1995 GMC SIERRA engine oil

50,000 Miles (80 000 km)
0
0
Change engine oil and filter (or every 3 months, whichever occurs
first). AII Emissiou Cor1trd Senicv.
Lubricate the front suspension, king pin bushings. steering linkage,
transmission shift linkage, transfer case shift linkage. parking brake
cable guides, rear driveline center splines, front axle propshaft splines,
brake pedal springs and clutch pedal springs.
Ball joints and king pin
bushings should not be lubricated unless their temperature is
10" F
(- 12" C), or higher. When weather is cold, let the ball -joints and king
pin bushings warm up before lubrication or they could be damaged.
Perform each of the listed lubrication service items at this mileage
interval (or every
12 months, whichever occurs first).
Change automatic transmission fluid and filter
if the vehicle is mainly
driven under one or more
of these conditions:
0
0
a
0
In heavy city traffic where the outside temperature regularly
reaches
90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such
as found in taxi, police or delivery service. If you do
not use your vehicle under any
of these conditions, the fluid
and filter do not require changing.
Manual transmission fluid
doesn't require change.
Inspect shields and underhood insulation for damage or looseness.
Adjust or replace as required.
This is a Noise Emission Control
Service. Applicable only to vehicles sold in the United States.
Check the air intake system installation to assure that gaskets are
properly sealed and that all hose connections, fasteners and other
components are tight.
Also check to be sure that the air cleaner housing
is properly seated, the cover fits tightly and the wing nuts are tight.
Tighten connections and fasteners or replace damaged parts as
necessary.
This is a Noise Emission Control Service. Applicable only
to vehicles sold in the United States.
If your engine has a thermostatically controlled cooling Fan, inspect all
hoses and ducts for proper hook-up (or every
12 months. whichever
occurs first). Be sure the valve works properly.
This is a Noise
Emission Control Service. Applicable only to vehicles sold in t\
he
United States.
7-89
ProCarManuals.com

Maintenance Schedule II - Diesel Engines I-
(Continued)
0 Check rear/fi-ont axle fluid level and add fluid as needed. Check
constant velocity joints and axle seals for leaking.
‘!”:’
DATE
SERVICED BY: ACTUAL MILEAGE
r
55,000 Miles (88 000 km)
0 Change engine oil and filter (or every 3 months, whichever occurs
first).
An Emission Control Sen7ic.e.
0 Lubricate the front suspension, king pin bushings, steering linkage,
transmission shift linkage, transfer case shift linkage, parking brake
cable guides, rear driveline center splines, front axle propshaft splines,
brake pedal springs and clutch pedal springs. Ball joints and king pin
bushings should not be lubricated unless their temperature is
10” F
(-12” C), or higher. When weather is cold, let the ball joints and king
pin bushings warm up before lubrication or they could be damaged.
Perform each of the listed lubrication service items at this mileage
interval (or every
I2 months, whichever occurs first).
0 Rotate tires. See “Tire Inspection and Rotation’‘ in the Index for proper
rotation pattern and additional information. See “Tires”
in the Index.
0 Check rear/front axle fluid level and add i-luid as needed. Check
constant velocity joints and axle seals for leaking.
-I--’- .:. +
DATE I ACTUALMILEAGE I SERVICED BY:
~~~
7-90
ProCarManuals.com

60,000 Miles (100 000 km)
o
r
0
0
0
0
E
Change engine oil and filter (or every 3 months, whichever occurs
first).
An Emissim~ Control Ser~~ice.
Lubricate the front suspension, king pin bushings, steering linkage,
transmission shift linkage. transfer case shift linkage. parking brake
cable guides. rear driveline center splines, front axle propshaft splines,
brake pedal springs and clutch pedal springs. Ball joints and king pin
bushings should
not be lubricated unless their temperature is 10" F
(-12" C). or higher. When weather is cold, let the ball joints and king
pin bushings warm up before lubrication or they could be damaged.
Perform each
of the listed lubrication service items at this mileage
interval (or every 12 months, whichever occurs first).
For vehicles equipped with a 5-speed manual transmission
with deep
low: Lubricate the clutch fork ball stud through the fitting
on the clutch
housing. Lubricant must be added
.spari11gl~* to the fitting, as very little
is required to lubricate the ball stud surface. Do not add lubricant more
often than specified.
Too much lubricant will damage the clutch
assembly.
Drain, flush and refill the cooling system with new coolant (or every 24
months. whichever occurs first). See "Engine Coolant''
in the Index for
what
to use. Ar? Emissioll Cor1trol Service.
Also inspect the hoses and replace them if they are cracked, swollen or
deteriorated. Tighten all hose clamps (except constant tension clamps).
Remove debris and clean the outside
of the radiator and air
conditioning condenser. Wash
the radiator neck. To ensure proper
operation, pressure test the radiator and cap.
Replace air cleaner filter.
An Emission Control Set-l*icv.
For 2-Wheel Drive vehicles only: Clean and repack the front wheel
bearings (or at each brake relining, whichever occurs first).
Check the crankcase depression regulator valve system for any worn,
plugged or collapsed hoses. See service manual.
AIZ E~ui.ssio~? Co11troI
ScJr-\,ic*e.
Replace fuel filter. Replace filter sooner if it is clogged.-!-
Check the
EGR System (if equipped) (except Code F engine) as
described in the service manual. At7 EIII~SS~OII Control Service.
(C~)11tin~d)
7-93
ProCarManuals.com

Part B: Owner Checks and Services
Listed below are owner checks and services which should be performed at
the intervals specified to help ensure the safety, dependability and emission
control performance of your vehicle.
Be sure any necessary repairs are completed at once. Whenever any fluids
or lubricants are added to your vehicle, make sure they are the proper ones,
as shown in Part D.
At the First 100, 1,000 and 6,000 Miles (160, I 600 and
IO 000 km)
For vehicles with dual wheels, check dual wheel nut torque. For proper
torque, see “Wheel
Nut Torque’’ in the Index.
At Each Fuel Fill
Engine Oil Level
Check the engine oil level and add the proper oil if necessary. See “Engine
Oil”
in the Index for further details.
Engine Coolant Level
Check the engine coolant level and add the proper coolant mix if necessary.
See ”Coolant”
in the Index for further details.
Windshield Washer Fluid Level
Check the windshield washer fluid level in the windshield washer tank and
add the proper fluid if necessary. See ”Windshield Washer Fluid” in the
Index for further details.
At Least Once a Month
Tire Inflation
Check tire inflation. Make sure tires are inflated to the pressures specified
on the Certification/Tire label which is located on the rear edge of the
driver’s door or on the incomplete vehicle document in the cab. See “Tires”
in the Index for further details.
7-93
ProCarManuals.com

Part C: Periodic Maintenance lnspections
Listed below are inspections and services which should be performed at
least twice a year (for instance, each spring and
fall). You should let your
GM dealer’s service department or other qualified service center do these
jobs. Make sure any necessary repairs are completed at once.
Steering and Suspension Inspection
Inspect the front and rear suspension and steering system for damaged.
loose or missing parts, signs of wear,
or lack of lubrication. Inspect power
steering lines and hoses for proper hookup, binding, leaks, cracks, chafing,
etc. (On vehicles equipped with manual steering gear, check for seal
leakage.)
Exhaust System Inspection
Inspect the complete exhaust system. Inspect the body near the exhaust
system.
Look for broken. damaged, missing or out-of-position parts as well
as open seams, holes, loose connections,
or other conditions which could
cause a heat build-up
in the floor pan or could let exhaust fumes into the
vehicle. See “Engine Exhaust”
in the Index.
Accelerator Control System
On gasoline engines. lubricate the pivot at the TBI throttle lever stud with
engine
oil. Do not oil any accelerator or cruise control cables. Replace any
cables that have high effort or excessive wear.
Drive Axle Service
Check readfront axle fluid level and add as needed. Check constant velocity
Joints and axle seals for leaking.
Transfer Case (Four- Wheel Drive) Inspection
Every 12 months or at oil change intervals, check front axle and transfer
case and add lubricant when necessary. Oil the control lever pivot point and
all exposed control linkage. Check vent hose at transfer case for kinks and
proper installation. More frequent lubrication may be required on off-road
use.
7-97
ProCarManuals.com

Part D: necommended Fluids and Lubricants
NOTE: Fluids and lubricants identified below by name, part number or
specification may be obtained from your
GM dealer.
USAGE
Engine Oil (Gasoline Engine)
Engine Oil (Diesel Engine)
Engine Coolant
Coolant Supplement
Hydraulic Brake System
Hydraulic Clutch System
Parking Brake Cables
FLUIDLUBRICANT
Engine oil with the American Pe-
troleum Institute Certified For Gas-
oline Engines “Starburst” symbol of
the proper viscosity.
To determine
the preferred viscosity for your ve-
hicle’s engine, see “Engine Oil”
in
the Index.
Engine oil with the letters
CF-4/SH
is best for your vehicle. However, if
CF-4/SH is not available,
you may
use CF-4/SG or CE/SH or CE/SG
oil. These letters show American
Petroleum Institute (APT) levels
of
quality. They may be listed in re-
verse order, SHKF-4 or other let-
ters such
as, SHKD, CE, CF-4. To
determine the preferred viscosity
for your vehicle’s diesel engine, see
“Engine Oil” in the Index.
50/50 mixture of water and a good
quality ethylene glycol base anti-
freeze
or an approved recycled
coolant conforming
to GM Specifi-
cation 6038-M.
GM Part No. 3634621 or equivalent
with a complete flush and refill.
Delco Supreme
11 @ Brake Fluid
(GM Part
No. 1052535 or equiva-
lent DOT-3 brake fluid).
Hydraulic Clutch Fluid (GM Part
No. 12345347 or equivalent).
Chassis Lubricant
(GM Part No.
1052497 or equivalent) or lubricant
meeting requirements of NLGI
Grade
2, Category LB or GC-LB.
7-98
ProCarManuals.com

USAGE
Power Steering System Manual Transmission (5-Speed
with Low Gear, RPO MT8)
Manual Transmission (5-Speed
without Low Gear, RPO MG5)
Automatic Transmission Key Lock Cylinders
FLUIDLUBRICANT
GM Power Steering Fluid (GM Part
No. 10500 I7 or equivalent).
Castrol Syntorq'
LT or equivalent
(GM Part No. 12346191
- 1 gal.)
(GM Part
No. I23461 90 - 1 qt.).
Synchromesh Transmission Fluid
(GM Part
No. 12345349 or equiva-
lent).
DEXR0N'-I11 Automauc
Transmission Fluid.
Lubricate
with Multi-Purpose Lu-
bricant (GM Part No. I2345 120) or
synthetic SAE SW-30 engine oil.
Automatic Transmission Shift
Linkage
Clutch Fork Ball Stud (5-Speed
with Low Gear)
Floor Shift Linkage
Chassis Lubrication
Front Wheel Bearings
Differential, Standard, Front and
Rear Axle
Differential, Locking
Transfer Case Engine
oil.
Chassis lubricant (GM Part
No.
12346003 or equivalent) or lubri-
cant meeting requirements of NLGI
Grade 2, Category LB or GC-LB.
Engine
oil.
Chassis lubricant (GM Part No.
I2346003 or equivalent) or lubri-
cant meeting requirements of NLGI
Grade
2, Category LB or GC-LB.
Wheel bearing lubricant meeting
requirements
of NLGI Grade 2,
Category GC or GC-LB (GM Part
No. I2346003 or equivalent).
Axle Lubricant (GM Part No.
105227
1 ) or SAE 8OW-90 GL-5
Gear Lubricant.
Axle Lubricant (GM Part
No.
105227 1) or SAE 80W-90 GL-5
Gear Lubricant.
DEXR0N"-111 Automatic
Transmission Fluid.
7-99
ProCarManuals.com

USAGE
Column Shift Lever and Propeller
Shaft
Windshield Washer Solvent
Propeller Shaft Spline/Universal
Joint
Hood Latch Assembly
a. Pivots and Spring Anchor
b. Release Pawl
Hood and Door Hinges
Body Door Hinge Pins, Tailgate
Hinge and Linkage, Folding Seat,
Fuel
Door Hinge
Outer Tailgate Handle Pivot Points
Weatherstrip Conditioning
Weatherstrip Squeaks
Gas Line
FLUIDLUBRICANT
Chassis lubricant meeting require-
ments
of NLGI Grade 2, Category
LB
or GC-LB (GM Part No.
12346003).
GM Optikleen’ Washer Solvent
(GM Part
No. 105 1 5 1 5) or equiva-
lent.
Chassis lubricant (GM Part
No.
12346003 or equivalent) or lubri-
cant meeting requirements
of NLGI
Grade 2, Category LB or GC-LB.
a. Engine oil.
b. Chassis lubricant (GM Part No.
12346003 or equivalent) or lubri-
cant meeting requirements
of NLGI
Grade 2, Category LB or GC-LB.
Engine oil or Lubriplate Lubricant
(GM Part
No. 1050109).
Engine Oil.
Multi-Purpose Lubricant (GM Part
No. 12345 120 or equivalent).
Dielectric Silicone Grease (GM
Part
No. 12345579 or equivalent).
Spray-A-Squeek (GM
Part No.
1 05 2277).
Gas Line De-Icer (GM Part No.
105 15 16).
Part E: Maintenance Record
After the scheduled services are performed, record the date, odometer
reading and who performed the service
in the boxes provided after the
maintenance interval. Any additional information from “Owner Checks and
Services” or “Periodic Maintenance” can be added on the following record
pages. Also, you should retain all maintenance receipts. Your owner
information portfolio
is a convenient place to store them.
7-100
ProCarManuals.com