1995 AUDI A6 relay

24-97
If the LED test light does not light up:

- Repeat test at other terminal of fuse 29.

If the LED test light still does not light up:
- Check wiring for open circuit between fuse 29 and terminal 30 at relay
position 6, using the applicable wiring diagram. Repair wiring as
necessary.

Specified value: max. 1.5

Note:
This step lets the fuel pump run without the engine running. The closed
throttle position switch must be closed during the test, or the selected fuel
injector will discharge fuel when it is actuated 5 times. - Connect VAG1527 LED voltage tester between Ground and one of the
two terminals of fuse 34.
- Initiate output Diagnostic Test Mode (DTM) and advance to test of
cylinder 1 fuel injector -N30- page 01
-51
.

LED test light must light up
Fuel pump relay must be activated
Pa
ge 124 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-98
If the LED test light does not light up:

- Repeat test at other terminal of fuse 34.

If the LED test light still does not light up:
- Check wiring for open circuit between fuse 34 and terminal 31 at relay
position 6, using the applicable wiring diagram. Repair wiring as
necessary.

Specified value: max. 1.5
Pa
ge 126 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-99

Checking fuel pump relay voltage supply and
actuation

- Remove fuel pump relay -J17- from relay panel
position 6.

Checking fuel pump relay voltage supply

- Switch ignition on.

If voltage is NOT OK: - Connect multimeter US1119 (Fluke 83 or similar) and check for voltage
at relay socket:

Terminals 28 (B+) and 34
Terminals 32 (B+) and 34
Specified values: approx. Battery Positive Voltage (B+)
- Repair wiring according to applicable wiring diagram.
Pa
ge 127 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-100

Checking fuel pump relay actuation

Note:
The LED light will light dimly before and after cranking the starter.
If the LED test light does not light up while cranking the starter, check
wiring as follows. - Connect VAG1527B LED voltage tester between relay socket terminals
28 (B+) and 29.
- Briefly crank starter.
LED test light must light up.

If resistance is NOT OK:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder. - Connect VAG1598/22 test box to ECM harness connector page 01
-
67
. (Numbers marked on ECM connector match those on test box).
- Connect multimeter US1119 (Fluke 83 or equivalent) to check for open
circuit between relay socket terminal 29 and test box socket 4.

Specified value: max. 1 - Repair wiring using applicable wiring diagram.
Pa
ge 128 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-101
If the wiring is OK, but the LED test light does not
light up:

- Replace Motronic ECM -J220- page 01
-68
.

- Carry out adaptation of throttle valve control
module to ECM page 24
-150
.

- Check readiness code page 01
-70
. If
Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code page 01
-73
.
If the wiring is OK, and the signal to the fuel
pump relay is OK:

- Replace fuel pump relay -J17-.

- Reinstall fuses.
Pa
ge 129 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

Fuse for fuel injectors OK
Engine speed (RPM) sensor OK
Fuel pump relay OK
Pa
ge 131 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-105

- Check wiring for open circuit between fuel
injector connector terminal 1 and relay panel,
according to wiring diagram.


Specified value: max. 15
- Check wiring for short circuits between wires
and connector terminals.


Specified value:
Fuel injector resistance, checking

If resistance is NOT OK: - Check resistance of individual fuel injectors.

Specified value: 13.5-15.5 - Replace affected fuel injector.
Pa
ge 135 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-121

Checking EVAP canister purge regulator
valve voltage supply

Test conditions

Fuse for EVAP canister purge regulator
valve OK

- Disconnect harness connector from EVAP
canister purge regulator valve.

If LED test light does not light:
If wiring is OK: - Connect VAG1527B LED voltage tester between connector terminal 1
(B+) and engine Ground.
- Operate starter motor.
Specified value: LED must light up
- Check wiring for open circuit between connector terminal 1 and fuse,
according to wiring diagram; repair if necessary.

Specified value: 1.0 max.- Check fuel pump relay page 24
-95
.
Pa
ge 158 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1