1994 TOYOTA CAMRY park neutral sw

76
CHARGING
A
IG L S B
IC RE GULATOR2C 6
B 2B1B3 8
E9
E
IP3 10 IP 3 2GE 64)
A 1 7. 5A
ALT±S
R±LY
W
R±L
YB±O
W B
W
W
GENERATOR
(
ALTERNATOR)
BATTERY FL MAIN
2. 0L
100A ALT
CHARGE WARNING LIGHT
[COMB. METER]
JUNCTION
CONNECTOR
Y
J1
G1 , G2
C9
B FUSE BOX
FROM DAYTIME RUNNING
LIGHT RELAY(
MAIN)
Y E
(
CANADA)
R±L R±L
TO BA CK± UP SW(
M/T)
TO PARK/NEUTRAL POSITION
SW(
NEUTRAL START SW)(
A/T)
TO VEHICLE SPEED SENSOR
(
SPEED SENSOR) B 1A 1
C 1(
1MZ±FE)
(
5S±FE)
B F10 , F10AC,F16
I18
1D 61D37. 5A
IGN 10A
GAUGE
FROM POWER SOURCE SYSTEM(
SEE PA

78
ENGINE CONTROL (1MZ±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) AND
MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE ENGINE CONTROL IS
EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL CIRCUIT
THE ENGINE COOLANT TEMP. SENSOR (WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE WATER TEMP. IS INPUT INTO TERMINAL
THW OF ENGINE CONTROL MODULE (ECU) AS A CONTROL SIGNAL.
(2) INTAKE AIR TEMP. SIGNAL CIRCUIT
THE INTAKE AIR TEMP. SENSOR IS INSTALLED IN THE MASS AIR FLOW (AIR FLOW METER) AND DETECTS THE INTAKE AIR
TEMP., WHICH IS INPUT AS A CONTROL SIGNAL TO TERMINAL THA OF ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OXL, OXR
AND OXS OF THE ENGINE CONTROL MODULE (ECU). TO MAINTAIN STABLE DETECTION PERFORMANCE BY THE OXYGEN
SENSOR, A HEATER IS USED FOR WARMING THE SENSOR. THE HEATER IS ALSO CONTROLLED BY THE ENGINE CONTROL
MODULE (ECU) (HTL, HTR AND HTS).
(4) RPM SIGNAL SYSTEM
CAMSHAFT POSITION AND CRANKSHAFT POSITION ARE DETECTED BY THE CAMSHAFT POSITION SENSOR AND
CRANKSHAFT POSITION SENSOR. CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINAL G22+ OF THE
ENGINE CONTROL MODULE (ECU), AND ENGINE RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL CIRCUIT
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE AS A CONTROL SIGNAL, WHICH IS
INPUT INTO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU). WHEN THE VALVE IS COMPLETELY CLOSED, THE
CONTROL SIGNAL IS INPUT INTO TERMINAL IDL.
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SP1 OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION IS IN NEUTRAL OR
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TEMRINAL A/C OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS +B
AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY.
(10) INTAKE AIR VOLUME SIGNAL CIRCUIT
INTAKE AIR VOLUME IS DETECTED BY THE MASS AIR FLOW (AIR FLOW METER) AND THE SIGNAL IS INPUT TO TERMINAL VG
OF THE ENGINE CONTROL MODULE (ECU). AS A CONTROL SIGNAL.
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY THE KNOCK SENSOR NO. 1 AND NO. 2 AND THE SIGNALS ARE INPUT INTO TERMINALS
KNKR AND KNKL AS A CONTROL SIGNAL.
SYSTEM OUTLINE

88
ENGINE CONTROL (5S±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE ECU (M/T), ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU (A/T)) AND MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE
ENGINE CONTROL IS EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL SYSTEM
THE ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE ENGINE COOLANT TEMP. (WATER TEMP.)
THUS THE ENGINE COOLANT TEMP. (WATER TEMP.) IS INPUT IN THE FORM OF A CONTROL SIGNAL TO TERMINAL THW OF
THE ENGINE CONTROL MODULE (ECU).
(2) INTAKE AIR TEMP. SIGNAL SYSTEM
THE INTAKE AIR TEMP. SENSOR (IN±AIR TEMP. SENSOR) IS DETECTS THE INTAKE AIR TEMP., WHICH IS INPUT AS A
CONTROL SIGNAL TO TERMINAL THA OF THE ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OX1 AND
OX2 OF THE ENGINE CONTROL MODULE (ECU).
(4) RPM SIGNAL SYSTEM
CRANKSHAFT POSITION AND ENGINE RPM ARE DETECTED BY THE PICK±UP COIL INSTALLED INSIDE THE DISTRIBUTOR.
CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINALS G+ AND G2 (CALIFORNIA), OF THE ENGINE
CONTROL MODULE (ECU), AND RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL SYSTEM
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE, WHICH IS INPUT AS A CONTROL
SIGNAL TO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU), OR WHEN THE VALVE IS FULLY CLOSED, TO
TERMINAL IDL
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SPD OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM (A/T)
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION ARE IN NEUTRAL AND
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TARMINAL ACA OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, THE VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS
+B AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY. THE CURRENT FLOWING THROUGH THE IGN FUSE
FLOWS TO TERMINAL IGSW OF THE ENGINE CONTROL MODULE (ECU).
(10) INTAKE AIR VOLUME SIGNAL SYSTEM
INTAKE AIR VOLUME IS DETECTED BY THE MANIFOLD ABSOLUTE PRESSURE SENSOR (VACUUM SENSOR) (FOR MANIFOLD
PRESSURE) AND IS INPUT AS A CONTROL SIGNAL TO TERMINAL PIM OF THE ENGINE CONTROL MODULE (ECU).
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR AND THE SIGNAL IS INPUT INTO TERMINAL KNK AS A CONTROL
SIGNAL.
(13) ELECTRICAL LOAD SIGNAL SYSTEM
THE SIGNAL WHEN SYSTEMS SUCH AS THE REAR WINDOW DEFOGGER, HEADLIGHTS, ETC. WHICH CAUSE A HIGH
ELECTRICAL BURDEN ARE ON IS INPUT TO TERMINAL ELS AS A CONTROL SIGNAL.
SYSTEM OUTLINE

90
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
CB
IG2
ACC
IG1 ST2AM2
AM1
ST1
7 9
1 2
1 2
1 2
1 2 E20
E20
E20I20
I23 E20 E18 E18 E17E17
I18
EBA 1A 12
A 22 C 11 C12A23 C 7 IP 3 12
1 2
2 1 2D 2
2B 22C3
W±B
B±W B±WY
B±W
Y WW±R
W±R
W±R
W±RW±R W±R W±R W±R B±O
B±W
B±O
W±G
B±O B±O
B±O B±O B±OLG
G W±L W±B B±W
W±R
B±O B±O B±O W±R
B±O B±O B±O
B±O
7. 5A
IGN
IP1 18
B±O
#20 #10 NSWBATT EGRISCV +B 15A
EFI
EFI MAIN
RELAY
VSV
(
FOR EGR) VSV
(
FOR A/C IDLE±UP)
E NGINE CONTROL MODULE(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION ECU)(
A/T)
INJE CTOR NO. 1
INJE CTOR NO. 3
INJE CTOR NO. 2
INJE CTOR NO. 4 I4
I5
I6
I7
E7 , E8 , E10C
V2 V1
W±R
I12
IGNITION SW
C 9C10 31 2
B±O
G±Y G±R
ISCC ISCO
IDLE AIR CONTROL
VALVE
(
ISC VALVE) I1
FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
34 13
IP1 11
IP1 9
W±R
B±O (
*4) (
*5)
TO PARK/NEUTRAL POSITION SW
(
NEUTRAL STA RT SW) 2D 4IP116
W±R
I2 C 24#40
I18C 25#30
W W(
*1)
(
*2)
(
*2)
Y
(
*2)
Y
(
*1)
R±B(
*1)
(
*2)
Y(
*1)
W(
*2)
W(
*1)
R±L(
*1)
B±W
(
*5)
E17
B±O B±O
(
*2)
(
*1) (
*1)
B±O
(
*1)
12
25(
*1)
(
*2)
(
*1)
(
*2)
B±W
W
(
*2)
(
EX. CALIFORNIA M/T)
(
EX. CALIFORNIA M/T)B E11 , E12CA,E14E NGINE CONTROL MODULE(
ENGINE ECU)(
M/T)
I21
B±W
(
*4)
B±W
1A 61G 8
1D 9
1G 61E 51A14

92
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
CB
A
321
C
1 78
C
A 6
B 3
A 21 A10 C13 C26 B13A 5
EDI13G±R R±L R±L
G±R
G±R
Y±G G±WBR LG±B
B±Y
W W±B W±B
W±R
B±O
B±O
B
G±R B±O B±O W±R
R±W G±WY±G G±R
E1 TE2 TE1
WW
DATA LINK CONNECTOR 2
(
TDCL) FROM CE SYSTEM
(
SEE P
JUNCTION
CONNECTOR
MALFUNCTION INDICATOR
LAMP(
CHECK E NG INE
WARNING LIGHT)
[COMB. METER]
ACT ACA E01 E02 KNKENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)(
A/T)
ACT ACA
KNOCK
SENSOR A/C AMPLIFIER A1 0K1 E7 ,E8 ,E10
A
C9 , C10
J1D3
B
(
SHIELDED)
(
SHIELDED)
E16
O2
OXYGEN SENSOR
(
SUB)
1E15BR
BR
5TT
BR±B IP3 11 IP314
A 9 23
4 1
512IP3 2
SPEED
LGP G±B
G V±Y V±Y
R±L
R±L
SP1COMBINATION
METER C8
VEHICLE
SPEED SENSOR
(
SPEED SENSOR) V5
B
BR I13
G±R
G±R(
*5)
(
*4)
R±L
BR BR
1 2BR 7
R±W
ENG
BR
R±L
I18
R±L TO PARK/NEUTRAL POSITION
SW(
NEUTRAL START SW)
TO GENERATOR(
ALTERNATOR)
R±L
G±R(
*5)(
*4)
(
*3)
B E11 , E12CA,E14
ENGINE CONTROL MODULE(
ENGINE ECU)(
M/T) G±R
(
*
4)
1B 6 10A
GAUGE
1D6
3D 73D19
3D 18
3D 22
3D 10
3D 3
3D 12
POWER SOUR
AGE 64)

94
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
E 7(C), E 8(B), E10(A) ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) (A/T)E11(C), E12(B), E14(A) ENGINE CONTROL MODULE (ENGINE ECU) (M/T)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E2:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
VC ± E2:4.5± 5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E2:0.3± 0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
:3.2± 4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE OPEN)
PIM ± E2:3.3± 3.9 VOLTS (IGNITION SW AT ON POSITION)
#10, #20 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (EX. CALIFORNIA)
#10, #20,
#30, #40 ± E01, E02:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION) (CALIFORNIA)
THA ± E2:0.5± 3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2± 1.0 VOLTS (IGNITION SW ON AND COOLANT TEMP. 80°C, 176°F)
STA ± E1:6.0±14.0 VOLTS (ENGINE CRANKING)
IGT ± E1: PULSE GENERATION (ENGINE CRANKING OR IDLING)
W ± E1:9.0±14.0 VOLTS (NO TROUBLE AND ENGINE RUNNING)
ACT ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
ACA ± E1:7.5±14.0 VOLTS (IGNITION SW ON AND AIR CONDITIONING ON)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW ON)
NSW ± E1:0± 3.0 VOLTS (IGNITION SW ON AND PARK/NEUTRAL POSITION SW (NEUTRAL START SW)
POSITION P OR N POSITION)
9.0±14.0 VOLTS (IGNITION SW ON AND EX. PARK/NEUTRAL POSITION SW
(NEUTRAL START SW) POSITION P OR N POSITION)
RESISTANCE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTORS
(DISCONNECT WIRING CONNECTOR)
IDL ± E2: INFINITY (THROTTLE VALVE OPEN)
2.3 KW OR LESS (THROTTLE VALVE FULLY CLOSED)
VTA ± E2:3.3 ±10.0 KW (THROTTLE VALVE FULLY OPEN)
0.2 ± 0.8 KW (THROTTLE VALVE FULLY CLOSED)
VC ± E2:3.0 ±7 0 KW
THA ± E2:2.0 ±3.0 KW (INTAKE AIR TEMP. 20°C, 68°F)
THW ± E2:0.2 ±0.4 KW (COOLANT TEMP. 80°C, 176°F)
G1, NE ± G±:0.17±0.21 KW
ISCC, ISCO± +B, +B1:19.3±22.3 W
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1032E11A32J 133
C 832E12C32K 131
C 9A32E14B32M 131
C10C32F15A34 (S/D), 35 (C/P), 36 (W/G)N 131
D 130I 131O 231
D 230I 231O 331
D 332I 331T 131
D 632I 431V 131
E 130I 531V 231
E 430I 631V 331
E 7C32I 731V 531
E 8B32I1031
E10A32I1233
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
626R/B NO. 6 (BEHIND GLOVE BOX)
SERVICE HINTS

152
BACK±UP LIGHT
IP3 2
8 2
1 2
IP3 1
Bd2 3IJ1 10
B38
BR FROM POWER SOURCE SYSTEM(
SEEPAGE64)
R±L
R±B
R±B
R±L R±L R±B R±B R±B R±B R±B W±B
BACK±UP
LIGHT SW BACK±UP LIGHT SW
[PARK/NEUTRAL
POSITION SW
(
NEUTRAL START SW)
]B1 P1(
M/T)
(
A/T)
(
M/T)(
A/T)
Bc2 6
R±B
W±BBa1 3
B16
B16 Ba 14
BL W±BR±B
W±B R±B
W±B W±B
R±B R±B(
W/G)
(
S/D, C/P)
(
S /D, C/P) (
S/D, W/G) (
W/G)(
W/G)
(
S/D, C/P)
(
W/G)(
S /D, C/P)
(
W/G)R±L
(
A/T)
R±L TO VEHICLE SPEED SENSOR
(
SPEED SENSOR)
TO GENERATOR(
ALTERNATOR)TO VEHICLE SPEED SENSOR
(
SPEED SENSOR)
TO GE NERATOR(
ALTERNATOR) R±L
R±L
(
M/T)
(
A/T)
(
M/T)
I18
I18
B 3A 4
B 3A 4 (
S/D, C/P)
(
W/G)(
S/D, C/P)
(
W/G)
A 3A3
B 4 B 4(
S/D, C/P)
(
W/G) (
S/D, C/P)
(
W/G)B R9 ,A
BA CK ±UP LIGHT LH
[REAR COMB. LIGHT LH]B R11 ,A
BACK±UP LIGHT RH
[REAR COMB. LIGHT RH]
1D 610A
GAUGE

153
B 1 BACK±UP LIGHT SW
2±1 : CLOSED WITH SHIFT LEVER IN R POSITION
P 1 BACK±UP LIGHT SW [PARK/NEUTRAL POSITION SW (NEUTRAL START SW)]
6±5 : CLOSED WITH SHIFT LEVER IN R POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 130R 934 (S/D), 35 (C/P), 36 (W/G)
P 129 (1MZ±FE), 31 (5S±FE)R1134 (S/D), 35 (C/P), 36 (W/G)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
IP344ENGINE WIRE AND COWL WIRE
Ba146 (S/D)FLOOR NO 1 WIRE AND LUGGAGE ROOM NO 2 WIREBa148 (C/P)FLOOR NO. 1 WIRE AND LUGGAGE ROOM NO. 2 WIRE
Bc250 (W/G)BACK DOOR NO. 1 WIRE AND FLOOR NO. 1 WIRE
Bd250 (W/G)BACK DOOR NO. 1 WIRE AND BACK DOOR NO. 2 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
46 (S/D)
BL48 (C/P)UNDER THE LEFT QUARTER PILLARBL
50 (W/G)
UNDER THE LEFT QUARTER PILLAR
BR50 (W/G)BACK DOOR CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I1844ENGINE WIREB3850 (W/G)BACK DOOR NO. 2 WIRE
B1646 (S/D)LUGGAGE ROOM NO. 2 WIRE
34 B1 P 1 ,GRAY GRAY
12X2
8B R9 ,ABR11 ,A
SERVICE HINTS