1994 PONTIAC FIREBIRD stop start

Reverse
Press and hold “REV” to rapidly return to
a favorite passage. Release
it to play the
passage. The radio will play during this
operation.
Forward
Press and hold “FWD’ to quickly
advance within a track. Release
it to
resume playing. The radio will play
during this operation.
Random
Press “RDM” to hear a random selection
of tracks.
0
0
0
To Stop the Disc Player
Turn the power off or turn the ignition
key off. The disc stays
in the player
and
will resume playing at the point
where it stopped.
Press
‘‘AMFM’’ to stop playing the
disc and switch to radio. Press
“CDPLAY” to restart
the disc at the
point where it stopped.
Press “EJECT” to eject the disc or
stop the disc and switch to radio.
“EJECT” will work with the ignition
or radio off. Press “EJECT” to load a
disc when the audio system is
off.
Theft-Deterrent System
Your audio system is equipped with the
“THEFTLOCK’ theft-deterrent system.
See “Theft-Deterrent System” at the end
of this
section.
117.. .
ProCarManuals.com

Comfort Controls and Audid Systems
Forward
Press and hold “FWD’ to quickly
advance within a track. Release it to
resume playing. The radio will play
during this operation.
Random
Press “RDM’ to hear a random selection
of tracks.
To Stop the Disc Player
Turn the power off or turn the ignition
key
off. The disc stays in the player
and will resume,playing at the point
where it stopped.
Press
“AM/FM’ to stop playing the
disc and switch to radio. Press
“CDPLAY” to restart the disc at the
point wherk it stopped.
Press “EJECT” to eject the disc or
stop the disc
arid switch to radio.
“EJECT” wili work with the ignition
or radio
off. Press “EJECT” to load a
disc when the audio system is
off.
rheft-Deterrent System
Your auklio system is equipped with the
‘THEFTLOCK” theft-deterrent system.
See “Theft-Deterrent System” at the end
3f this section.
rheft-Deterrent Feature
rHEFTZOCK is a security feature for the
Zassette tape and compact disc player. It
:an be used or ignored. If ignored, the
System functions normally:
If it is used,
your system won’t be usable if it’s ever
stolen. When the system is active, the
indicator light will flash while the ignition
is off.
Setting Your Security Code
The instructions below tell you how to
enter a security code into the system. If
your vehicle loses battery power for any
reason, you must enter the security code
again before the system will turn on.
1. Write down any number from 000 to
1999 and keep it in a safe place.
2. Turn the ignition switch to tHk “ACC”
or “Run” position.
3. T~irn the audio system off.
4. Press and hold pushbuttons “1” and
“4” together until “---” shows on the
display.
You are now ready to enter your security
:ode. Don’t wait more than
15 seconds
between steps.
5. Press “MIN” and “000” will appear
on the display.
6. Press “MIN’ again and hold until the
last two digits of your code appear.
Release the button.
7. Press “HR’ until the first one or two
digits of your code appears.
on tine display.
verification.
8. Press “A”.” “rEP” will appear
9. Repeat steps 5 through 7 for
10. Press “A”.” “SEC” will appear
on the display. This means that your audio system is secured.
. . .I20
ProCarManuals.com

This is a mistake. Your brakes may not
have time to cool between hard stops. Your brakes will wear out much faster if
you do a lot of heavy braking. If you
keep pace with the traffic and allow
realistic following distances, you will
eliminate a lot of unnecessary braking.
That means better braking and longer
brake life.
If your engine ever stops while you’re
driving, brake normally but don’t pump
your brakes. If you do, the pedal may get
harder to push down. If your engine stops,
you will still have some power brake
assist. But you will use it when you brake.
Once the power assist
is used up, it make
take longer to stop and the brake pedal
will be harder to push.
mti-Lock Brakes (ABS)
[our Pontiac has an advanced electronic
lraking system that will help prevent
kidding.
ABS
INOP
This light on the instrument panel will go
on when you start your vehicle.
When you start your vehicle, or when you
begin to drive away, you may hear a
momentary motor or clicking noise. And
you may even notice that
your brake
pedal moves a little while
this is going on.
This is the
ABS system testing itself. If
there’s a problem with the anti-lock brake
system, the anti-lack brake system
warning light will stay on or flash.
129 ...
ProCarManuals.com

Your Driving and the Road
Passing
The driver of a vehicle about to pass
another on a two-lane highway waits for
just the right moment, accelerates, moves
around the vehicle ahead, then goes back
into the right lane again. A simple
maneuver?
Not necessarily! Passing another vehicle
on a two-lane highway is a potentially
dangerous move, since the passing
vehicle occupies the same lane as
oncoming traffic for several seconds.
A
miscalculation, an error in judgment, or a
brief surrender to frustration or anger can
suddenly put the passing driver face to
face with the worst of all traffic accidents
- the head-on collision.
So here are some tips for passing:
“Drive ahead.” Look down the road,
to the sides, and to crossroads for
situations that might affect your
passing patterns. If you have any
doubt whatsoever about making a
successful pass, wait for a better time.
Watch for traffic signs, pavement
markings, and lines. If you can see a
sign up ahead that might indicate a
turn or an intersection, delay your
pass.
A broken center line usually indicates
it’s all right to pass
(providing the road ahead is clear).
Never cross a solid line
on your side
of the lane or a double solid line, even
if the road seems empty of
approaching traffic.
Do not get too close to the vehicle you
want to pass while you’re awaiting an
opportunity. For one thing, following
too closely reduces your area of
vision, especially if you’re following a
larger vehicle. Also, you won’t have
adequate space if the vehicle ahead
suddenly slows or stops. Keep back a
reasonable distance.
When it looks like a chance to pass is
coming up, start to accelerate but stay
in the right lane and don’t get too
close. Time your move
so you will be
increasing speed as the time comes to
move into the other lane. If the way is
clear to pass, you will have a “running
start” that more than makes up for the
distance you would lose by dropping
back. And if something happens to
cause you to cancel your pass, you
need only slow down and drop back
again and wait for another
opportunity. 0
0
0
If other cars are lined up to pass a
slow vehicle, wait your turn. But take
care that someone isn’t trying to pass
you as you pull out to pass the slow
vehicle. Remember to glance over
your shoulder and check the blind spot.
Check your mirrors, glance over your
shoulder, and start your left lane
change signal before moving out of
the right lane to pass. When you are
far enough ahead of the passed vehicle
to see its front in your inside mirror,
activate your right lane change signal
and move back into the right lane. (Remember that your right outside
mirror is convex. The vehicle you just
passed may seem to be farther away
from you than it really is.)
Try not to pass more than one vehicle
at a time on two-lane roads. Reconsider
before passing the next vehicle.
Don’t overtake a slowly moving
vehicle too rapidly. Even though the
brake lights are not flashing, it may be
slowing down or starting to turn.
If you’re being passed, make it easy
for the following driver
to get ahead
of you. Perhaps you can ease
a little to
the right.
. . .I34
ProCarManuals.com

Loss of Control
Let’s review what driving experts say about what happens when the three
control systems (brakes, steering and
acceleration) don’t have enough friction
where the tires meet the road to do what
the driver has asked.
In any emergency, don’t give up. Keep
trying to steer and constantly seek an
escape route or area of less danger.
Skidding
In a skid, a driver can lose control of the
vehicle. Defensive drivers avoid most
skids by taking reasonable care suited
to existing conditions, and by not
“overdriving” those conditions. But
skids are always possible.
The three types of skids correspond to
your Pontiac’s three control systems. In
the braking skid your wheels aren’t
rolling.
In the steering or cornering skid,
too much speed or steering in a curve
causes tires to slip and lose cornering
force. And in the acceleration skid too
much throttle causes the driving wheels
to spin.
A cornering skid is best handled by
Easing your foot
off the accelerator pedal.
[f you have the traction control system,
remember:
It helps avoid only the
acceleration skid. If you do not have
traction control, or if the system is
off,
then an acceleration skid is also best
handled by easing your foot
off the
accelerator pedal.
If your vehicle starts to slide, ease your
bot off the accelerator pedal and quickly
steer the way you want the vehicle to
go.
If you start steering quickly enough, your
vehicle may straighten out. Always be
ready for a second skid
if it occurs.
Of course, traction is reduced when water,
snow, ice, gravel, or other material is on
the road. For safety, you’ll want to slow
down and adjust your driving to these
conditions. It is important
to slow down
on slippery surfaces because stopping
distance will be longer and vehicle
control more limited. While
driving
on a surface with reduced
traction,
try your best to avoid sudden
steering, acceleration, or braking
(including engine braking by shifting to
a lower gear). Any sudden changes could
cause the tires to slide. You may not
realize the surface is ‘slippery until your
vehicle is skidding. Learn to recqgnize
warning clues
- such as enough water,
ice or packed snow
on the road to make a
“mirrored surface”
- and slow down
when you have any doubt.
Remember: Any anti-lock braking system
(ABS) helps avoid only the braking skid.
*:p? ’
‘.I ,
135 ...
ProCarManuals.com

Your Driving and the Road
Backing Up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, just move that hand to the left.
To move the trailer to the right, move
your hand to the right. Always back up
slowly and, if possible, have someone
guide you.
Making 7hms
When you’re turning with a trailer, make
wider turns than normal.
Do this so your
trailer won’t strike soft shoulders, curbs,
road signs, trees, or other objects. Avoid
jerky or sudden maneuvers. Signal well in
advance.
Thrn Signals When Towing a Trailer
When you tow a trailer, your vehicle has
to have a different turn signal flasher and
extra wiring. The green arrows on your
instrument panel will flash whenever you signal a turn or lane change. Properly
hooked up, the trailer lights will also
flash, telling other drivers you’re about to
turn, change lanes or stop. When
towing a trailer, the green arrows
on your instrument panel will flash for
turns even
if the bulbs on the trailer are
burned out. Thus, you may think drivers
behind you are seeing your signal when
they are not. It’s important to check
occasionally to be sure the trailer bulbs
are still working.
Driving on Grades
Reduce speed and shift to a lower gear
before you start down a long or steep
downgrade. If you don’t shift down, you
might have to use your brakes
so much
that they would get hot and no longer
work well.
On a long uphill grade, shift down and
reduce your speed to around
45 mph
(70 km/h) to reduce the possibility of
engine and transmission overheating.
If you are towing a trailer and you
have an automatic transmission with
Overdrive, you may prefer to drive in
“D”
instead of Overdrive (or, as you need to, a
lower gear). Or,
if you have a manual
transmission with fifth (or sixth) gear and
you are towing a trailer, it’s better not to
use fifth (or sixth) gear. Just drive in
fourth gear (fifth gear if you have a six-speed manual transmission) or, as you
need to, a lower gear.
Parking on Hills
You really should not park your vehicle,
with a trailer attached, on a hill. If
-
something goes wrong, your rig could
start to move. People can be injured, and
both your vehicle and the trailer can be
damaged.
But if you ever have to park your rig on a
hill, here’s how to do it:
1. Apply your regular brakes, but don’t
shift into
“P” (Park) yet, or into gear
for a manual transmission.
2. Have someone place chxks under the
3. When the wheel chocks are in place,
release the regular brakes until the
chocks absorb the load. trailer wheels.
4. Reapply the regular brakes. Then
apply your parking brake, and then shift to
“P” (Park), or “R” (Reverse)
for a manual transmission.
5. Release the regular brakes.
. . .I48
ProCarManuals.com

When You Are Ready to Leave after
Parking on a
Hill
1. Apply your regular brakes and hold
the pedal down while you:
0 Start your engine;
0 Shift into a gear; and
0 Release the parking brake.
2. Let up on the brake pedal.
.
3. Drive slowly until the trailer is clear
4. Stop and have someone pick up and
of the chocks.
store the chocks.
Maintenance When Trailer Towing
Your vehicle will need service more often
when you're pulling a trailer. See the
Maintenance Schedule for more on this.
Things that are especially important in
trailer operation are automatic
transmission fluid (don't overfill), engine
oil, axle lubricant, belts, cooling system,
and brake adjustment. Each of these
is
covered in this manual, and the Index will
help you find them quickly. If you're
trailering, it's a good idea to review these
sections before you start your trip.
Check periodically to see that all hitch
nuts and bolts .are tight.
I
I
149.. .
ProCarManuals.com