1994 TOYOTA CAMRY Cruise control

194
CRUISE CONTROL
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 228 (1MZ±FE), 30 (5S±FE)D 532N 3B33
C 8B32E 7A32P 129 (1MZ±FE), 31 (5S±FE)
C 9A32E 8C32P 233
C1332E10B32P 333
C1532E14C32S1033
C1632I1233V 529 (1MZ±FE), 31 (5S±FE)
D 128 (1MZ±FE), 30 (5S±FE)J 133
D 332N 2A33
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1B
1C
1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1E
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
1M
2B22ENGINE ROOM MAIN WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3B
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)ENGINE WIRE AND COWL WIREEF140 (5S±FE)ENGINE WIRE AND COWL WIRE
II142COWL WIRE AND INSTRUMENT PANEL WIRE
IP144ENGINE WIRE AND COWL WIREIP344ENGINE WIRE AND COWL WIRE
IR144ENGINE ROOM MAIN WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB38 (1MZ±FE)FRONT LEFT FENDEREB40 (5S±FE)FRONT LEFT FENDER
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I1344COWL WIREI2344COWL WIRE
I1844ENGINE WIRE

196
CRUISE CONTROL
CURRENT IS APPLIED AT ALL TIMES THROUGH STOP FUSE TO TERMINAL 1 OF THE CRUISE CONTROL ECU AND TERMINAL 2 OF
STOP LIGHT SW, AND ALSO THROUGH THE STOP FUSE TO TERMINAL 15 OF CRUISE CONTROL ECU.
WITH THE IGNITION SW TURNED TO ON, THE CURRENT FLOWS THROUGH GAUGE FUSE TO TERMINAL (A) 6 OF COMBINATION
METER AND THE CURRENT THROUGH ECU±IG FUSE FLOWS TO TERMINAL 14 OF CRUISE CONTROL ECU.
WHEN THE IGNITION SW IS ON AND THE CRUISE CONTROL MAIN SW IS TURNED ON, A SIGNAL IS INPUT FROM TERMINAL 15 OF
CRUISE CONTROL MAIN SW TO TERMINAL 4 OF CRUISE CONTROL ECU. AS A RESULT, THE CRUISE CONTROL ECU FUNCTIONS
AND THE CURRENT TO TERMINAL 14 OF CRUISE CONTROL ECU TO TERMINAL 13 OF CRUISE CONTROL ECU " GROUND, AND
THE CRUISE CONTROL SYSTEM IS IN A CONDITION READY FOR OPERATION.
AT THE SAME TIME, THE CURRENT THROUGH THE GAUGE FUSE FLOWS FROM TERMINAL (A) 6 OF CRUISE CONTROL INDICATOR
LIGHT " TERMINAL (B) 9 " TERMINAL 5 OF CRUISE CONTROL ECU " TERMINAL 13 " TO GROUND, CAUSING THE CRUISE
CONTROL INDICATOR LIGHT TO LIGHT UP, INDICATING THAT THE CRUISE CONTROL IS READY FOR OPERATION.
1. SET OPERATION
WHEN THE CRUISE CONTROL MAIN SW IS TURNED ON AND THE SET SW IS TURNED ON WITH THE VEHICLE SPEED WITHIN THE
SET LIMIT (APPROX. 40 KM/H, 25 MPH TO 200 KM/H, 124 MPH), A SIGNAL IS INPUT TO TERMINAL 18 OF THE CRUISE CONTROL ECU
AND THE VEHICLE SPEED AT THE TIME THE SET SW IS RELEASED IS MEMORIZED IN THE ECU AS THE SET SPEED.
2. SET SPEED CONTROL
DURING CRUISE CONTROL DRIVING, THE ECU COMPARES THE SET SPEED MEMORIZED IN THE ECU WITH THE ACTUAL VEHICLE
SPEED INPUT INTO TERMINAL 20 OF THE CRUISE CONTROL ECU FROM THE VEHICLE SPEED SENSOR (SPEED SENSOR), AND
CONTROLS THE CRUISE CONTROL ACTUATOR TO MAINTAIN THE SET SPEED.
WHEN THE ACTUAL SPEED IS LOWER THAN THE SET SPEED, THE ECU CAUSES THE CURRENT TO THE CRUISE CONTROL
ACTUATOR TO FLOW FROM TERMINAL 12" TERMINAL 6 OF CRUISE CONTROL ACTUATOR "TERMINAL 7 "TERMINAL 11 OF
CRUISE CONTROL ECU. AS A RESULT, THE MOTOR IN THE CRUISE CONTROL ACTUATOR IS ROTATED TO OPEN THE THROTTLE
VALVE AND THE THROTTLE CABLE IS PULLED TO INCREASE THE VEHICLE SPEED. WHEN THE ACTUAL DRIVING SPEED IS HIGHER
THAN THE SET SPEED, THE CURRENT TO CRUISE CONTROL ACTUATOR FLOWS FROM TERMINAL 11 OF ECU "TERMINAL 7 OF
CRUISE CONTROL ACTUATOR "TERMINAL 6 "TERMINAL 12 OF CRUISE CONTROL ECU.
THIS CAUSES THE MOTOR IN THE CRUISE CONTROL ACTUATOR TO ROTATE TO CLOSE THE THROTTLE VALVE AND RETURN THE
THROTTLE CABLE TO DECREASE THE VEHICLE SPEED.
3. COAST CONTROL
DURING THE CRUISE CONTROL DRIVING, WHILE THE COAST SW IS ON, THE CRUISE CONTROL ACTUATOR RETURNS THE
THROTTLE CABLE TO CLOSE THE THROTTLE VALVE AND DECREASE THE DRIVING SPEED. THE VEHICLE SPEED WHEN THE COAST
SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET SPEED.
4. ACCEL CONTROL
DURING CRUISE CONTROL DRIVING, WHILE THE ACCEL SW IS TURNED ON, THE CRUISE CONTROL ACTUATOR PULLS THE
THROTTLE CABLE TO OPEN THE THROTTLE VALVE AND INCREASE THE DRIVING SPEED.
THE VEHICLE SPEED WHEN THE ACCEL SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET
SPEED.
5. RESUME CONTROL
UNLESS THE VEHICLE SPEED FALLS BELOW THE MINIMUM SPEED LIMIT (APPROX. 40 KM/H, 25 MPH) AFTER CANCELING THE SET
SPEED BY THE CANCEL SW, PUSHING THE RESUME SW WILL CAUSE THE VEHICLE TO RESUME THE SPEED SET BEFORE
CANCELLATION.
6. MANUAL CANCEL MECHANISM
IF ANY OF THE FOLLOWING OPERATIONS OCCURS DURING CRUISE CONTROL OPERATION, CURRENT FLOW TO MAGNETIC
CLUTCH OF THE ACTUATOR IS CUT TURNS OFF AND THE MOTOR ROTATES TO CLOSE THE THROTTLE VALVE AND THE CRUISE
CONTROL IS RELEASED.
*PLACING THE SHIFT LEVER IN ªNº POSITION (PARK/NEUTRAL POSITION SW (NEUTRAL START SW ON). ªSIGNAL INPUT TO
TERMINAL 2 OF ECUº (A/T)
*DEPRESSING THE CLUTCH PEDAL (CLUCH SW ON). ªSIGNAL INPUT TO TERMINAL 2 OF THE ECUº (M/T)
*DEPRESSING THE BRAKE PEDAL (STOP LIGHT SW ON). ªSIGNAL INPUT TO TERMINAL 16 OF ECUº
*PUSH THE CANCEL SW (CANCEL SW ON). ªSIGNAL INPUT TO TERMINAL 18 OF ECUº
*DEPRESSING THE PARKING BRAKE PEDAL (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF ECUº (3VZ±FE)
*PULLING THE PARKING BRAKE LEVER (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF THE ECUº (5S±FE)
SYSTEM OUTLINE

197
7. AUTO CANCEL FUNCTION
A) IF ANY OF THE FOLLOWING OPERATING CONDITIONS OCCURS DURING CRUISE CONTROL OPERATION, THE SET SPEED IS
ERASED, CURRENT FLOW TO MAGNETIC CLUTCH IS CUT OFF AND THE CRUISE CONTROL IS RELEASED. (MAIN SW TURNS OFF).
WHEN THIS OCCURS, THE IGNITION SW MUST BE TURNED OFF ONCE BEFORE THE MAIN SW WILL TURN ON AGAIN.
*OVER CURRENT TO TRANSISTOR DRIVING MOTOR AND/OR MAGNETIC CLUTCH.
*WHEN CURRENT CONTINUED TO FLOW TO THE MOTOR INSIDE THE ACTUATOR IN THE THROTTLE VALVE ªOPENº DIRECTION.
*OPEN CIRCUIT IN MOTOR AND/OR MAGNETIC CLUTCH.
*MOMENTARY INTERRUPTION OF VEHICLE SPEED SIGNAL.
*SHORT CIRCUIT IN CRUISE CONTROL SW.
*MOTOR DOES NOT OPERATE DESPITE THE MOTOR DRIVE SIGNAL BEING OUTPUT.
B) IF ANY OF THE FOLLOWING CONDITIONS OCCURS DURING CRUISE CONTROL OPERATION, THE SET SPEED IS ERASED AND
THE CRUISE CONTROL IS RELEASED. CURRENT FLOW TO MAGNETIC CLUTCH IS CUT OFF UNTIL THE SET SW IS ªONº AGAIN.)
*WHEN THE VEHICLE SPEED HAS FALLEN BELOW THE MINIMUM SPEED LIMIT, APPROX. 40 KM/H (25 MPH)
*WHEN THE VEHICLE SPEED HAS FALLEN MORE THAN 16 KM/H (10 MPH) BELOW THE SET SPEED, E.G. ON AN UPWARD SLOPE.
*WHEN POWER TO THE CRUISE CONTROL SYSTEM IS MOMENTARILY CUT OFF.
C) IF ANY OF THE FOLLOWING CONDITIONS OCCURS DURING CRUISE CONTROL OPERATION, THE CRUISE CONTROL IS
RELEASED.
*OPEN CIRCUIT FOR TERMINAL 1 OF CRUISE CONTROL ECU.
8. AUTOMATIC TRANSMISSION CONTROL FUNCTION
*IN OVERDRIVE. IF THE VEHICLE SPEED BECOMES LOWER THAN THE OVERDRIVE CUT SPEED (SET SPEED MINUS APPROX. 4
KM/H, 2.5 MPH) DURING CRUISE CONTROL OPERATION, SUCH AS DRIVING UP A HILL, THE OVERDRIVE IS RELEASED AND THE
POWER INCREASED TO PREVENT A REDUCTION IN VEHICLE SPEED.
*AFTER RELEASING THE OVERDRIVE, IF VEHICLE SPEED BECOMES HIGHER THAN THE OVERDRIVE RETURN SPEED (SET
SPEED MINUS APPROX. 2 KM/H, 1.2 MPH) AND THE ECU JUDGES BY THE SIGNALS FROM POTENTIOMETER OF THE ACTUATOR
THAT THE UPWARD SLOPE HAS FINISHED, OVERDRIVE IS RESUMED AFTER A WHILE.
C 2 CRUISE CONTROL ACTUATOR
1±3 : APPROX. 2 K

5±4 : APPROX. 38

C13 CRUISE CNTROL SW MAIN [COMB. SW]
15±20 : CONTINUITY WITH MAIN SW ON
20±17 : APPROX. 418
WITH CANCEL SW ON
APPROX. 68
WITH RESUME/ACCEL SW ON
APPROX. 198
WITH SET/COAST SW ON
C16 CRUISE CONTROL ECU
14±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
1,15±GROUND : ALWAYS APPROX. 12 VOLTS
3±GROUND : CONTINUITY WITH PARKING BRAKE SW ON (ONE OF THE CANCEL SW) OR BRAKE LEVEL WARNING SW ON
20±GROUND :4 PULSE WITH 1 ROTATION OF ROTOR SHAFT
18±GROUND : APPROX. 418
WITH CANCEL SW ON IN CONTROL SW
APPROX. 68
WITH RES/ACC SW ON IN CONTROL SW
APPROX. 198
WITH SET/COAST SW ON IN CONTROL SW
13±GROUND : ALWAYS CONTINUITY
2±GROUND : CONTINUITY WITH SHIFT LEVER AT N POSITION (A/T) OR CLUTCH PEDAL DEPRESSED (M/T)
SERVICE HINTS

198
ELECTRONIC CONTROLLED TRANSMISSION AND A/T INDICATOR (1MZ±FE)
A
2D 22C32D4 2B 2
I23
I18
2 1
EBED IP 1 18 IP1 11 IP312
D 7 D 24 D 14 D 22 D 23
A 27 A11 A17 A33 B4
26FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
P±L P±LV L±Y W±B
B±O
B±OB±O
W±L
G±W G±W
Y±BW±GB±OR±Y
W±L Y±L W±BB±O
15A
EFI
SL S1 S2 E02 NC2± +B +B1 BATT STP OD1EFI MAIN
RELAY
FROM
CRUIS E CONTROL ECU
BR P±L
TO CRUISE
CONTROL ECU
15 23
O/D DIRECT CLUTCH
SPEED SENSOR O6STOP LIGHT SW
G±R
G±W
2 1
S10
B 1 A 2
B 2B1NOISE FILTER
(
FOR STOP LIGHT) N2 ,N3 A
G±W
G±R
B E7 ,E8AC,E9
ENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
B±O
D ,E10
A
3
ELECTRONIC CONTROLLED
TRANSMISSION SOLENOID E2 4 A
1
J UNCTION
CONNECTOR J7
A 3SLN±
Y±GB±O
B±OB±O
W±B
W±B
BR
A 34E01
A 28E03
A 16E1
B 9NC2+
Y±L
W±B
1D 91M3 7. 5A
IGN15A
STOP
1A 15
3B 43C 191M 6

199
3
3C
28D 6 C 1
234I6
I18 I18
C
D B 20 A32 B7B1B22
C 5D 6D 3
D 112 1
BRG±OR±L L±R R±L
L±R BR BR
GR±B G±W
G± OL±R B±Y L±WG
BR
BR
R±L R±L
L±R L±RL±R
G±O THW IDL VTA VCP E2
L±W
L±WII2 4
R±L ENGINE COOLANT TEMP.
SENSOR(
EFI WATER
TEMP. SENSOR)
FROM
CRUISE CONTROL ECU
THROTTLE POSITION
SENSORFROM POWER SOURCE SYSTEM(
SEE PAGE 64)
JUNCTION
CONNECTOR
POWER
NORMAL ELECTRONIC CONTROLLED
TRANSMISSION
PATTERN SELECT SW
TE 2 TE1OD2
E1 TE 2 TE1
DA TA LINK CONNECTOR 1
(
CHECK CONNECTOR)JUNCTION
CONNECTOR D 12
SPEED
IP3 11 IP314 5124
G±B
G
23
1 VEHICLE SPEED
SENSOR
(
SPEED SENSOR)
LGP
R±L SP1
COMBINATION
METER
V5C8 T1
J3
E6E4
J1
D1I18II1 6
L±R TO
COMBINATION
METERL±R
IN1 6IN13
R±L
B E7 ,E8
AC,E9
ENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
FROM
COOLING FAN ECU
L
D ,E10
IP 1 1
G± W
V±Y V±Y
AA
JUNCTION
CONNECTOR J7
BR
1K 81D6
3D 223D 10
10A
GAUGE

236
COMBINATION METER
AB
IJ1 5IJ111 IJ118
BX1 3 BX1 2 BX1 1 IP3 2
IP3 6
IP1 8IP 3 11 IP314
IP3 5
IP3 161
ED1 A 4
A 8A7A6A 5A12 B 11 B7B10 C 8C7C 4
123
23
4
1 I9
I9 C C
6 FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
R±L
R±L R±L R±L
BRY±L Y±R
BR BR BR Y±L Y±R Y±R
Y±L
BR
BR BR
B Y±G
BY±G
B
P
LG GG±B
G±B G±B
R±W
Y±B Y±BV±Y
R±L JUNCTION
CONNECTOR
BR
BR
FROM E NGINE CONTROL MODULE
(
E NGINE A ND E LE CTRONIC CONTROLLED
TRANSMISSION ECU)(
A/T)
FROM E NGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
FROM CRUISE CONTROL ECU
SPEEDFUEL
FUEL
WATER TEMP.
TA CHO
ABS
SEAT BELT
OIL
FUEL SENDER
WATER TEMP.
SENDER
IGNITER
VEHICLE SPEED
SENSOR
(
SPEED SENSOR)
TO AB S ECU
TO INTEGRATION
RELAY
OIL P RES SURE
SW
J2
B
W2
I2
V5
O1F1 5C
COMBINATION METER C8 ,C9 , C10
TO BACK±UP LIGHT SW(
M/T)
TO PARK/NEUTRAL POSITION SW
(
NEUTRAL START SW)(
A/T)
TO GENERA TOR(
ALTERNATOR) R±L
R±L
I18 6
TA C
COOLING FAN
ECU C14
BR
B
B JUNCTION CONNECTOR J7
(
*6) (
*6)
(
*7)A
A
(
*7)
(
*6)
1B 6 1D 610A
GAUGE
3D 13
3D 12
1D 121D 13
3C 133C 12

237
*
1 : W/O A/T INDICATOR LIGHT
* 2 : W/ A/T INDICATOR LIGHT
*
3 : MALFUNCTION INDICATOR LAMP
(
CHECK ENGINE WARNING LIGHT)
*7 : 5S±FE *
6 : 1MZ±FE * 5 : TMM MADE
*
4:TMCMADE
AB
C
COMBINATION METER1
IEIF 2 1B 15 B3B9B13
B 12B 8B14 C 1 C 3 A 9A 10C 2
II1 4
11B DE 18 A
FB E D
8 A
FAFROM POWER SOURCE SYSTEM(
SEE PAGE 64)
B±W
R±Y
R±GW±R Y±G B±W
B±O G± L
G±R
R±Y R±Y W±BG±RG± L
±B W±B
R±W R±W
R±W
G±O
Y
B±Y
R±BB±YY G±O R±Y
R±Y
R±W 10A
STARTER
TO LIGHT FAILURE
SENSOR
FROM º HEAD RHº FUSE
FROM º HEAD(
UP R±RH)
ºFUSE
(
CA NADA) (
USA) CRUISE
(
*3)
BRAKE
BULB
CHECK
RE AR LIGHT
O/D OFF
CHARGE
SRS
HIGH BEAM
PKB BRK
TOO/DMAINSW
TO GENERATOR(
ALTERNATOR)
TO CENTER AIRBAG
SENSOR ASSEMBLY
TO DIMMER SW
[COMB. SW] TO CRUISE CONTROL ECU
TO E NGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)(
A/T)
TO E NGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
BRAKE FLUID
LEVEL SWJUNCTION
CONNECTOR
JUNCTION
CONNE CTOR
DAYTIME RUNNING
LIGHT RELAY
(
MAIN) PARKING
BRAKE SW
PARKING
BRAKE SW(
EX. 1MZ±FE A/T)
(
1MZ±FE A/T)
JUNCTION
CONNECTOR
JUNCTION
CONNECTOR (
USA)
(
CANA DA) C8 ,C9 , C10
J2
J2 B2
P3
P2 D4
J2
J3(
*1) (
*1)
(
USA)
II1 2
I6
G±O
G±O G±O
(
*2) FROM A/T
INDICATOR LIGHT
W±B
(
CA NADA)(
*5) (
*5)
O
(
*4)O
(
*4)
4
3B 203C 2
1D 31F3 7. 5A
IGN7. 5A
SRS
3B 19 3D19 3B 83D18
3D 83C8 3A 10
1M 51C 8
W

256
GROUND POINT*3 :W/POWERWINDOW *
2:TMMMADE * 1 : TMC MADE
* 6 : AIR CONDITIONING(
LEVER CONTROL SW TYPE) *
5 : AIR CONDITIONING(
PUSH CONTROL SW TYPE) * 4 : W/O POWER WINDOW
LIGHT CONTROL SW
[COMB. SW]
KEY INTERLOCK
SOLENOID
WIPER AND WASHER SW
[COMB. SW]
RE AR WINDOW
DEFOGGER SW
CLOCK
CIGARETTE LIGHTER
BRAKE FLUID LEVEL
SW
TURN SIGNAL FLASHER
MOON ROOF
CONTROL RELAY
MOON ROOF MOTOR
MOON ROOF LIMIT SW
RADIO AND PLAYER
STEREO COMPONENT
AMPLIFIERBLOWER RESISTOR
A/C AMPLIFIER HEATER CONTROL SW
(
PUSH CONTROL SW
TYPE)
OR AIR VENT
MODE CONTROL SW
(
LEVER CONTROL SW
TYPE) BLOWER SW
STARTER RELAY
COMBINATION METER
CIRCUIT OPENING
RELAY
DAYTIME RUNNING
LIGHT RELAY(
MAIN)
CRUISE CONTROL ECU
CRUISE CONTROL SW
[COMB. SW]
HEATER RELAY I7
I7
I7
I7
I7
I13I13 I13 I13 I12
IH IG II2F
4 1
IM27F FI5
I5 W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
BR
BR BRW±B W±BW±B
W±B
W±B W±BW±B
W±B
W±B
W±B
W±B
W±B W±B
W±B
W±B W±B
W±B W±B
W±B W±BW±BW±B W±B W±B W±B
W±B
W±BW±B
W±B
VANI TY LIGHT LHAIR VENT MODE CONTROL
SERVO MOTOR
W±B
W±B W±B W±B JUNCTION
CONNE CTOR J1
DIMMER SW
[COMB. SW]
IL17 IK 14
W±B
W±B
CENTER AIRBAG SENSOR
ASSEMBLY(
E2)6
VANITY LIGHT RHW±B W±B
W±B
W±B
MOON ROOF CONTROL SW
AND PERSONAL LI GHT
(
W/ CD PL AYER)(
CANADA)
(
W/O CD PLAYER)IE
W±BIV 2 IV1
(
W/G)(
S /D, C/P) (
*1)W±B W±B
(
*2)
(
*2)
B5:S/D
B21 : C/P
B32 : W/G
B4:S/D
B21 : C/P
B31 : W/G
BK : S/D, C/P
BP : W/G
6 6 W±B
I5
W±B
DA TA LINK
CONNE CTOR 3
F W±B
B4:S/D
B30 : W/G
B20 : C/PI7:*5
I14 : * 6
1 HIGH BEAM INDICATOR
LIGHT [COMB. METER]
CRUISE CONTROL
CLUCH SW W±B
NOISE FILTER
POWER MAIN RELAY
INTEGRATION RELAY
UNLOCK WARNING SW
[IGNITION SW] 1C11
W±B W±B
CENTER AIRBAG SENSOR
ASSEMBLY(
E1)
1G4
1F1
1M1
1I6 1F2
1M 51C 8
3C
3D6
3A13
3A12
3B5
3C 186
3B14DEFOGGER RELAY 1C10