1994 MITSUBISHI 3000GT bulb

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
Up to 1993 modelsFrom 1994 mod&
__ _..--.
Vertical center lineZ16FO509
JHot
z&ky M-j’ Within~ Within600mm1mm (in.)600 mm
(23.6)
(23.6)
Note l ’ Up to 1993 modelsl 2 From 1994 models
1 Etomj
0000236600002387
LUMINOUS INTENSITY MEASUREMENT
Measure the luminous intensity of headlights with a photo-me-ter in accordance with the instruction manual prepared by
the manufacturer of the photometer and make sure that the
luminous intensity is within the following limit.Limit: 20,000 cd or more
NOTE
(1) When measuring the luminous intensity of headlight, keepthe engine at 2,000 rpm and have the battery charged.
(2) If there are specific regulations for luminous intensity ofheadlights in the region where the vehicle is operated,
make sure that the intensity conforms to the requirements
of such regulations.
FOG LIGHT AIMING
1.Place vehicle on a known level floor 7.6 m (25 feet) from
aiming screen or light colored wall.
2. Use adjusting screw to adjust the top end of high intensity
zone to dimension A.
BULB REPLACEMENT
1. Disconnect the connector.
2. Turn the bulb socket counterclockwise to pull it out.
Caution
Do not touch the surface of the headlight bulb with handsor dirty gloves. If the surface dies become dirty, clean
it with alcohol or thinner, and let it dry thoroughly before
installing.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System54-105FOG LIGHT
REMOVAL AND INSTALLATION
(Up to 1993 models)
,’
..-.-f .- . . .._ 1’yI’-’--.._ . . . ./’‘._,/‘.:‘. . . . . .--ye=.,/‘c’ !:I’:.;; ____-... _.__-.-__~___. . . . . ._./i L.- -3...-.._:.y- .‘...-____ y--. . . . . --‘-T---..-_ -_--._ _ __.-.-.;.? ::.._/ ; .--_.‘7 ,,-y-? ..-,r-; ‘;
‘....lr/I..j ,/L7 rl,-’/I” . . . ..-. ~ -,-.-A:..____ p
A’7----p--*@
,,A..
*~~~~1;’ -“‘.,.
, ‘!U ,.I,/ Ii
8, $&$Jqk2&
4&;. +I+ ’
,,, ’ .’- ‘-I,i
4!a
Removal steps(Up to 1993 models)
1. Front air side spoiler2. Fog light assembly -3. Socket cover4. Bulb
Up to 1993 models
Z16FO268
From1994 models
wZl6FO465
(From 1994 models)
(From 1994 models)
1. Front air side spoiler2. Fog light assembly
Bulb replacement removal steps4.
Lens5. Projector unit6. Bulb7. Bracket
REMOVAL SERVICE POINT
+A, BULB REMOVAL(1) Remove the socket cover (Up to 1993 models).
(2) Remove the bulb mounting spring and remove the
bulb.
CautionDo not touch the surface of the headlight bulb
with bare hands or dirty gloves.
If there are deposits on the surface, loosen and
remove the deposits with a cloth dipped in alcohol
or thinner, and let the surface dry before mounting
the bulb.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-106CHASSIS ELECTRICAL - Lighting SystemFRONT COMBINATION LIGHT AND OPTICAL HORN LENS
REMOVAL AND INSTALLATION(Up to 1993 models)
j&z?&/ optica’ horn Iens
(From 1994 models)
L.JZ16FO216Z16FO47600002392
Removal steps
1. Light cover2. Front combination lightREAR COMBINATION LIGHT AND LICENSE PLATE LIGHT
REMOVAL AND INSTALLATION
I
#d ~
216FO210
Removal steps
1. Rear combination light unit2. Bulb
Rear side trim (Refer to GROUP 52A- Trims.)
3. Socket assembly
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-110CHASSIS ELECTRICAL - Lighting System
1
16FO121
16FO12600002396
I‘VA1 I\ Air outlet assembly _I
RHEOSTAT\
INSPECTIONJL
(1)Remove the instrument panel switch from the knee protec-
tor.(2) Connect the battery and a test bulb (40 W) as shown
in the figure.
(3) The function of the rheostat is normal if the intensity of
illumination changes smoothly, without flashing or flicker-ing, when the rheostat is operated.
HAZARD SWITCH
INSPECTION
(1) Remove the center air outlet assembly from instrument
panel. [Refer to GROUP 55 - Ventilators (Instrument Pan-’
eO.1d
(2) Operate the switch to check for continuity between termi-
nals.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-222CHASSIS ELECTRICAL - Theft-alarm System
TROUBLESHOOTING QUICK-REFERENCE TABLE
For information concerning the locations of electrical components, refer to GENERAL-Theft-alarm System
Circuit.
1.ARMING / DISARMING RELATIONSHIP
Trouble symptomThe system is not armed (The
SECURITY light doesn’t illumi-
nate, and the alarm doesn’t func-
tion.)
(The central door locking system
functions normally.
If the central locking system doesnot function normally, refer to
GROUP 42.)
The arming procedures are fol-
lowed, but the SECURITY light
does not illuminate.(There is an alarm, however,
when an alarm test is conductedafter about 20 seconds have
passed.)
The alarm sounds in error when,
while the system is armed, a door
or the liftgate is unlocked by us-
ing the key.
ICause
Damaged or disconnected
wiring of ECU power sup-
ply circuit
Damaged or disconnected
wiring of door switch input
circuit
Damaged or disconnectedwiring of SECURITY light
activation circuit.Blown SECURITY light
bulb
Malfunction of the ECU.
Damaged or disconnected
wiring of a door key cylin-
der and the
liftgate unlock
switch input circuit.
Malfunction of a door key
cylinder and the liftgate un-
lock switch.
Malfunction of the ECU.
2.ACTIVATION / DEACTIVATION RELATIONSHIP
Trouble symptomCauseThere is no alarm when, as an
Damaged or disconnected
alarm test, a door is opened with-wiring of door switch (all
out using the key.doors) input circuit
(The arming and disarming arenormal, and the alarm is
acti-Malfunction of the door
vated when the liftgate or hood isswitch
opened.)
Malfunction of the ECUThere is no alarm when, as an
Damaged or disconnected
alarm test, the liftgate is opened
without using the key.wiring of liftgate switch in-
put circuit
(The alarm is activated, however,
by opening a door or the hood.)Malfunction of the liftgate
switch.
Malfunction of the ECU.Check methodCheck by using check
chart P.54-224.Check by using check
chart P.54-225.Check by using check
chart P.54-229.
If input checks
(P.54-220) indicate amalfunction, check by
using check chart
P&f-227.
Check method
If input checks
(P.54-220) indicate a
malfunction, check by
using check chart
P.54-225.
If input checks
(P.54-220) indicate a
malfunction, check by
using check chart
P.54-228.
Remedy
Replace the fusible link
No. (6) or the fuse No.
(19).Repair the harness.
Repair the harness or re-
place the door switch.
Replace the fusible linkNo. (6) or the fuse No.(1%
Repair the harness.
Replace the bulb.
Replace the ECU.
Repair the harness or re-
place a door key cylinderand the
liftgate unlock
switch.
Replace the ECU.
Remedy
Repairthe harness or re-
place the door switch.
Replace the ECU.
Repair the harness or re-
place the liftgate switch.
Replace the ECU.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine iCHASSIS ELECTRICAL
- Theft-alarm System54-229
JS!SECURITYE-04@y&fiNAT! ON .$36
152
FUSIBLE LINK CE)m
z0alz!
r%BECATED
mCL
1
TO THE ECUTO THE HORN8. SECURITY LIGHT ACTIVATION CIRCUIT
Description of operation
If all doors are in locked state after key-less locking, the ECUtransistor is turned ON and the security light comes on.
Checking the security light activation circuit (Disconnect the
connector of the ECU and check at the wiring harness side.)Nor-
malMal-
stepCheck objectcondi-func-
Cause
Remedy
tiontion
1D-04connector12v ovterminal voltage 51Fuse (19) dam-Replaceaged or discon-the fusenetted
Harnessdam-Repair the
aged or discon-harnessnetted, or short-circuit
2D-04connector12v ovterminal voltage 52Damaged or dis-
Replaceconnected wiringthe bulbofSECURITYlight bulb
Harness
dam-Repair the
aged or discon-harnessnetted
3ECU terminal volt-12v ovHarnessdam-
age 57Repair the
aged or discon-harnessnetted, or short-circuit9. HORN RELAY POWER-SUPPLY CIRCUIT
Description of operationPower voltage is always supplied to the horn relay.
Checking the horn relay power-supply circuit (Disconnect the
horn relay)
connector terminal
Mal-func-CauseRemedytion
Fuse (3)
dam-Replace the
aged or discon-fusenetted
Damaged or dis-Repair the har-connected har-nessness
TSB Revision