1994 TOYOTA CAMRY ignition

93
* 1 : CALIFORNIA
*
2 : EX. CALIFORNIA
* 3 : EX. CALIFORNIA M/T
*
5 : EX.*
4 *
4 : FOR CANADA IN TMM MADE
CB
17 8 9 13 4 15
146 212 1
23 IP119
IP115
IP313
IP11
IP3196 61
666
M
5 4
E17I18 I18 I18
I18
I18I18 I18 I18 I18
IP3 15IP1 4
BX1 4IJ 1 16
BX1 5
BL IG 2 1
EC B 7B15 B14 B8A11
A
14 B5B6A143
BR±B
GR
G±W
R±W B±O
B±W B±WB±O L±B
G±R
W±B W±B W±BW±B W±B L±B L±BBRR±W G±WGR BR±B
L±BBR R±LW
B±O W
R±L
BRR±LBR BR BR BR
W
G±R
L±B
W±R
B±O
B±O
G±R
BR±B
Y±G
G±W
R±W
(
SHIELDED)G±RL±B
R±LW
BR BR±B
GR
G±W
R±WTT TE1 TE2 VF1 OX1 OX2 E1
B±O B±W
B±W
(
SHIELDED) BR (
SHIELDED) (
SHIELDED) (
SHIELDED)
W±R
D1
E1 OX2 OX1 FCTT TE1 TE2 VF STAW+B FP
E7 ,E8 ,E10
N1
F15
O3FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
10A
STARTER
DATA LINK CONNECTOR 1
(
CHE CK CONNE CTOR)
CIRCUIT
OPENING
RELAY
NOISE FILTER
(
FOR IGNITION SYSTEM)
OXYGEN SENSOR(
MAIN)FUEL
PUMP ENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION ECU)(
A/T)
C
E16 BR1 B
BR BRBR 19
IG±
BR BR
IP316
BR
BR
ED4
I18
BR(
SHIELDED) (
*3)(
*3)
(
*3) (
*3)
B E11 , E12CA,E14
ENGINE CONTROL MODULE(
ENGINE ECU)(
M/T)
3D 2
3C 2
3B20
3A 13
1C 113C 18
1M 1

94
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
E 7(C), E 8(B), E10(A) ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) (A/T)E11(C), E12(B), E14(A) ENGINE CONTROL MODULE (ENGINE ECU) (M/T)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E2:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
VC ± E2:4.5± 5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E2:0.3± 0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
:3.2± 4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
PIM ± E2:3.3± 3.9 VOLTS (IGNITION SW AT ON POSITION)
#10, #20 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (EX. CALIFORNIA)
#10, #20,
#30, #40 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (CALIFORNIA)
THA ± E2:0.5± 3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2± 1.0 VOLTS (IGNITION SW ON AND COOLANT TEMP. 80°C, 176°F)
STA ± E1:6.0±14.0 VOLTS (ENGINE CRANKING)
IGT ± E1: PULSE GENERATION (ENGINE CRANKING OR IDLING)
W ± E1:9.0±14.0 VOLTS (NO TROUBLE AND ENGINE RUNNING)
ACT ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
ACA ± E1:7.5±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW ON)
NSW ± E1:0± 3.0 VOLTS (IGNITION SW ON AND PARK/NEUTRAL POSITION SW (NEUTRAL START SW)
POSITION P OR N POSITION)
9.0±14.0 VOLTS (IGNITION SW ON AND EX. PARK/NEUTRAL POSITION SW
(NEUTRAL START SW) POSITION P OR N POSITION)
RESISTANCE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTORS
(DISCONNECT WIRING CONNECTOR)
IDL ± E2: INFINITY (THROTTLE VALVE OPEN)
2.3 KW OR LESS (THROTTLE VALVE FULLY CLOSED)
VTA ± E2:3.3 ±10.0 KW (THROTTLE VALVE FULLY OPEN)
0.2 ± 0.8 KW (THROTTLE VALVE FULLY CLOSED)
VC ± E2:3.0 ±7 0 KW
THA ± E2:2.0 ±3.0 KW (INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2 ±0.4 KW (COOLANT TEMP. 80°C, 176°F)
G1, NE ± G±:0.17±0.21 KW
ISCC, ISCO± +B, +B1:19.3±22.3 W
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1032E11A32J 133
C 832E12C32K 131
C 9A32E14B32M 131
C10C32F15A34 (S/D), 35 (C/P), 36 (W/G)N 131
D 130I 131O 231
D 230I 231O 331
D 332I 331T 131
D 632I 431V 131
E 130I 531V 231
E 430I 631V 331
E 7C32I 731V 531
E 8B32I1031
E10A32I1233
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
626R/B NO. 6 (BEHIND GLOVE BOX)
SERVICE HINTS

98
ENGINE CONTROL (5S±FE M/T EX. CALIFORNIA)
B4 A
IG2
ACC
IG1 ST2AM2
AM1
ST1
9
1 2
1 2
1 2
1 2 E20
E20
E20I20
I18I23 E20 E17E17
I18
I18
EBC 2C 7
A 25 A12C A 1 A 9A10
B 10 B 11 B12 IP3 12
2 1 2D 2
2B 22C3
31 2 2C A4
W±B
WY
R
B
L RW±R
W±R
W±R
W±RW±R W±R W±R W±R B±O
W±G
B±O B±O
B±O B±OG±Y G±R
LG W±L W±B
BRRB±O B±O B±O W±R
B±O B±O B±O B±O
B±O
# 20 # 10 VC VTA IDLBATT ISCVISCC ISCO +B 15A
EFI
EFI MAIN
RELAY
VSV
(
FOR A/C IDLE±UP) IDLE AIR CONTROL
VALVE
(
ISC VALVE)
ENGINE CONTROL MODULE(
ENGINE ECU)
THROTTLE POSITION
SENSOR
INJECTOR NO. 1
INJECTOR NO. 3
INJECTOR NO. 2
INJECTOR NO. 4 I4
I6
I5
I7
T1 E11 , E12 , E1
V1I1
W±R
IGNITION SW I12
IP1 11
B±O
231 2
B±O G
EGR
VSV
(
FOR EGR)
A FROM POWER SOURCE SYST
25 13
4321
V2IP1 9
W±R
I18
L
L FROM CRUISE
CONTROL ECU
B±O
IP1 18
B±O
B±O
WE18 E18
Y Y W
W
7. 5A
IGN
1D 9
1A 61G 8
EM(
SEEPAGE64)

99
AB
1 2
1 2
1 2 E20
E20
E18 E17 E171234
32 112
C 1A 5 A 18 A 17 A 4
B 2C
4B3B13 B9 B 16 IP116
PIM THW THA THG E2E21 NE NE± G± G+
(
SHIELDED) B B±O W±R W± R
B±O
B±O
R
BRBR BR BR BR
B±Y
BR
BR
BR
BR
BRGR L±BLGW±R W±R
R
L
B
Y
B±O
D6
I3
D2
E11 , E12 , E14 +B1W±R
NE+ NE± G± G+
VC E2PIM
M1
E4
I10
E1
MANIFOLD ABSOLUTE
PRESSURE SENSOR
(
VACUUM SENSOR)
ENGINE COOLANT
TEMP. SENSOR
(
EFI WATER TEMP.
SENSOR)
INTAKE AIR
TEM P. SE NSOR
(
IN±AIR TEMP.
SENSOR)
EGR GAS TEMP.
SENSOR
ENGINE CONTROL MODULE(
ENGINE ECU)
B
DIODE
(
FOR IDLE±UP)
IGNITION COIL
DISTRIBUTOR
I18 E18
BR
BRBR 2 3
C 12
B±R G G
ELS FRO E 64)
1
P
E19
A 3A22
W±R
WB±R
W±R
BB
B
W± R
B± R
12 534
COIL± +B
IG F IGT
IG F IGTIGNITER I2
TO
TACHOMETER
[COMB. METER]
W±R
(
*
2)B±O
B±O
NE+
1D 1415A
TAIL
1A 1010A
MIR±HTR
3C 53D 5
M POWER SOURCE SYSTEM(
SEE PAG

102
ENGINE CONTROL (5S±FE M/T EX. CALIFORNIA)
E11(A), E12(B), E14(C) ENGINE CONTROL MODULE (ENGINE ECU)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
PIM ± E2:3.3± 3.9 VOLTS (IGNITION SW AT ON POSITION)
#10, #20 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
THA ± E2:0.5± 3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2± 1.0 VOLTS (IGNITION SW ON AND COOLANT TEMP. 80°C, 176°F)
STA ± E1:6.0±14.0 VOLTS (ENGINE CRANKING)
IGT ± E1:0.8±1.2 VOLTS (ENGINE CRANKING OR IDLING)
ISCC, ISCO± E1:8.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
W ± E1:9.0±14.0 VOLTS (IGNITION SW ON, NO TROUBLE AND ENGINE RUNNING)
ACT ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
ACA ± E1:7.5±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW ON)
RESISTANCE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTORS
(DISCONNECT WIRING CONNECTOR)
IDL ± E1: INFINITY (THROTTLE VALVE OPEN)
0 W (THROTTLE VALVE FULLY CLOSED)
THA ± E2:2.0 ±3.0 KW (INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2 ±0.4 KW (COOLANT TEMP. 80°C, 176°F)
G+ ± G±:0.17±0.21 KW
ISCC, ISCO± +B, +B1:19.3±22.3 KW
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1032E14C30K 131
C 832F1534 (S/D), 35 (C/P), 36 (W/G)M 131
C 9A32I 131N 131
C10B32I 231O 231
D 130I 331O 331
D 230I 431T 131
D 332I 531V 131
D 632I 631V 231
E 130I 731V 331
E 430I1031V 531
E11A30I1233
E12B30J 133
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
626R/B NO. 6 (BEHIND GLOVE BOX)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1B
1C20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
1M
2A22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3A
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
SERVICE HINTS

109
CURRENT FROM THE BATTERY IS ALWAYS FLOWING FROM THE FL MAIN " HEADLIGHT RELAY (COIL SIDE) " TERMINAL 5 OF THE
DAYTIME RUNNING LIGHT RELAY (MAIN) AND TERMINAL 14 OF THE DIMMER SW, HEADLIGHT RELAY (COIL SIDE) " TERMINAL 3 OF
THE INTEGRATION RELAY " TERMINAL 4 " TERMINAL 13 OF THE LIGHT CONTROL SW, FL MAIN " DAYTIME RUNNING LIGHT
RELAY NO. 2 (COIL SIDE) " TERMINAL 17 OF THE DAYTIME RUNNING LIGHT RELAY.
1. DAYTIME RUNNING LIGHT OPERATION
WHEN THE ENGINE IS STARTED, VOLTAGE GENERATED AT TERMINAL L OF THE GENERATOR (ALTERNATOR) IS APPLIED TO
TERMINAL 11 OF THE DAYTIME RUNNING LIGHT RELAY (MAIN).
IF THE PARKING BRAKE LEVER IS PULLED UP (PARKING BRAKE SW ON) AT THIS TIME, THE RELAY IS NOT ENERGIZED, SO THE
DAYTIME RUNNING LIGHT SYSTEM DOES NOT OPERATE. IF THE PARKING BRAKE LEVER IS RELEASED (PARKING BRAKE LEVER
SW OFF), THE SIGNAL IS INPUT TO TERMINAL 8 OF THE RELAY. THIS ACTIVATES THE RELAY ALSO, CURRENT FROM FL MAIN
FLOWES TO DAYTIME RUNNING LIGHT RELAY NO. 2 (POINT SIDE) " HEAD (UPR±LH) FUSE " TERMINAL 1 OF THE HEAD LH±HI "
TERMINAL 2 " TERMINAL 2 OF THE HEAD RH±HI " TERMINAL 1 " TERMINAL 4 OF THE DAYTIME RUNNING LIGHT RELAY NO. 3 "
TERMINAL 2 " TO GROUND, SO BOTH TAIL AND HEADLIGHT UP.
THIS IS HOW THE DAYTIME RUNNING LIGHT SYSTEM OPERATES. ONCE THE DAYTIME RUNNING LIGHT SYSTEM OPERATES AND
HEAD HAVE LIGHT UP, HEAD REMAIN ON EVEN IF THE PARKING BRAKE LEVER IS PULLED UP (PARKING BRAKE SW ON).
EVEN IF THE ENGINE STALLS WITH THE IGNITION SW ON AND THERE IS NO VOLTAGE FROM TERMINAL L OF THE GENERATOR
(ALTERNATOR), HEAD REMAIN ON. IF THE IGNITION SW IS THEN TURNED OFF, AND HEAD ARE TURNED OFF.
IF THE ENGINE IS STARTED WHILE THE PARKING BRAKE LEVER IS RELEASED (PARKING BRAKE SW OFF), THE DAYTIME RUNNING
LIGHT SYSTEM OPERATES AND TAIL, HEADLIGHT UP AS THE ENGINE STARTS.
2. HEADLIGHT OPERATION
*(WHEN THE LIGHT CONTROL SW AT THE HEAD POSITION)
WHEN THE LIGHT CONTROL SW IS SET TO HEAD POSITION, THE CURRENT FLOWING TO THE HEADLIGHT RELAY (COIL SIDE)
FLOWS TO TERMINAL 3 OF THE INTEGRATION RELAY " TERMINAL 4 " TERMINAL 13 OF THE LIGHT CONTROL SW " TERMINAL 11
" GROUND, TURNING THE HEADLIGHT RELAY ON.
THIS CAUSES THE CURRENT FLOWING TO THE HEADLIGHT RELAY (POINT SIDE) " DRL FUSE " DAYTIME RUNNING LIGHT RELAY
NO. 3 (COIL SIDE) AND DAYTIME RUNNING LIGHT RELAY NO. 4 (COIL SIDE) " GROUND, TURNING THE DAYTIME RUNNING LIGHT
RELAY NO. 3 AND NO. 4 ON. ALSO, CURRENT FROM THE HEADLIGHT RELAY (POINT SIDE) TO HEAD (LWR) FUSES " TERMINAL 1
OF THE HEADLIGHTS (LO) " TERMINAL 2 " GROUND, SO THE HEADLIGHTS (LO) LIGHT UP.
*(DIMMER SW AT FLASH POSITION)
WHEN THE DIMMER SW IS SET TO FLASH POSITION, CURRENT FLOWS FROM HEADLIGHT RELAY (COIL SIDE) " TERMINAL 14 OF
THE DIMMER SW " TERMINAL 9 " GROUND, TURNING THE HEADLIGHT RELAY ON. AT THE SAME TIME, SIGNALS ARE OUTPUT
FROM TERMINAL 12 AND TERMINAL 14 OF THE DIMMER SW TO TERMINAL 16 AND TERMINAL 5 OF THE DAYTIME RUNNING LIGHT
RELAY (MAIN), ACTIVATING THE DAYTIME RUNNING LIGHT RELAY (MAIN) AND ALSO THE DAYTIME RUNNING LIGHT RELAY NO. 2.
WHEN THE HEADLIGHT RELAY AND DAYTIME RUNNING LIGHT RELAY (MAIN) ARE ACTIVATED, THE HEADLIGHTS (LO AND HI) THEN
LIGHT UP.
*(DIMMER SW AT HIGH POSITION)
WHEN THE LIGHT CONTROL SW IS SET TO HEAD POSITION, A SIGNAL IS OUTPUT FROM TERMINAL 13 OF THE LIGHT CONTROL SW
" TERMINAL 4 OF THE INTEGRATION RELAY " TERMINAL 3 " TERMINAL 5 OF THE DAYTIME RUNNING LIGHT RELAY (MAIN).
WHEN THE DIMMER SW IS SET TO HIGH POSITION, A SIGNAL IS OUTPUT FROM TERMINAL 12 OF THE DIMMER SW TO TERMINAL 16
OF THE DAYTIME RUNNING LIGHT RELAY (MAIN). THESE SIGNALS ACTIVATE DAYTIME RUNNING LIGHT RELAY NO. 2, SO CURRENT
FLOWS FROM DAYTIME RUNNING LIGHT RELAY NO. 2 (POINT SIDE) " HEAD (UPR±LH) FUSE " TERMINAL 1 OF THE HEADLIGHT
LH±HI " TERMINAL 2 " DAYTIME RUNNING LIGHT RELAY NO. 4 (POINT SIDE) " GROUND, AND CURRENT ALSO SIMUTANEOUSLY
FLOWS FROM HEAD (UPR±RH) FUSE " DAYTIME RUNNING LIGHT RELAY NO. 3 (POINT SIDE) " TERMINAL 1 OF THE HEADLIGHT
RH±HI " TERMINAL 2 " DAYTIME RUNNING LIGHT RELAY NO. 4 (POINT SIDE), CAUSING THE HEADLIGHTS (HI SIDE) TO LIGHT UP.
D 4 DAYTIME RUNNING LIGHT RELAY (MAIN)
2±GROUND : APPROX. 12 VOLTS WITH THE IGNITION SW AT ON POSITION
15±GROUND : ALWAYS APPROX. 12 VOLTS
8±GROUND : CONTINUITY WITH THE PARKING BRAKE LEVER PULLED UP (PARKING BRAKE SW ON)
13±GROUND : ALWAYS CONTINUITY
SYSTEM OUTLINE
SERVICE HINTS

11 3
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 7 OF THE INTEGRATION RELAY THROUGH GAUGE FUSE.
VOLTAGE IS APPLIED AT ALL TIMES TO TERMINAL (A) 2 OF THE INTEGRATION RELAY THROUGH THE TAILLIGHT RELAY (COIL SIDE),
AND TO TERMINAL (A) 3 THROUGH THE HEADLIGHT RELAY (COIL SIDE).
1. NORMAL LIGHTING OPERATION
(TURN TAILLIGHT ON)
WITH LIGHT CONTROL SW TURNED TO TAILLIGHT POSITION, A SIGNAL IS INPUT INTO TERMINAL (A) 1 OF THE INTEGRATION
RELAY. ACCORDING TO THIS SIGNAL, THE CURRENT FLOWING TO TERMINAL (A) 2 OF THE RELAY FLOWS FROM TERMINAL (A) 1 "
TERMINAL 2 OF THE LIGHT CONTROL SW " TERMINAL 11 " TO GROUND AND TAILLIGHT RELAY CAUSES TAILLIGHT TO TURN ON.
(TURN HEADLIGHT ON)
WITH LIGHT CONTROL SW TURNED TO HEADLIGHT POSITION, A SIGNAL IS INPUT INTO TERMINALS (A) 1 AND (A) 4 OF THE
INTEGRATION RELAY. ACCORDING TO THIS SIGNAL, THE CURRENT FLOWING TO TERMINAL (A) 3 OF THE RELAY FLOWS TO
TERMINAL (A) 4 " TERMINAL 13 OF THE LIGHT CONTROL SW " TERMINAL 11 " TO GROUND IN THE HEADLIGHT CIRCUIT, AND
CAUSES TAILLIGHT AND HEADLIGHT RELAY TO TURN THE LIGHT ON. THE TAILLIGHT CIRCUIT IS SAME AS ABOVE.
2. LIGHT AUTO TURN OFF OPERATION
WITH LIGHTS ON AND IGNITION SW TURNED OFF (INPUT SIGNAL GOES TO TERMINAL 7 OF THE RELAY), WHEN DOOR ON DRIVER'S
SIDE IS OPENED (INPUT SIGNAL GOES TO TERMINAL 6 OF THE RELAY), THE RELAY OPERATES AND THE CURRENT IS CUT OFF
WHICH FLOWS FROM TERMINAL (A) 2 OF THE RELAY TO TERMINAL (A) 1 IN TAILLIGHT CIRCUIT AND FROM TERMINAL (A) 3 TO
TERMINAL (A) 4 IN HEADLIGHT CIRCUIT. AS A RESULT, ALL LIGHTS ARE TURNED OFF AUTOMATICALLY.
I13 INTEGRATION RELAY
7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
1±GROUND : ALWAYS APPROX. 12 VOLTS
(A)3±GROUND : APPROX. 12 VOLTS WITH LIGHT CONTROL SW AT OFF OR TAIL POSITION
(A)2±GROUND : APPROX. 12 VOLTS WITH LIGHT CONTROL SW AT OFF POSITION
6±GROUND : CONTINUITY WITH FRONT LH DOOR OPEN
(A)4±GROUND : CONTINUITY WITH LIGHT CONTROL SW AT HEAD POSITION
(A)1±GROUND : CONTINUITY WITH LIGHT CONTROL SW AT TAIL OR HEAD POSITION
10±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1232F10A28 (1MZ±FE), 30 (5S±FE)F16C28 (1MZ±FE), 30 (5S±FE)
D1234 (S/D), 35 (C/P), 36 (W/G)F10B28 (1MZ±FE), 30 (5S±FE)I13A33
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B
1C20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1E
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)ENGINE WIRE AND COWL WIREEF140 (5S±FE)ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IE42LEFT KICK PANEL
IG42INSTRUMENT PANEL BRACE LH
SYSTEM OUTLINE
SERVICE HINTS

11 5
TURN SIGNAL FLASHER
(1) 2±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON OR HAZARD SW ON
(1) 1±GROUND : CHANGES FROM APPROX. 12 TO 0 VOLTS WITH IGNITION SW ON AND TURN SIGNAL SW LEFT OR RIGHT, OR
HAZARD SW ON
(1) 3±GROUND: ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 832F 828 (1MZ±FE), 30 (5S±FE)R 834 (S/D), 35 (C/P)
C1232H 733R1034 (S/D), 35 (C/P)
F 728 (1MZ±FE), 30 (5S±FE)J 133
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1C20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
2F22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3C24COWL WIRE AND J/B NO 3 (BEHIND COMBINATION METER)3D24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
ED138 (1MZ±FE)COWL WIRE AND ENGINE ROOM MAIN WIREED140 (5S±FE)COWL WIRE AND ENGINE ROOM MAIN WIRE
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
BZ146 (S/D)LUGGAGE ROOM NO 1 WIRE AND FLOOR NO 1 WIREBZ148 (C/P)LUGGAGE ROOM NO. 1 WIRE AND FLOOR NO. 1 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA38 (1MZ±FE)FRONT RIGHT FENDEREA40 (5S±FE)FRONT RIGHT FENDER
EB38 (1MZ±FE)FRONT LEFT FENDEREB40 (5S±FE)FRONT LEFT FENDER
IE42LEFT KICK PANEL
IG42INSTRUMENT PANEL BRACE LH
BO46 (S/D)LEFT QUARTER PILLARBO48 (C/P)LEFT QUARTER PILLAR
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 744COWL WIREI1144COWL WIRE
SERVICE HINTS