SWITCH REPLACEMENTÐXJ . . 8L-10
FOG LAMP SWITCH REPLACEMENTÐYJ . . 8L-26
FOG LAMPS; FRONT LIGHTING (XJ) . . . 8W-50-1
FOG LAMPS; FRONT LIGHTING (XJ-RHD) . 8W-50-2
FOG LAMPS; FRONT LIGHTING (YJ) . . . 8W-50-1
FOG LAMPSÐXJ......................8L-7
FOG LAMPSÐYJ.....................8L-23
FORM-IN-PLACE GASKETS...............9-1
FORMULAS AND EQUIVALENT VALUES,
CONVERSION.....................Intro.-11
FORWARD CLUTCH OVERHAUL........21-232
FOURTH GEAR OVERDRIVE
COMPONENTS......................21-167
FOUR-WHEEL DRIVE (4WD) SWITCH;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
FOUR-WHEEL DRIVE (4WD) SWITCH;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
FOUR-WHEEL-DRIVE VEHICLE TOWING....0-12
FRAME.........................13-10,13-1
FRAME CROSSMEMBER COVER.........13-16
FRAME DIMENSIONS.............13-13,13-1
FRAME GLASS CHANNEL
REPLACEMENTÐYJ, DOOR...........23-142
FRAME REPAIRS......................13-13
FRAME STRAIGHTENING...............13-13
FRAME WEATHERSTRIP SEALÐYJ,
WINDSHIELD.......................23-146
FRAMEÐXJ, BUCKET SEATBACK COVER . . 23-81
FRAMEÐYJ, WINDSHIELD............23-145
FREQUENCY INTERFERENCE, RADIO......8F-5
FRESH AIR DOOR VACUUM MOTOR......24-34
FRESH AIR INTAKE DUCT..............24-34
FRONT AND REAR AXLES...............0-24
FRONT AXLE, MODEL 30...............2-49
FRONT BUCKET SEATSÐXJ............23-81
FRONT BUMPER.................13-16,13-5
FRONT CABLE REPLACEMENT (YJ),
PARKING BRAKE......................5-67
FRONT CARPET/MATÐXJ..............23-99
FRONT CLUTCH OVERHAUL...........21-134
FRONT DOOR SPACER BLOCKSÐTWO-
DOOR VEHICLES.....................23-53
FRONT DOOR WINDOW GLASS
REGULATORÐXJ....................23-42
FRONT DOOR WINDOW GLASSÐXJ.....23-43
FRONT DRIVE AXLE....................2-3
FRONT FENDERÐXJ..................23-14
FRONT INNER SCUFF PLATE/COWL SIDE
TRIM PANELÐXJ....................23-86
FRONT PARK/TURN SIGNAL LAMP BULB
REPLACEMENTÐXJ...................8L-9
FRONT PARK/TURN SIGNAL LAMP BULB
REPLACEMENTÐYJ..................8L-25
FRONT PLANETARY GEAR OVERHAUL . . . 21-237
FRONT SERVO AND BAND OVERHAUL . . . 21-146
FRONT SHOULDER BELT/BUCKLEÐXJ....23-90
FRONT SHOULDER BELTSÐYJ.........23-154
FRONT SKID PLATE
....................13-1
FRONT SUSPENSION
...................2-1
FRONT SUSPENSION COMPONENTS, XJ
. . . 2-49
FRONT SUSPENSION COMPONENTS, YJ
. . . 2-49
FRONT SUSPENSION, XJ
...............2-11
FRONT SUSPENSION, YJ
...............2-15
FRONT TOW HOOKS
...................13-7
FRONT WHEEL ALIGNMENT
..............2-5
FRONT WHEEL BEARINGS
..............0-28
FRONT WHEEL SENSOR INSTALLATION
....5-38
FRONT WHEEL SENSOR REMOVAL
.......5-38
FUEL DELIVERY SYSTEM
...............14-3
FUEL FILLER DOOR BUMPERSÐXJ
......23-27
FUEL FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES
...........................13-4
FUEL FILLER NOZZLE/TUBEÐXJ
........23-26
FUEL FILLER PROTECTOR/NOZZLEÐYJ
. . 23-121
FUEL FILTER; FUEL SYSTEM
........14-60,14-9
FUEL FILTER; LUBRICATION AND
MAINTENANCE
.......................0-19
FUEL GAUGE; INSTRUMENT CLUSTER
(XJ)
.............................8W-40-1
FUEL GAUGE; INSTRUMENT CLUSTER
(XJ-RHD)
.........................8W-40-1
FUEL GAUGE SENDING UNIT
...........14-16
10 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

GENERAL INFORMATION; POWER LOCKS . . 8P-1
GENERAL INFORMATION; POWER
MIRRORS...........................8T-1
GENERAL INFORMATION; POWER SEATS . . 8R-1
GENERAL INFORMATION; POWER
WINDOWS...........................8S-1
GENERAL INFORMATION; PROPELLER
SHAFTS.............................16-1
GENERAL INFORMATION; REAR
SUSPENSION AND AXLES........3-13,3-1,3-9
GENERAL INFORMATION; REAR
WINDOW DEFOGGER..................8N-1
GENERAL INFORMATION; RESTRAINT
SYSTEMS...........................8M-1
GENERAL INFORMATION; SPLICE
INFORMATION (XJ).................8W-70-1
GENERAL INFORMATION; SPLICE
INFORMATION (XJ-RHD)............8W-70-1
GENERAL INFORMATION; SPLICE
INFORMATION (YJ).................8W-70-1
GENERAL INFORMATION; SPLICE
LOCATIONS (XJ)...................8W-95-1
GENERAL INFORMATION; SPLICE
LOCATIONS (XJ-RHD)...............8W-95-1
GENERAL INFORMATION; SPLICE
LOCATIONS (YJ)...................8W-95-1
GENERAL INFORMATION; STEERING . 19-48,19-1
GENERAL INFORMATION;
TRANSMISSION AND TRANSFER CASE . . 21-165,
21-283,21-307,21-33,21-67,21-70,21-1
GENERAL INFORMATION; TURN SIGNAL
AND HAZARD WARNING SYSTEMS.......8J-1
GENERAL INFORMATION; VEHICLE
SPEED CONTROL SYSTEM..............8H-1
GENERAL INFORMATION; WHEELS AND
TIRES..........................22-1,22-6
GENERAL INFORMATION - XJ............8K-1
GENERAL INFORMATION - YJ...........8K-10
GENERAL SERVICE INFORMATION; BODY
COMPONENTSÐXJ VEHICLES.........23-102
GENERAL SERVICE INFORMATION;
BRAKES.........................5-15,5-60
GENERAL SERVICEÐXJ, STEERING
COLUMN...........................19-47
GENERAL SPECIFICATIONS, 30RH/32RH . 21-335
GENERAL SPECIFICATIONS, AW-4......21-337
GENERATOR.........................8B-6
GENERATOR DIAGNOSTIC TROUBLE
CODE..............................8A-22
GENERATOR FIELDÐPCM OUTPUT......14-27
GENERATOR LAMPÐPCM OUTPUT......14-27
GENERATOR RATINGS................8A-23
GENERATOR REMOVE/INSTALLÐLEFT-
HAND DRIVE.........................8B-6
GENERATOR REMOVE/INSTALLÐRIGHT-
HAND DRIVE.........................8B-7
GENERATOR SPECIFICATIONS...........8B-8
GENERATOR SPLASH SHIELD...........13-13
GLASS AND DOOR OPENING
WEATHERSTRIP SEALSÐXJ, DOOR
WINDOW...........................23-55
GLASS CHANNEL REPLACEMENTÐYJ,
DOOR FRAME......................23-142
GLASS GRID, REAR WINDOW.......8N-1,8N-2
GLASS GRID REPAIRS, REAR WINDOW . . . 8N-3
GLASS REGULATOR HANDLEÐYJ,
FULL-METAL DOOR WINDOW..........23-136
GLASS REGULATORÐXJ, FRONT DOOR
WINDOW...........................23-42
GLASS REGULATORÐXJ, REAR DOOR
WINDOW...........................23-44
GLASS REGULATORÐYJ, FULL-METAL
DOOR WINDOW....................23-138
GLASS REPLACEMENTÐXJ,
WINDSHIELD........................23-69
GLASS, STATIONARY.................23-144
GLASS, STATIONARY WINDOW..........23-66
GLASS WATER LEAK DETECTION AND
REPAIRÐXJ, STATIONARY.............23-76
GLASS WATER LEAK DETECTION AND
REPAIRÐYJ, STATIONARY............23-150
GLASS WEATHERSTRIP SEAL
REPLACEMENTÐYJ, LIFTGATE
.........23-125
GLASSÐXJ, FRONT DOOR WINDOW
.....23-43
GLASSÐXJ, LIFTGATE WINDOW
........23-74
GLASSÐXJ, REAR DOOR STATIONARY
WINDOW
...........................23-46
GLASSÐXJ, REAR DOOR WINDOW
......23-45GLASSÐXJ, REAR QUARTER VENT
WINDOW...........................23-73
GLASSÐYJ, FULL-METAL DOOR VENT
WINDOW..........................23-137
GLASSÐYJ, FULL-METAL DOOR
WINDOW..........................23-139
GLASSÐYJ, HARD TOP LIFTGATE......23-124
GLASSÐYJ, HARD TOP QUARTER
WINDOW..........................23-149
GLASSÐYJ, WINDSHIELD............23-146
GLASS/REAR QUARTER PLASTIC
INSERTÐXJ, REAR QUARTER
WINDOW...........................23-73
GLOVE BOX LAMP; INTERIOR LIGHTING
(XJ).............................8W-44-1
GLOVE BOX LAMP; INTERIOR LIGHTING
(XJ-RHD).........................8W-44-1
GLOVE BOXÐYJ....................23-152
(GOP)ÐXJ, GRILLE AND GRILLE
OPENING PANEL......................23-3
GOVERNOR AND PARK GEAR OVERHAUL . 21-127
GOVERNOR AND PARK GEAR SERVICE . . 21-105
GRAB, REAR BRAKE....................5-7
GRID, REAR WINDOW GLASS.......8N-1,8N-2
GRID REPAIRS, REAR WINDOW GLASS . . . 8N-3
GRILLE AND GRILLE OPENING PANEL
(GOP)ÐXJ...........................23-3
GRILLE AND SCREENÐXJ, COWL.......23-12
GRILLE AND SCREENÐYJ, COWL......23-109
GRILLE APPLIQUEÐYJ, RADIATOR.....23-104
GRILLE OPENING PANEL (GOP)ÐXJ,
GRILLE.............................23-3
GRILLEÐXJ, AIR EXHAUST............23-25
GROUND CLEARANCE AND RAMP
ANGLE..............................0-11
GROUND, CLUSTER; INSTRUMENT
CLUSTER (XJ).....................8W-40-3
GROUND, CLUSTER; INSTRUMENT
CLUSTER (XJ-RHD)................8W-40-2
GROUND, POWER....................14-24
GROUND, POWER (DEVICE); FUEL/
IGNITION (XJ).....................8W-30-5
GROUND, POWER (DEVICE); FUEL/
IGNITION (YJ).....................8W-30-5
GROUND, POWER (DEVICE); FUEL/
IGNITION (XJ-RHD)................8W-30-5
GROUP, HOW TO USE THIS; WIRING
DIAGRAMS (XJ)......................8W-1
GROUP, HOW TO USE THIS; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
GROUP, HOW TO USE THIS; WIRING
DIAGRAMS (YJ)......................8W-1
GUARD/EDGE PROTECTOR STRIPÐXJ,
DOOR EDGE........................23-54
GUARDÐXJ, BRUSH...................23-3
GUIDES AND CHARTS, DIAGNOSIS......21-77
HALF METAL DOOR MIRROR
(EXTERNAL)ÐYJ....................23-121
HALF-METAL DOOR LATCH STRIKERÐ
YJ ...............................23-135
HALF-METAL SOFT TOP DOORÐYJ.....23-134
HAND DRIVE, AUTOMATIC BELT
TENSIONERÐXJ MODELS WITH
RIGHT..............................7-42
HAND DRIVE, BELT SERVICEÐEXCEPT
RIGHT..............................7-40
HAND DRIVE, BELT SERVICEÐXJ
MODELS WITH RIGHT..................7-42
HAND DRIVE (RHD), BELT TENSIONÐ
EXCEPT RIGHT.......................7-38
HAND DRIVE (RHD), BELT TENSIONÐ
RIGHT..............................7-38
HAND DRIVE (RHD) MODELS, BELT
TENSIONÐEXCEPT RIGHT..............7-45
HAND DRIVE VEHICLES, RIGHT..........23-1
HANDLE COVERÐXJ, PARKING BRAKE . . . 23-94
HANDLEÐXJ, ASSIST.................23-89
HANDLEÐXJ, DOOR EXTERNAL.........23-48
HANDLEÐYJ, FULL-METAL DOOR
ASSIST
...........................23-136
HANDLEÐYJ, FULL-METAL DOOR LATCH
EXTERNAL RELEASE
.................23-140
HANDLEÐYJ, FULL-METAL DOOR LATCH
INSIDE RELEASE AND LOCK
...........23-137
HANDLEÐYJ, FULL-METAL DOOR
WINDOW GLASS REGULATOR
.........23-136
HANDLEÐYJ, TAILGATE LATCH AND
RELEASE
..........................23-122HANDLING, AIRBAG MODULE...........8M-2
HARD PEDAL OR HIGH PEDAL EFFORT.....5-6
HARD TOP LIFTGATE GLASSÐYJ.......23-124
HARD TOP QUARTER WINDOW
GLASSÐYJ........................23-149
HARD TOP REPAIRÐYJ..............23-127
HARD TOP ROOF VENTÐYJ...........23-127
HARD TOPÐYJ.....................23-126
HARDTOP DOME/CARGO LAMP BULB
REPLACEMENTÐYJ VEHICLES..........8L-31
HAS A MISS, INJECTOR DIAGNOSISÐ
VEHICLE RUNS ROUGH AND/OR........14-52
HAZARD FLASHERS; TURN SIGNALS
(XJ).............................8W-52-1
HAZARD FLASHERS; TURN SIGNALS
(XJ-RHD).........................8W-52-1
HAZARD FLASHERS; TURN SIGNALS
(YJ).............................8W-52-1
HAZARD WARNING SYSTEM.............8J-1
HAZARD WARNING SYSTEM - YJ.........8J-4
HCU DIAGNOSIS, ANTILOCK ECU..........5-3
HCU INSTALLATION (XJ)................5-43
HCU INSTALLATION (YJ)................5-44
HCU OPERATION......................5-36
HCU REMOVAL (XJ)...................5-41
HCU REMOVAL (YJ)...................5-44
HEAD COVER, ENGINE CYLINDER....9-22,9-64
HEAD, ENGINE CYLINDER...........9-25,9-67
HEAD GASKET FAILURE DIAGNOSIS,
ENGINE CYLINDER.....................9-5
HEAD NOT REMOVED, VALVE
COMPONENT REPLACEÐCYLINDER . . . 9-23,9-65
HEADLAMP ALIGNMENT
PREPARATIONÐXJ....................8L-6
HEADLAMP ALIGNMENT
PREPARATIONÐYJ...................8L-22
HEADLAMP ALIGNMENTÐXJ............8L-6
HEADLAMP ALIGNMENTÐYJ...........8L-22
HEADLAMP BULB REPLACEMENTÐXJ.....8L-7
HEADLAMP BULB REPLACEMENTÐYJ....8L-23
HEADLAMP DELAY FUNCTION TROUBLE
DIAGNOSISÐXJ.....................8L-14
HEADLAMP DELAY MODULE; FRONT
LIGHTING (XJ)....................8W-50-2
HEADLAMP DELAY MODULE; FRONT
LIGHTING (XJ-RHD)................8W-50-1
HEADLAMP DELAY MODULE
REPLACEMENTÐXJ..................8L-14
HEADLAMP DELAY MODULEÐXJ,
SENTINEL..........................8L-14
HEADLAMP DIAGNOSIS...........8L-20,8L-2
HEADLAMP DIMMER SWITCH
REPLACEMENTÐYJ..................8L-26
HEADLAMP OR PANEL DIMMER SWITCH
REMOVE/INSTALL....................8E-42
HEADLAMP RELAY; FRONT LIGHTING
(XJ-RHD).........................8W-50-1
HEADLAMP SWITCH REMOVE/INSTALL . . . 8E-19
HEADLAMP SWITCH (XJ ONLY)......8U-1,8U-3
HEADLAMP SWITCHÐXJ..............8L-10
HEADLAMP SWITCHÐYJ..............8L-26
HEADLAMP/FOG LAMP ADJUSTMENT
USING ALIGNMENT SCREENÐXJ.........8L-7
HEADLAMP/FOG LAMP ADJUSTMENT
USING ALIGNMENT SCREENÐYJ........8L-23
HEADLAMPS; FRONT LIGHTING (XJ) . . . 8W-50-1
HEADLAMPS; FRONT LIGHTING
(XJ-RHD).........................8W-50-1
HEADLAMPS; FRONT LIGHTING (YJ) . . . 8W-50-1
HEADLAMPS; LUBRICATION AND
MAINTENANCE.......................0-33
HEADLINERÐXJ.....................23-92
HEAT SHIELDS......................14-13
HEAT SHIELDS, EXHAUST...............11-1
HEATED OXYGEN SENSOR; FUEL/
IGNITION (XJ).....................8W-30-3
HEATED OXYGEN SENSOR; FUEL/
IGNITION (YJ).....................8W-30-3
HEATED OXYGEN SENSOR; FUEL/
IGNITION (XJ-RHD)
................8W-30-3
HEATED REAR WINDOW; HEATED REAR
WINDOW (XJ)
.....................8W-48-1
HEATED REAR WINDOW; HEATED REAR
WINDOW (XJ-RHD)
.................8W-48-1
HEATED REAR WINDOW; HEATED REAR
WINDOW (YJ)
.....................8W-48-1
HEATER; AIR CONDITIONING/HEATER
(YJ)
.............................8W-42-1
12 INDEXJ
Description Group-Page Description Group-Page Description Group-Page