1995 AUDI A4 power

24-7


21 -
Engine speed (RPM) sensor -G28-
In transmission housing above differential
22 -
Camshaft Position (CMP) sensor -G40-,
bank 2
23 -
Heated Oxygen Sensor (HO2S) 2 -G108-
with Oxygen Sensor (O2S) heater -Z28- Bank 2, sensor 1
24 -
Knock Sensor (KS) 2 -G66-
25 -
Ignition coils and power output stage
Includes:Ignition coil -N-Ignition coil 2 -N128-Ignition coil 3 -N158-Power output stage -N122-
Pa
ge 7 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-10

WARNING!

Be alert when working on or near the engine
and ignition wires. High secondary ignition
voltage can cause serious personal injury
and damage vehicle components.

DO NOT touch or disconnect ignition system
wires when the engine is running or being
cranked at starting RPM.
DO NOT operate the starter if fuel injectors
are removed.

Be sure the ignition is switched OFF, when:
Disconnecting or connecting the battery,
ignition wires, or test equipment leads
Disconnecting fuel injection system wiring
Washing the engine or engine
compartment.

BEFORE cranking the engine at starting RPM
(e.g. for compression testing) disable ignition
and fuel injection systems:
Disconnect connector for ignition coil power
Pa
ge 10 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-71
Evaluation of display group 2, display field 2 Display group:
2


Display field:
2
Possible malfunction cause
Corrective action
less than 1.00
ms
Smaller values can only occur while driving during
deceleration
more than 2.50
ms Shift lever in drive range (auto. transmission)
Engine is affected by additional consumers- Move shift lever into P or N
- Eliminate load (A/C, power steering, generator)

Poor idle (does not run on all cylinders)- Check and spark plugs page 28
-21
(checking
ignition coils)
- Check fuel injectors page 24
-102


Throttle valve control module -J338- faulty- Check throttle valve control module page 24
-
128

Pa
ge 93 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-72
Evaluation of display group 2, display field 4 Display
group: 2


Display field:
4
Possible malfunction cause
Corrective action
less than 2.8
g/s
Large amount of false air between intake air duct and
Mass Air Flow (MAF) sensor - Check intake air system for leaks (false
air) page 24
-126

larger than 5.6
g/s
Shift lever in drive range (auto. transmission)
Engine affected by additional consumers- Move shift lever into P or N
- Eliminate load (A/C, power steering,
generator)

Open circuits in wire 1 or 2 between MAF sensor and
ECM - Check voltage supply page 24
-73


Open circuit in wire 3 between MAF sensor and relay
panel - Check wiring page 24
-73
Pa
ge 94 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-119

Checking for blockage and leaks
The EVAP canister purge regulator valve is
closed when power is off.

- Remove EVAP canister purge regulator valve -
N80- (component locations page 24
-1 )

- Connect removed valve to harness connector.

- Start output Diagnostic Test Mode (DTM) and
select -N80- page 01
-51
.

- Blow into long connection during output DTM,
and check whether valve opens and closes
properly. Replace valve if necessary.
If valve -N80- does not open and close as
specified:

- Replace -N80-.
If valve -N80- is OK:

- Check all hose connections between tank and
valve for blockage or leaks.
Pa
ge 156 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1