1994 TOYOTA CAMRY combination

66
POWER SOURCE
TAILLIGHT RELAY5±3 : CLOSED WITH LIGHT CONTROL SW AT TAIL OR HEAD POSITION
CLOSED WITH ENGINE RUNNING AND PARKING BRAKE LEVER RELEASED (CANADA)
ENGINE MAIN RELAY4±5 : CLOSED WITH IGNITION SW AT ON OR ST POSITIONHEADLIGHT RELAY2±1 : CLOSED WITH LIGHT CONTROL SW AT HEAD POSITION OR DIMMER SW AT FLASH POSITION
CLOSED WITH ENGINE RUNNING AND PARKING BRAKE LEVER RELEASED (CANADA)
I12
IGNITION SW 4±3 : CLOSED WITH IGNITION KEY AT ACC OR ON POSITION
10±9, 4±2 : CLOSED WITH IGNITION KEY AT ON OR ST POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
F10A28F17E28 (1MZ±FE), 30 (5S±FE)I 233F10B30F18D28 (1MZ±FE), 30 (5S±FE)
F16C28 (1MZ±FE), 30 (5S±FE)G 128 (1MZ±FE), 30 (5S±FE)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 4 (LEFT KICK PANEL)
425R/B NO. 4 (RIGHT KICK PANEL)
526R/B NO. 5 (ENGINE COMPARTMENT LEFT)
727R/B NO. 7 (NEAR THE BATTERY)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1C
1E20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2B22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2F22COWL WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3A24COWL WIRE AND J/B NO 3 (BEHIND COMBINATION METER)3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EB138 (1MZ±FE)ENGINE ROOM MAIN WIRE AND RELAY WIREEB140 (5S±FE)ENGINE ROOM MAIN WIRE AND RELAY WIRE
EC138 (1MZ±FE)ENGINE WIRE AND ENGINE ROOM MAIN WIREEC140 (5S±FE)ENGINE WIRE AND ENGINE ROOM MAIN WIRE
EF138 (1MZ±FE)EF140 (5S±FE)ENGINE WIRE AND COWL WIREIP144
ENGINE WIRE AND COWL WIRE
IP344
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB38 (1MZ±FE)FRONT LEFT FENDEREB40 (5S±FE)FRONT LEFT FENDER
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E638 (1MZ±FE)E1438 (1MZ±FE)E 640 (5S±FE)ENGINE ROOM MAIN WIREE15ENGINE WIRE
E738 (1MZ±FE)ENGINE ROOM MAIN WIREE2040 (5S±FE)ENGINE WIRE
E 740 (5S±FE)E23
40 (5S FE)
E1038 (1MZ±FE)ENGINE WIREI 244COWL WIRE
SERVICE HINTS

70
STARTING AND IGNITION (1MZ±FE)
I12 IGNITION SW
4±7 : CLOSED WITH IGNITION SW AT ST POSITION
10±9 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
STARTER RELAY
(6) 2± (6) 4 : CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION (M/T)
CLOSED WITH IGNITION SW AT ST POSITION (A/T)
STARTER
POINTS CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION
P 1 PARK/NEUTRAL POSITION SW (NEUTRAL START SW) (A/T)
2±3 : CLOSED WITH A/T SHIFT LEVER IN P OR N POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
D 128I15B29I2129
E 732I1629J 733
F10A28I1729P 129
F16B28I1829S 3A29
I 2A29I1929S 4B29
I1233I2029
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C
1E20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1G20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2F22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)EF140 (5S±FE)ENGINE WIRE AND COWL WIRE
IP144
ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC38 (1MZ±FE)INTAKE MANIFOLD RHEC40 (5S±FE)INTAKE MANIFOLD RH
ED38 (1MZ±FE)INTAKE MANIFOLD LHED40 (5S±FE)INTAKE MANIFOLD LH
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1038 (1MZ FE)ENGINE WIREE1338 (1MZ FE)ENGINE WIREE1238 (1MZ±FE)ENGINE WIREE1438 (1MZ±FE)ENGINE WIRE
SERVICE HINTS

74
STARTING AND IGNITION (5S±FE)
I12 IGNITION SW
4±7 : CLOSED WITH IGNITION SW AT ST POSITION
10±9 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
C 7 CLUTCH START SW (M/T)
1±2 : CLOSED WITH CLUTCH PEDAL FULLY DEPRESSED
STARTER RELAY
(6) 2± (6) 4 : CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION (M/T)
CLOSED WITH IGNITION SW AT ST POSITION (A/T)
STARTER
POINTS CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION
P 1 PARK/NEUTRAL POSITION SW (NEUTRAL START SW) (A/T)
2±3 : CLOSED WITH A/T SHIFT LEVER IN P OR N POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 732E11B32I1233
D 130F10A30P 131
D2A30F16B30S 3A31D 2B30I 231S 4B31
E 7A32I 331
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1C
1E20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2F22COWL WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3B
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)EF140 (5S±FE)ENGINE WIRE AND COWL WIRE
IP144
ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC38 (1MZ±FE)INTAKE MANIFOLD RHEC40 (5S±FE)INTAKE MANIFOLD RH
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1640 (5S FE)ENGINE WIREE2040 (5S±FE)ENGINE WIRE
E1940 (5S±FE)ENGINE WIRE
SERVICE HINTS

78
ENGINE CONTROL (1MZ±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) AND
MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE ENGINE CONTROL IS
EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL CIRCUIT
THE ENGINE COOLANT TEMP. SENSOR (WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE WATER TEMP. IS INPUT INTO TERMINAL
THW OF ENGINE CONTROL MODULE (ECU) AS A CONTROL SIGNAL.
(2) INTAKE AIR TEMP. SIGNAL CIRCUIT
THE INTAKE AIR TEMP. SENSOR IS INSTALLED IN THE MASS AIR FLOW (AIR FLOW METER) AND DETECTS THE INTAKE AIR
TEMP., WHICH IS INPUT AS A CONTROL SIGNAL TO TERMINAL THA OF ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OXL, OXR
AND OXS OF THE ENGINE CONTROL MODULE (ECU). TO MAINTAIN STABLE DETECTION PERFORMANCE BY THE OXYGEN
SENSOR, A HEATER IS USED FOR WARMING THE SENSOR. THE HEATER IS ALSO CONTROLLED BY THE ENGINE CONTROL
MODULE (ECU) (HTL, HTR AND HTS).
(4) RPM SIGNAL SYSTEM
CAMSHAFT POSITION AND CRANKSHAFT POSITION ARE DETECTED BY THE CAMSHAFT POSITION SENSOR AND
CRANKSHAFT POSITION SENSOR. CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINAL G22+ OF THE
ENGINE CONTROL MODULE (ECU), AND ENGINE RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL CIRCUIT
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE AS A CONTROL SIGNAL, WHICH IS
INPUT INTO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU). WHEN THE VALVE IS COMPLETELY CLOSED, THE
CONTROL SIGNAL IS INPUT INTO TERMINAL IDL.
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SP1 OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION IS IN NEUTRAL OR
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TEMRINAL A/C OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS +B
AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY.
(10) INTAKE AIR VOLUME SIGNAL CIRCUIT
INTAKE AIR VOLUME IS DETECTED BY THE MASS AIR FLOW (AIR FLOW METER) AND THE SIGNAL IS INPUT TO TERMINAL VG
OF THE ENGINE CONTROL MODULE (ECU). AS A CONTROL SIGNAL.
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY THE KNOCK SENSOR NO. 1 AND NO. 2 AND THE SIGNALS ARE INPUT INTO TERMINALS
KNKR AND KNKL AS A CONTROL SIGNAL.
SYSTEM OUTLINE

83
AB
A
EC 1 C 5
TE 1D 11
TE2
B 14KNKL
B 16G22+
B 5NE +
EE1 4EE12
1 1
BR
B
B±O
L±B
BR GR±B
WB
B±W
R R B±W
3 1 12 19
8FP +B IG±
SG
TE 2 TE 1 DATA LINK CONNECTOR
1(
CHECK CONNECTOR) D1
V5
CRANKSHAFT POSITION
SENSOR C18KNOCK SENSOR 2 K2
CAMSHAFT POSITION
SENSOR C17
C 3
G±R
6B 3
G±R
A
W
(
SHIELDED) (
SHIELDED)
D 12FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
C CIP3 2
IP2 11 IP2141
23
4 512 SP1G±B
GLGP
R±LR±L
R±L
VEHICLE SPEED
SENSOR
(
SPEED SENSOR)
B
MALFUNCTION INDICATOR LAMP
(
CHECK ENGINE WARNING LIGHT)
[COMB. METER] C9 , C10
SPEED
JUNCTION
CONNECTOR J2 COMBINATION
METER C8
D
E NG INE CO NTROL MODULE(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION ECU) E7 , E8 ,E9 ,E10C
E142 1
NOISE FILTER
(
FOR IGNITION
SYSTEM) W±B
W±B B±O
W±B
N1
V±Y
ED B±OR±L
R±L B
I23
D 28
SDL DA TA LINK
CO NNE CTOR 3 D24 FROM POWER
SO TEM
(
S)
.5A
OBD
DA TA LINK
CO NNE CTO R
2(
TDCL) D3
IP3 16 IP1 1
22I18 I18B 6NE±
C E1
I18 IM12
J1
J UNCTION CO NNE CTO R
IE JUNCTION
CONNECTOR J7
L
G
BR
V±Y L
G
V±Y
BR BR W±B
W±B
BR
BR
BR BR BR BR
G (
SHIELDED)
(
SHIELDED)
(
SHIELDED)
(
SHIELDED)
A
A
A
AA
A
A
A
A
A
A
BR
BR
BR
BR
BR
W±B BR
BR
BRBR
(
SHIELDED)
(
SHIELDED) BR BR
BR
BR BR W±B
F F
24 15
2 45
G± WBR W±B
L±B
B±O
BR
BR
BR
BR BB G±W
W3
E1
OX1
SDL
16W±BE1
CG
OX2
BATT(
SHIELDED)
(
SHIELDED) BR
(
SHIELDED)
(
SHIELDED)
(
SHIELDED)
(
SHIELDED)
16 B 17G22±IP1 19
G±R
10A
GAUGE
1B 616
R± L
D
3D 3
3D 12
3D 183D 7
3D 3
3D 22
3D 10
1M5
1C8
URCE SYS
EE PAGE 64
7

85
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 832F16B28I2029
C 9A32H 9D33I2129
C10B32H1128J 133
C1728H1228J 233
C1828I 129J 639
D 128I 2A29J 733
D 332I 428K 129
D 632I 529K 229
D2432I 629M 629
E 128I 729N 129
E 428I 829T 129
E 7A32I 929V 129
E 8B32F15B29V 229
E 9C32I1629V 329
E10D32I1729V 429
F10A28I1829V 529
F1530I1929
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
626R/B NO. 6 (BEHIND GLOVE BOX)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1B
1C
1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1E
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
1M
2B22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2C22ENGINE WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2D22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3A
3B24COWL WIRE AND J/B NO 3 (BEHIND COMBINATION METER)3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EE140 (1MZ±FE)ENGINE WIRE AND SENSOR WIRE
EF138 (1MZ±FE)ENGINE WIRE AND COWL WIRE
II142COWL WIRE AND INSTRUMENT PANEL WIRE
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
IM142INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE
IP1
IP244ENGINE WIRE AND COWL WIRE
IP3
44ENGINE WIRE AND COWL WIRE
IQ144ENGINE WIRE AND INSTRUMENT PANEL WIRE
46 (S/D)
BX148 (C/P)FUEL GAUGE WIRE AND FLOOR NO. 1 WIREBX1
50 (W/G)
FUEL GAUGE WIRE AND FLOOR NO. 1 WIRE

88
ENGINE CONTROL (5S±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE ECU (M/T), ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU (A/T)) AND MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE
ENGINE CONTROL IS EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL SYSTEM
THE ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE ENGINE COOLANT TEMP. (WATER TEMP.)
THUS THE ENGINE COOLANT TEMP. (WATER TEMP.) IS INPUT IN THE FORM OF A CONTROL SIGNAL TO TERMINAL THW OF
THE ENGINE CONTROL MODULE (ECU).
(2) INTAKE AIR TEMP. SIGNAL SYSTEM
THE INTAKE AIR TEMP. SENSOR (IN±AIR TEMP. SENSOR) IS DETECTS THE INTAKE AIR TEMP., WHICH IS INPUT AS A
CONTROL SIGNAL TO TERMINAL THA OF THE ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OX1 AND
OX2 OF THE ENGINE CONTROL MODULE (ECU).
(4) RPM SIGNAL SYSTEM
CRANKSHAFT POSITION AND ENGINE RPM ARE DETECTED BY THE PICK±UP COIL INSTALLED INSIDE THE DISTRIBUTOR.
CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINALS G+ AND G2 (CALIFORNIA), OF THE ENGINE
CONTROL MODULE (ECU), AND RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL SYSTEM
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE, WHICH IS INPUT AS A CONTROL
SIGNAL TO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU), OR WHEN THE VALVE IS FULLY CLOSED, TO
TERMINAL IDL
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SPD OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM (A/T)
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION ARE IN NEUTRAL AND
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TARMINAL ACA OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, THE VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS
+B AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY. THE CURRENT FLOWING THROUGH THE IGN FUSE
FLOWS TO TERMINAL IGSW OF THE ENGINE CONTROL MODULE (ECU).
(10) INTAKE AIR VOLUME SIGNAL SYSTEM
INTAKE AIR VOLUME IS DETECTED BY THE MANIFOLD ABSOLUTE PRESSURE SENSOR (VACUUM SENSOR) (FOR MANIFOLD
PRESSURE) AND IS INPUT AS A CONTROL SIGNAL TO TERMINAL PIM OF THE ENGINE CONTROL MODULE (ECU).
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR AND THE SIGNAL IS INPUT INTO TERMINAL KNK AS A CONTROL
SIGNAL.
(13) ELECTRICAL LOAD SIGNAL SYSTEM
THE SIGNAL WHEN SYSTEMS SUCH AS THE REAR WINDOW DEFOGGER, HEADLIGHTS, ETC. WHICH CAUSE A HIGH
ELECTRICAL BURDEN ARE ON IS INPUT TO TERMINAL ELS AS A CONTROL SIGNAL.
SYSTEM OUTLINE

92
ENGINE CONTROL (5S±FE A/T AND CALIFORNIA M/T)
CB
A
321
C
1 78
C
A 6
B 3
A 21 A10 C13 C26 B13A 5
EDI13G±R R±L R±L
G±R
G±R
Y±G G±WBR LG±B
B±Y
W W±B W±B
W±R
B±O
B±O
B
G±R B±O B±O W±R
R±W G±WY±G G±R
E1 TE2 TE1
WW
DATA LINK CONNECTOR 2
(
TDCL) FROM CE SYSTEM
(
SEE P
JUNCTION
CONNECTOR
MALFUNCTION INDICATOR
LAMP(
CHECK E NG INE
WARNING LIGHT)
[COMB. METER]
ACT ACA E01 E02 KNKENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)(
A/T)
ACT ACA
KNOCK
SENSOR A/C AMPLIFIER A1 0K1 E7 ,E8 ,E10
A
C9 , C10
J1D3
B
(
SHIELDED)
(
SHIELDED)
E16
O2
OXYGEN SENSOR
(
SUB)
1E15BR
BR
5TT
BR±B IP3 11 IP314
A 9 23
4 1
512IP3 2
SPEED
LGP G±B
G V±Y V±Y
R±L
R±L
SP1COMBINATION
METER C8
VEHICLE
SPEED SENSOR
(
SPEED SENSOR) V5
B
BR I13
G±R
G±R(
*5)
(
*4)
R±L
BR BR
1 2BR 7
R±W
ENG
BR
R±L
I18
R±L TO PARK/NEUTRAL POSITION
SW(
NEUTRAL START SW)
TO GENERATOR(
ALTERNATOR)
R±L
G±R(
*5)(
*4)
(
*3)
B E11 , E12CA,E14
ENGINE CONTROL MODULE(
ENGINE ECU)(
M/T) G±R
(
*
4)
1B 6 10A
GAUGE
1D6
3D 73D19
3D 18
3D 22
3D 10
3D 3
3D 12
POWER SOUR
AGE 64)