1994 TOYOTA CAMRY start

88
ENGINE CONTROL (5S±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE ECU (M/T), ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU (A/T)) AND MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE
ENGINE CONTROL IS EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL SYSTEM
THE ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE ENGINE COOLANT TEMP. (WATER TEMP.)
THUS THE ENGINE COOLANT TEMP. (WATER TEMP.) IS INPUT IN THE FORM OF A CONTROL SIGNAL TO TERMINAL THW OF
THE ENGINE CONTROL MODULE (ECU).
(2) INTAKE AIR TEMP. SIGNAL SYSTEM
THE INTAKE AIR TEMP. SENSOR (IN±AIR TEMP. SENSOR) IS DETECTS THE INTAKE AIR TEMP., WHICH IS INPUT AS A
CONTROL SIGNAL TO TERMINAL THA OF THE ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OX1 AND
OX2 OF THE ENGINE CONTROL MODULE (ECU).
(4) RPM SIGNAL SYSTEM
CRANKSHAFT POSITION AND ENGINE RPM ARE DETECTED BY THE PICK±UP COIL INSTALLED INSIDE THE DISTRIBUTOR.
CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINALS G+ AND G2 (CALIFORNIA), OF THE ENGINE
CONTROL MODULE (ECU), AND RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL SYSTEM
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE, WHICH IS INPUT AS A CONTROL
SIGNAL TO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU), OR WHEN THE VALVE IS FULLY CLOSED, TO
TERMINAL IDL
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SPD OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM (A/T)
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION ARE IN NEUTRAL AND
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TARMINAL ACA OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, THE VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS
+B AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY. THE CURRENT FLOWING THROUGH THE IGN FUSE
FLOWS TO TERMINAL IGSW OF THE ENGINE CONTROL MODULE (ECU).
(10) INTAKE AIR VOLUME SIGNAL SYSTEM
INTAKE AIR VOLUME IS DETECTED BY THE MANIFOLD ABSOLUTE PRESSURE SENSOR (VACUUM SENSOR) (FOR MANIFOLD
PRESSURE) AND IS INPUT AS A CONTROL SIGNAL TO TERMINAL PIM OF THE ENGINE CONTROL MODULE (ECU).
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR AND THE SIGNAL IS INPUT INTO TERMINAL KNK AS A CONTROL
SIGNAL.
(13) ELECTRICAL LOAD SIGNAL SYSTEM
THE SIGNAL WHEN SYSTEMS SUCH AS THE REAR WINDOW DEFOGGER, HEADLIGHTS, ETC. WHICH CAUSE A HIGH
ELECTRICAL BURDEN ARE ON IS INPUT TO TERMINAL ELS AS A CONTROL SIGNAL.
SYSTEM OUTLINE

92
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
CB
A
321
C
1 78
C
A 6
B 3
A 21 A10 C13 C26 B13A 5
EDI13G±R R±L R±L
G±R
G±R
Y±G G±WBR LG±B
B±Y
W W±B W±B
W±R
B±O
B±O
B
G±R B±O B±O W±R
R±W G±WY±G G±R
E1 TE2 TE1
WW
DATA LINK CONNECTOR 2
(
TDCL) FROM CE SYSTEM
(
SEE P
JUNCTION
CONNECTOR
MALFUNCTION INDICATOR
LAMP(
CHECK E NG INE
WARNING LIGHT)
[COMB. METER]
ACT ACA E01 E02 KNKENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)(
A/T)
ACT ACA
KNOCK
SENSOR A/C AMPLIFIER A1 0K1 E7 ,E8 ,E10
A
C9 , C10
J1D3
B
(
SHIELDED)
(
SHIELDED)
E16
O2
OXYGEN SENSOR
(
SUB)
1E15BR
BR
5TT
BR±B IP3 11 IP314
A 9 23
4 1
512IP3 2
SPEED
LGP G±B
G V±Y V±Y
R±L
R±L
SP1COMBINATION
METER C8
VEHICLE
SPEED SENSOR
(
SPEED SENSOR) V5
B
BR I13
G±R
G±R(
*5)
(
*4)
R±L
BR BR
1 2BR 7
R±W
ENG
BR
R±L
I18
R±L TO PARK/NEUTRAL POSITION
SW(
NEUTRAL START SW)
TO GENERATOR(
ALTERNATOR)
R±L
G±R(
*5)(
*4)
(
*3)
B E11 , E12CA,E14
ENGINE CONTROL MODULE(
ENGINE ECU)(
M/T) G±R
(
*
4)
1B 6 10A
GAUGE
1D6
3D 73D19
3D 18
3D 22
3D 10
3D 3
3D 12
POWER SOUR
AGE 64)

93
* 1 : CALIFORNIA
*
2 : EX. CALIFORNIA
* 3 : EX. CALIFORNIA M/T
*
5 : EX.*
4 *
4 : FOR CANADA IN TMM MADE
CB
17 8 9 13 4 15
146 212 1
23 IP119
IP115
IP313
IP11
IP3196 61
666
M
5 4
E17I18 I18 I18
I18
I18I18 I18 I18 I18
IP3 15IP1 4
BX1 4IJ 1 16
BX1 5
BL IG 2 1
EC B 7B15 B14 B8A11
A
14 B5B6A143
BR±B
GR
G±W
R±W B±O
B±W B±WB±O L±B
G±R
W±B W±B W±BW±B W±B L±B L±BBRR±W G±WGR BR±B
L±BBR R±LW
B±O W
R±L
BRR±LBR BR BR BR
W
G±R
L±B
W±R
B±O
B±O
G±R
BR±B
Y±G
G±W
R±W
(
SHIELDED)G±RL±B
R±LW
BR BR±B
GR
G±W
R±WTT TE1 TE2 VF1 OX1 OX2 E1
B±O B±W
B±W
(
SHIELDED) BR (
SHIELDED) (
SHIELDED) (
SHIELDED)
W±R
D1
E1 OX2 OX1 FCTT TE1 TE2 VF STAW+B FP
E7 ,E8 ,E10
N1
F15
O3FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
10A
STARTER
DATA LINK CONNECTOR 1
(
CHE CK CONNE CTOR)
CIRCUIT
OPENING
RELAY
NOISE FILTER
(
FOR IGNITION SYSTEM)
OXYGEN SENSOR(
MAIN)FUEL
PUMP ENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION ECU)(
A/T)
C
E16 BR1 B
BR BRBR 19
IG±
BR BR
IP316
BR
BR
ED4
I18
BR(
SHIELDED) (
*3)(
*3)
(
*3) (
*3)
B E11 , E12CA,E14
ENGINE CONTROL MODULE(
ENGINE ECU)(
M/T)
3D 2
3C 2
3B20
3A 13
1C 113C 18
1M 1

94
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
E 7(C), E 8(B), E10(A) ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) (A/T)E11(C), E12(B), E14(A) ENGINE CONTROL MODULE (ENGINE ECU) (M/T)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E2:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
VC ± E2:4.5± 5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E2:0.3± 0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
:3.2± 4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
PIM ± E2:3.3± 3.9 VOLTS (IGNITION SW AT ON POSITION)
#10, #20 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (EX. CALIFORNIA)
#10, #20,
#30, #40 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (CALIFORNIA)
THA ± E2:0.5± 3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2± 1.0 VOLTS (IGNITION SW ON AND COOLANT TEMP. 80°C, 176°F)
STA ± E1:6.0±14.0 VOLTS (ENGINE CRANKING)
IGT ± E1: PULSE GENERATION (ENGINE CRANKING OR IDLING)
W ± E1:9.0±14.0 VOLTS (NO TROUBLE AND ENGINE RUNNING)
ACT ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
ACA ± E1:7.5±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW ON)
NSW ± E1:0± 3.0 VOLTS (IGNITION SW ON AND PARK/NEUTRAL POSITION SW (NEUTRAL START SW)
POSITION P OR N POSITION)
9.0±14.0 VOLTS (IGNITION SW ON AND EX. PARK/NEUTRAL POSITION SW
(NEUTRAL START SW) POSITION P OR N POSITION)
RESISTANCE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTORS
(DISCONNECT WIRING CONNECTOR)
IDL ± E2: INFINITY (THROTTLE VALVE OPEN)
2.3 KW OR LESS (THROTTLE VALVE FULLY CLOSED)
VTA ± E2:3.3 ±10.0 KW (THROTTLE VALVE FULLY OPEN)
0.2 ± 0.8 KW (THROTTLE VALVE FULLY CLOSED)
VC ± E2:3.0 ±7 0 KW
THA ± E2:2.0 ±3.0 KW (INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2 ±0.4 KW (COOLANT TEMP. 80°C, 176°F)
G1, NE ± G±:0.17±0.21 KW
ISCC, ISCO± +B, +B1:19.3±22.3 W
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1032E11A32J 133
C 832E12C32K 131
C 9A32E14B32M 131
C10C32F15A34 (S/D), 35 (C/P), 36 (W/G)N 131
D 130I 131O 231
D 230I 231O 331
D 332I 331T 131
D 632I 431V 131
E 130I 531V 231
E 430I 631V 331
E 7C32I 731V 531
E 8B32I1031
E10A32I1233
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
626R/B NO. 6 (BEHIND GLOVE BOX)
SERVICE HINTS

101
* 2 : TMM MADE *
1:TMCMADE
AB
8913 415
146 212 1
23 IP313
IP11
IP3196 62C A6
666
M
5 4 I18
I18I18 I18 I18
IP3 15IP1 4
BX1 4IJ1 16IP3 18
BX1 5
BL IG 2 1
ECB 15 B7B8A2
C
B 1B6C43
GR
G±W
R±W B±O
B±W B±W B±WB±O L±B
G±R
W±B W±B W±BW±B W±B L±B L±BBRR±W G±WGR
L±BBR R±LW
B±O W BRR±L
W
G±R
L±B
W±R
B±O
B±O
G±R
Y±G
G±W
R±W
(
SHIELDED)G±RL±B
R±LW
BR
BR GR
G±W
R±WTE1 TE2 VF1 OX1 OX2 E1
B±O B±W
W±RD1
OX2 OX1 FCTE1 TE2 VF STAWB FP
E11 , E12 , E14
N1
F15
O3
O2FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
10A
STARTER
DATA LINK CONNECTOR 1
(
CHECK CONNECTOR)
CIRCUIT
OPENING
RELAY
NOISE FILTER
(
FOR I GNITI ON
SYSTEM)
OXYGEN SENSOR
(
SUB)OXYGEN SENSOR
(
MAIN)FUEL
PUMP ENGINE CONTROL MODULE(
ENGINE ECU) IG± 19 B
BR(
SHIELDED) IP119
ED 2 11 IP316
BR BR(
SHIELDED)
(
SHIELDED)
R±L
BR BR
BR
BR
B±W
(
*2)(
*1)
B±W
E17
3C 2
3D 23B
3A 13
3C 18
1C 11
1M 1

109
CURRENT FROM THE BATTERY IS ALWAYS FLOWING FROM THE FL MAIN " HEADLIGHT RELAY (COIL SIDE) " TERMINAL 5 OF THE
DAYTIME RUNNING LIGHT RELAY (MAIN) AND TERMINAL 14 OF THE DIMMER SW, HEADLIGHT RELAY (COIL SIDE) " TERMINAL 3 OF
THE INTEGRATION RELAY " TERMINAL 4 " TERMINAL 13 OF THE LIGHT CONTROL SW, FL MAIN " DAYTIME RUNNING LIGHT
RELAY NO. 2 (COIL SIDE) " TERMINAL 17 OF THE DAYTIME RUNNING LIGHT RELAY.
1. DAYTIME RUNNING LIGHT OPERATION
WHEN THE ENGINE IS STARTED, VOLTAGE GENERATED AT TERMINAL L OF THE GENERATOR (ALTERNATOR) IS APPLIED TO
TERMINAL 11 OF THE DAYTIME RUNNING LIGHT RELAY (MAIN).
IF THE PARKING BRAKE LEVER IS PULLED UP (PARKING BRAKE SW ON) AT THIS TIME, THE RELAY IS NOT ENERGIZED, SO THE
DAYTIME RUNNING LIGHT SYSTEM DOES NOT OPERATE. IF THE PARKING BRAKE LEVER IS RELEASED (PARKING BRAKE LEVER
SW OFF), THE SIGNAL IS INPUT TO TERMINAL 8 OF THE RELAY. THIS ACTIVATES THE RELAY ALSO, CURRENT FROM FL MAIN
FLOWES TO DAYTIME RUNNING LIGHT RELAY NO. 2 (POINT SIDE) " HEAD (UPR±LH) FUSE " TERMINAL 1 OF THE HEAD LH±HI "
TERMINAL 2 " TERMINAL 2 OF THE HEAD RH±HI " TERMINAL 1 " TERMINAL 4 OF THE DAYTIME RUNNING LIGHT RELAY NO. 3 "
TERMINAL 2 " TO GROUND, SO BOTH TAIL AND HEADLIGHT UP.
THIS IS HOW THE DAYTIME RUNNING LIGHT SYSTEM OPERATES. ONCE THE DAYTIME RUNNING LIGHT SYSTEM OPERATES AND
HEAD HAVE LIGHT UP, HEAD REMAIN ON EVEN IF THE PARKING BRAKE LEVER IS PULLED UP (PARKING BRAKE SW ON).
EVEN IF THE ENGINE STALLS WITH THE IGNITION SW ON AND THERE IS NO VOLTAGE FROM TERMINAL L OF THE GENERATOR
(ALTERNATOR), HEAD REMAIN ON. IF THE IGNITION SW IS THEN TURNED OFF, AND HEAD ARE TURNED OFF.
IF THE ENGINE IS STARTED WHILE THE PARKING BRAKE LEVER IS RELEASED (PARKING BRAKE SW OFF), THE DAYTIME RUNNING
LIGHT SYSTEM OPERATES AND TAIL, HEADLIGHT UP AS THE ENGINE STARTS.
2. HEADLIGHT OPERATION
*(WHEN THE LIGHT CONTROL SW AT THE HEAD POSITION)
WHEN THE LIGHT CONTROL SW IS SET TO HEAD POSITION, THE CURRENT FLOWING TO THE HEADLIGHT RELAY (COIL SIDE)
FLOWS TO TERMINAL 3 OF THE INTEGRATION RELAY " TERMINAL 4 " TERMINAL 13 OF THE LIGHT CONTROL SW " TERMINAL 11
" GROUND, TURNING THE HEADLIGHT RELAY ON.
THIS CAUSES THE CURRENT FLOWING TO THE HEADLIGHT RELAY (POINT SIDE) " DRL FUSE " DAYTIME RUNNING LIGHT RELAY
NO. 3 (COIL SIDE) AND DAYTIME RUNNING LIGHT RELAY NO. 4 (COIL SIDE) " GROUND, TURNING THE DAYTIME RUNNING LIGHT
RELAY NO. 3 AND NO. 4 ON. ALSO, CURRENT FROM THE HEADLIGHT RELAY (POINT SIDE) TO HEAD (LWR) FUSES " TERMINAL 1
OF THE HEADLIGHTS (LO) " TERMINAL 2 " GROUND, SO THE HEADLIGHTS (LO) LIGHT UP.
*(DIMMER SW AT FLASH POSITION)
WHEN THE DIMMER SW IS SET TO FLASH POSITION, CURRENT FLOWS FROM HEADLIGHT RELAY (COIL SIDE) " TERMINAL 14 OF
THE DIMMER SW " TERMINAL 9 " GROUND, TURNING THE HEADLIGHT RELAY ON. AT THE SAME TIME, SIGNALS ARE OUTPUT
FROM TERMINAL 12 AND TERMINAL 14 OF THE DIMMER SW TO TERMINAL 16 AND TERMINAL 5 OF THE DAYTIME RUNNING LIGHT
RELAY (MAIN), ACTIVATING THE DAYTIME RUNNING LIGHT RELAY (MAIN) AND ALSO THE DAYTIME RUNNING LIGHT RELAY NO. 2.
WHEN THE HEADLIGHT RELAY AND DAYTIME RUNNING LIGHT RELAY (MAIN) ARE ACTIVATED, THE HEADLIGHTS (LO AND HI) THEN
LIGHT UP.
*(DIMMER SW AT HIGH POSITION)
WHEN THE LIGHT CONTROL SW IS SET TO HEAD POSITION, A SIGNAL IS OUTPUT FROM TERMINAL 13 OF THE LIGHT CONTROL SW
" TERMINAL 4 OF THE INTEGRATION RELAY " TERMINAL 3 " TERMINAL 5 OF THE DAYTIME RUNNING LIGHT RELAY (MAIN).
WHEN THE DIMMER SW IS SET TO HIGH POSITION, A SIGNAL IS OUTPUT FROM TERMINAL 12 OF THE DIMMER SW TO TERMINAL 16
OF THE DAYTIME RUNNING LIGHT RELAY (MAIN). THESE SIGNALS ACTIVATE DAYTIME RUNNING LIGHT RELAY NO. 2, SO CURRENT
FLOWS FROM DAYTIME RUNNING LIGHT RELAY NO. 2 (POINT SIDE) " HEAD (UPR±LH) FUSE " TERMINAL 1 OF THE HEADLIGHT
LH±HI " TERMINAL 2 " DAYTIME RUNNING LIGHT RELAY NO. 4 (POINT SIDE) " GROUND, AND CURRENT ALSO SIMUTANEOUSLY
FLOWS FROM HEAD (UPR±RH) FUSE " DAYTIME RUNNING LIGHT RELAY NO. 3 (POINT SIDE) " TERMINAL 1 OF THE HEADLIGHT
RH±HI " TERMINAL 2 " DAYTIME RUNNING LIGHT RELAY NO. 4 (POINT SIDE), CAUSING THE HEADLIGHTS (HI SIDE) TO LIGHT UP.
D 4 DAYTIME RUNNING LIGHT RELAY (MAIN)
2±GROUND : APPROX. 12 VOLTS WITH THE IGNITION SW AT ON POSITION
15±GROUND : ALWAYS APPROX. 12 VOLTS
8±GROUND : CONTINUITY WITH THE PARKING BRAKE LEVER PULLED UP (PARKING BRAKE SW ON)
13±GROUND : ALWAYS CONTINUITY
SYSTEM OUTLINE
SERVICE HINTS

152
BACK±UP LIGHT
IP3 2
8 2
1 2
IP3 1
Bd2 3IJ1 10
B38
BR FROM POWER SOURCE SYSTEM(
SEEPAGE64)
R±L
R±B
R±B
R±L R±L R±B R±B R±B R±B R±B W±B
BACK±UP
LIGHT SW BACK±UP LIGHT SW
[PARK/NEUTRAL
POSITION SW
(
NEUTRAL START SW)
]B1 P1(
M/T)
(
A/T)
(
M/T)(
A/T)
Bc2 6
R±B
W±BBa1 3
B16
B16 Ba 14
BL W±BR±B
W±B R±B
W±B W±B
R±B R±B(
W/G)
(
S/D, C/P)
(
S /D, C/P) (
S/D, W/G) (
W/G)(
W/G)
(
S/D, C/P)
(
W/G)(
S /D, C/P)
(
W/G)R±L
(
A/T)
R±L TO VEHICLE SPEED SENSOR
(
SPEED SENSOR)
TO GENERATOR(
ALTERNATOR)TO VEHICLE SPEED SENSOR
(
SPEED SENSOR)
TO GE NERATOR(
ALTERNATOR) R±L
R±L
(
M/T)
(
A/T)
(
M/T)
I18
I18
B 3A 4
B 3A 4 (
S/D, C/P)
(
W/G)(
S/D, C/P)
(
W/G)
A 3A3
B 4 B 4(
S/D, C/P)
(
W/G) (
S/D, C/P)
(
W/G)B R9 ,A
BA CK ±UP LIGHT LH
[REAR COMB. LIGHT LH]B R11 ,A
BACK±UP LIGHT RH
[REAR COMB. LIGHT RH]
1D 610A
GAUGE

153
B 1 BACK±UP LIGHT SW
2±1 : CLOSED WITH SHIFT LEVER IN R POSITION
P 1 BACK±UP LIGHT SW [PARK/NEUTRAL POSITION SW (NEUTRAL START SW)]
6±5 : CLOSED WITH SHIFT LEVER IN R POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 130R 934 (S/D), 35 (C/P), 36 (W/G)
P 129 (1MZ±FE), 31 (5S±FE)R1134 (S/D), 35 (C/P), 36 (W/G)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
IP344ENGINE WIRE AND COWL WIRE
Ba146 (S/D)FLOOR NO 1 WIRE AND LUGGAGE ROOM NO 2 WIREBa148 (C/P)FLOOR NO. 1 WIRE AND LUGGAGE ROOM NO. 2 WIRE
Bc250 (W/G)BACK DOOR NO. 1 WIRE AND FLOOR NO. 1 WIRE
Bd250 (W/G)BACK DOOR NO. 1 WIRE AND BACK DOOR NO. 2 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
46 (S/D)
BL48 (C/P)UNDER THE LEFT QUARTER PILLARBL
50 (W/G)
UNDER THE LEFT QUARTER PILLAR
BR50 (W/G)BACK DOOR CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I1844ENGINE WIREB3850 (W/G)BACK DOOR NO. 2 WIRE
B1646 (S/D)LUGGAGE ROOM NO. 2 WIRE
34 B1 P 1 ,GRAY GRAY
12X2
8B R9 ,ABR11 ,A
SERVICE HINTS