1994 TOYOTA CAMRY wiring

44
ELECTRICAL WIRING ROUTING
: Location of Connector Joining Wire Harness and Wire Harness
: Location of Splice Points

[Sedan]
[Sedan]
46
ELECTRICAL WIRING ROUTING
: Location of Connector Joining Wire Harness and Wire Harness
: Location of Ground Points
: Location of Splice Points

[Coupe]
[Coupe]
48
ELECTRICAL WIRING ROUTING
: Location of Connector Joining Wire Harness and Wire Harness
: Location of Ground Points
: Location of Splice Points

[Wagon]
[Wagon]
50
ELECTRICAL WIRING ROUTING
: Location of Connector Joining Wire Harness and Wire Harness
: Location of Ground Points
: Location of Splice Points

84
ENGINE CONTROL (1MZ±FE)
CIRCUIT OPENING RELAY2±1 : CLOSED WITH STARTER RUNNING OR MEASURING PLATE (VOLUME AIR FLOW (AIR FLOW METER)) OPEN
EFI MAIN RELAY2±4 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
E 4
ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) 1±2 : 10.0 ± 20.0 K (±20°C, ±4°F)
: 4.0 ± 7.0 K (0°C, 32°F)
: 2.0 ± 3.0 K (20°C, 68°F)
: 0.9 ± 1.3 K (40°C, 104°F)
: 0.4 ± 0.7 K (60°C, 140°F)
: 0.2 ± 0.4 K (80°C, 176°F)
E 7(A), E 8(B), E 9(C), E10(D)
ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY OPEN)
0±3.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
VC ± E1: ALWAYS 4.5±5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E1:0.3±0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
3.2±4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY OPEN)
VG ± E1:4.0±5.5 VOLTS (IGNITION SW AT ON POSITION)
THA ± E1:0.5±3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E1:0.2±1.0 VOLTS (ENGINE IDLING AND COOLANT TEMP. 80°C, 176°F)
#10, #20, #30, #40, #50, #60
± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
PULSE GENERATION (ENGINE IDLING)
IGT1, IGT2, IGT3
IGT4, IGT5, IGT6 ± E1: PULSE GENERATION (ENGINE IDLING)
IGF ± E1:4.5±5.5 VOLTS (IGNITION SW AT ON POSITION)
PULSE GENERATION (ENGINE IDLING)
G22+ ± G±: PULSE GENERATION (ENGINE IDLING)
NE+ ± G±: PULSE GENERATION (ENGINE IDLING)
RSC, RSO ± E1: PULSE GENERATION (ENGINE IDLING AND A/C OPERATION)
OXS, OXL, OXR ± E1: PULSE GENERATION (MAINTAIN ENGINE SPEED AT 2500 RPM FOR TWO MINUTES AFTER WARMING UP)
HTS, HTL, HTR ± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
0±3.0 VOLTS (ENGINE IDLING)
KNKL, KNLR ± E1: PULSE GENERATION (ENGINE IDLING)
NSW ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND OTHER SHIFT POSITION IN P OR N POSITION)
BELOW 3.0 VOLTS (IGNITION SW ON AND SHIFT POSITION IN P OR N POSITION)
SP1 ± E1: PULSE GENERATION (IGNITION SW ON AND ROTATE DRIVING WHEEL SLOWLY)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
TE2 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
W ± E1: BELOW 3.0 VOLTS (MULFUNCTION INDICATOR LAMP ON)
9.0±14.0 VOLTS (MULFUNCTION INDICATOR LAMP OFF AND ENGINE RUNNING)
A/C ± E1: BELOW 1.5 VOLTS (ENGINE IDLING AND A/C SW ON)
7.5±14.0 VOLTS (A/C SW OFF)
ACT ± E1:9.0±14.0 VOLTS (ENGINE IDLING AND A/C SW ON)
BELOW 1.5 VOLTS (A/C SW OFF)
ACIS ± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
STA ± E1:6.0 VOLTS OR MORE (ENGINE CRANKING)
I 4, I 5, I 6, I 7, I 8, I 9
INJECTOR1±2 : APPROX. 13.8 
T 1
THROTTLE POSITION SENSOR3±1 :0.2±5.7 KWITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0 MM (0 IN.)
2±1 : LESS THAN 2.3 KWITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0.5 MM (0.020 IN.)
WITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0.7 MM (0.0276 IN.)
3±1 :2.0±10.2 KWITH THROTTLE VALVE FULLY OPEN
SERVICE HINTS

94
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
E 7(C), E 8(B), E10(A) ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) (A/T)E11(C), E12(B), E14(A) ENGINE CONTROL MODULE (ENGINE ECU) (M/T)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E2:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
VC ± E2:4.5± 5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E2:0.3± 0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
:3.2± 4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
PIM ± E2:3.3± 3.9 VOLTS (IGNITION SW AT ON POSITION)
#10, #20 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (EX. CALIFORNIA)
#10, #20,
#30, #40 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (CALIFORNIA)
THA ± E2:0.5± 3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2± 1.0 VOLTS (IGNITION SW ON AND COOLANT TEMP. 80°C, 176°F)
STA ± E1:6.0±14.0 VOLTS (ENGINE CRANKING)
IGT ± E1: PULSE GENERATION (ENGINE CRANKING OR IDLING)
W ± E1:9.0±14.0 VOLTS (NO TROUBLE AND ENGINE RUNNING)
ACT ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
ACA ± E1:7.5±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW ON)
NSW ± E1:0± 3.0 VOLTS (IGNITION SW ON AND PARK/NEUTRAL POSITION SW (NEUTRAL START SW)
POSITION P OR N POSITION)
9.0±14.0 VOLTS (IGNITION SW ON AND EX. PARK/NEUTRAL POSITION SW
(NEUTRAL START SW) POSITION P OR N POSITION)
RESISTANCE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTORS
(DISCONNECT WIRING CONNECTOR)
IDL ± E2: INFINITY (THROTTLE VALVE OPEN)
2.3 KW OR LESS (THROTTLE VALVE FULLY CLOSED)
VTA ± E2:3.3 ±10.0 KW (THROTTLE VALVE FULLY OPEN)
0.2 ± 0.8 KW (THROTTLE VALVE FULLY CLOSED)
VC ± E2:3.0 ±7 0 KW
THA ± E2:2.0 ±3.0 KW (INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2 ±0.4 KW (COOLANT TEMP. 80°C, 176°F)
G1, NE ± G±:0.17±0.21 KW
ISCC, ISCO± +B, +B1:19.3±22.3 W
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1032E11A32J 133
C 832E12C32K 131
C 9A32E14B32M 131
C10C32F15A34 (S/D), 35 (C/P), 36 (W/G)N 131
D 130I 131O 231
D 230I 231O 331
D 332I 331T 131
D 632I 431V 131
E 130I 531V 231
E 430I 631V 331
E 7C32I 731V 531
E 8B32I1031
E10A32I1233
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
626R/B NO. 6 (BEHIND GLOVE BOX)
SERVICE HINTS

102
ENGINE CONTROL (5S±FE M/T EX. CALIFORNIA)
E11(A), E12(B), E14(C) ENGINE CONTROL MODULE (ENGINE ECU)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
PIM ± E2:3.3± 3.9 VOLTS (IGNITION SW AT ON POSITION)
#10, #20 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
THA ± E2:0.5± 3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2± 1.0 VOLTS (IGNITION SW ON AND COOLANT TEMP. 80°C, 176°F)
STA ± E1:6.0±14.0 VOLTS (ENGINE CRANKING)
IGT ± E1:0.8±1.2 VOLTS (ENGINE CRANKING OR IDLING)
ISCC, ISCO± E1:8.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
W ± E1:9.0±14.0 VOLTS (IGNITION SW ON, NO TROUBLE AND ENGINE RUNNING)
ACT ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
ACA ± E1:7.5±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW ON)
RESISTANCE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTORS
(DISCONNECT WIRING CONNECTOR)
IDL ± E1: INFINITY (THROTTLE VALVE OPEN)
0 W (THROTTLE VALVE FULLY CLOSED)
THA ± E2:2.0 ±3.0 KW (INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2 ±0.4 KW (COOLANT TEMP. 80°C, 176°F)
G+ ± G±:0.17±0.21 KW
ISCC, ISCO± +B, +B1:19.3±22.3 KW
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1032E14C30K 131
C 832F1534 (S/D), 35 (C/P), 36 (W/G)M 131
C 9A32I 131N 131
C10B32I 231O 231
D 130I 331O 331
D 230I 431T 131
D 332I 531V 131
D 632I 631V 231
E 130I 731V 331
E 430I1031V 531
E11A30I1233
E12B30J 133
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
626R/B NO. 6 (BEHIND GLOVE BOX)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1B
1C20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
1M
2A22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3A
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
SERVICE HINTS

174
SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
NOTICE: When inspecting or repairing the SRS (supplemental restraint system), perform the operation in
accordance with the following precautionary instructions and the procedure and precautions in the Repair
Manual for the applicable model year.

Malfunction symptoms of the supplemental restraint system are difficult to confirm, so the diagnostic trouble
codes become the most important source of information when troubleshooting.
When troubleshooting the supplemental restraint system, always inspect the diagnostic trouble codes before
disconnecting the battery.

Work must be started after 90 seconds from the time the Ignition SW is set to the ªLOCKº position and the
negative (±) terminal cable is disconnected from the battery.
(The supplemental restraint system is equipped with a back±up power source so that if work is started within
90 seconds of disconnecting the negative (±) terminal cable of the battery, the SRS may be activated.)
When the negative (±) terminal cable is disconnected from the battery, memory of the clock and audio systems
will be cancelled. So before starting work, make a record of the contents momorized by each memory system.
When work is finished, reset the clock and audio system as before and adjust the clock. This vehicle has tilt
and telescopic steering, power seat and outside rear view mirror and power shoulder belt anchorage, which
are all equipped with memory function, it is not possible to make a record of the customer, and ask the
customer to adjust the features and reset the memory.
To avoid erasing the memory of each memory system, never use a back±up power supply from outside the
vehicle.

When removing the steering wheel pad or handling a new steering wheel pad, keep the pad upper surface
facing upward. Also, lock the lock lever of the twin lock type connector at the rear of the pad and take care
not to damage the connector.
(Storing the pad with its metallic surface up may lead to a serious accident if the SRS inflates for some reason.)

Store the steering wheel pad where the ambient temperature remains below 93°C (200°F), without high
humidity and away from electrical noise.

Never use SRS parts from another vehicle. When replacing SRS parts, replace them with new parts.

Never disassemble and repair the steering wheel pad, center SRS sensor assembly or front airbag sensors.

Before repairing the body, remove the airbag sensors if during repair shocks are likely to be applied to the
sensors due to vibration of the body or direct tapping with tools or other parts.

Do not reuse a steering wheel pad or front airbag sensors.
After evaluating whether the center airbag sensor assembly is damaged or not, decide whether or not to reuse
it. (See the Repair Manual for the method for evaluating the center airbag sensor assembly.)

When troubleshooting the supplemental restraint system, use a high±impedance (Min. 10k
/V) tester.

The wire harness of the supplemental restraint system is integrated with the cowl wire harness assembly and
engine wire harness assembly.
The vehicle wiring harness exclusively for the airbag system is distinguished by corrugated yellow tubing, as
are the connectors.

Do not measure the resistance of the airbag squib.
(It is possible this will deploy the airbag and is very dangerous.)

If the wire harness used in the supplemental restraint system is damaged, replace the whole wire harness
assembly.
When the connector to the airbag front sensors can be repaired alone (when there is no damage to the wire
harness), use the repair wire specially designed for the purpose.
(Refer to the Repair Manual for the applicable Model year for details of the replacement method.)

INFORMATION LABELS (NOTICES) are attached to the periphery of the SRS components. Follow the
instructions on the notices.